Panasonic EY7440 Support Question
Panasonic EY7440 Support Question
Find answers below for this question about Panasonic EY7440 - DRILL DRIVER 14.4V- MULTI-LANG.Need a Panasonic EY7440 manual? We have 1 online manual for this item!
Question posted by peaderdoyle on February 13th, 2011
Panasonicey7440
my cordless drill is about 3years old it is starting to act up a bit by when i am screwing screws it will slow down cut out i have to give it a little shake to get it going again can u advise me on what is causing this or have u come across this problem before
many thanks peter
Current Answers
Related Panasonic EY7440 Manual Pages
EY7440 User Guide - Page 3
... common sense when operat ing a power tool. The correct power tool will reduce personal injuries.
3) Avoid accidental starting. SAVE THESE INSTRUCTIONS Work Area Safety
1) Keep work area clean and well lit.
Power Tool Use and Care
1) Do not force the power tool. Use the correct power tool for carrying, pulling or unplug ging the...
EY7440 User Guide - Page 4
...tools are caused by a qualified repair person using the tool for the particular type of untrained users.
5) Maintain power tools. Properly maintained cutting tools with water. Use of the power tool for normal operation.
8) Be careful not to control.
7) Use the power tool, accessories and tool bits... like paper clips, coins, keys, nails, screws, or other con dition that may cause...
EY7440 User Guide - Page 5
... reduce risk of damaging the electric plug and cord, pull by power sanding, sawing, grinding, drilling, and other reproductive harm.
take it has received a sharp blow, been dropped, or otherwise ...
extension cord is large enough for ampere rating of the motor.
11)Do not drop the tool. wire size is properly wired and in last page. Other types of batteries may result in...
EY7440 User Guide - Page 6
...bit and turn the lock collar clockwise (looking from the front), then remove the bit. cordless tool...14)Do not attempt to disassemble the battery pack housing.
15)Do not store the tool and battery pack in locations where the temperature may result in the summer), which can explode in place and open the chuck jaws by turning the lock collar and tighten the screw (left-handed screw... tool ...
EY7440 User Guide - Page 7
.... 2. The brake operates and the chuck stops immediately when the trigger is normal. Check the direction of screws and drilling. Clutch Torque Setting
Adjust the torque to one of the trigger for reverse rotation.
NOTE: When the brake...lease the battery pack. Depress the trigger switch slightly to start the tool slowly. 3. After use .
2. Depress the trigger switch slightly to...
EY7440 User Guide - Page 8
...driver (position on the sides of the tool surface, do not operate the tool...tool in an accident or injury.
- -
CAUTION: To prevent excessive temperature increase of the body during operation.
Otherwise, the machine function is held by the belt hook, avoid jumping or running with the screw firmly fastened. This may cause damage to be a little...of the bit lock. ...
EY7440 User Guide - Page 9
...enough brightness. To return the belt hook to either side of the unit.
4.Fasten the screw firmly, turning it as a drill bit, may cause injury or an accident. To secure the lock, follow step 1. The ...hook can be taken out from storing position 2 2 and set it into the other side of the driver during use or its battery capacity. above .
Firmly lock it .
1
3.Release the belt hook
...
EY7440 User Guide - Page 10
... the overheat warning lamp goes out.
• Avoid using the driver in use without charging it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can push against the rear end of the tool, replace the battery pack cover immediately in order to prevent...
EY7440 User Guide - Page 11
... CAUTION: To prevent the risk of fire or damage to prevent overcharging. • Charging will not start flashing quickly in green color.
6. Insert the battery pack firmly into the AC power supply, but ...plugged in, or if after the charger is completed. The orange standby lamp will start if the battery pack is completed, the charging lamp will be produced when the plug is not...
EY7440 User Guide - Page 12
...is completed, the charging lamp will begin when temperature of battery pack drops. Charging will start flashing quickly in green, consult an authorized dealer.
6. Insert the battery pack firmly into...the battery pack.
- 12 -
Battery charger (EY0L80) 1. During charging, the charging lamp will also start if the battery pack is -10°C or less, the charging status lamp (orange) will be...
EY7440 User Guide - Page 13
... RECOMMENDED CAPACITIES
Model Screw driving
Drilling
Machine screw Wood screw Self-drilling screw For Wood For Metal
EY7440 M5
ø 6.8 mm (17/64") ø 6 mm (15/64") ø 35 mm (1-3/8") ø 13 mm (1/2")
IX. SPECIFICATIONS
MAIN UNIT
Model Motor
No load speed
Chuck capacity
Low High
Clutch torque
Overall length
Weight (with battery pack: EY9L40)
EY7440 14.4 V DC 60...
EY7440 User Guide - Page 14
NOTE: This chart may include models that are not available in your area. EY9210 90 min.
- 14 -
Please refer to the latest general catalogue.
24 V
EY9116 EY9117 60 min. EY9136
EY9200 EY9230 45 min.
EY9201 EY9231
55... V
EY9080 EY9086 20 min.
12 V EY9001
15.6 V
EY9180 EY9101 EY9182 EY9103
25 min. [Li-ion battery pack]
Voltage
Charging time
3 Ah
14.4 V EY9L40 Usable: 35 min.
Similar Questions
Pnasonic Battery Terminal Wiring
Panasonic EY7540 impact driver. Where are the four wires connecting to the battery terminal block co...
Panasonic EY7540 impact driver. Where are the four wires connecting to the battery terminal block co...
(Posted by groffee 8 years ago)
Ey7880 Drill
hi there i have a ey7880 that has stopped hammering it just turns do you have any ideas what would c...
hi there i have a ey7880 that has stopped hammering it just turns do you have any ideas what would c...
(Posted by neilcooper2000 10 years ago)
Looking For Ey5917 Case
I would like to replace the carrying case for the 18V Panasonic Drill and Driver.
I would like to replace the carrying case for the 18V Panasonic Drill and Driver.
(Posted by jpkoiman 11 years ago)
Cordless Driver Faulty
The driver was working fine but on a rainy day it sopped working. It does a strange thing. After 24 ...
The driver was working fine but on a rainy day it sopped working. It does a strange thing. After 24 ...
(Posted by atymag 12 years ago)
I Have Panasonic Kx-mb3020 Driver For Win7
(Posted by taherkhani 12 years ago)