Oreck XL 2600HH Support Question
Oreck XL 2600HH Support Question
Find answers below for this question about Oreck XL 2600HH.Need a Oreck XL 2600HH manual? We have 2 online manuals for this item!
Question posted by karenjeansonne on August 21st, 2012
What Is The Reason For The Beater Brush Not Rotating?
The person who posted this question about this Oreck product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Oreck XL 2600HH Manual Pages
Owners Guide - Page 1
... REV A
S I M P LY
A M A Z I N G®
FRANÇAIS
GUIDE D'UTILISATION PAGE 8
E S PA Ñ O L
GUIA DEL USUARIO PAGE 14
USER'S GUIDE
XL2600HH XL2610HH XL2700HH XL2700RH
HIGH SPEED UPRIGHT VACUUM CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLETÀ Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis •...
Owners Guide - Page 2
...some mothproofing substances, or in any period of time.
Close attention is a product of the vacuum. Use only manufacturer's recommended attachments. • Do not use with any object into water,... Fresh Air® Tab, Bulb Replacement, To Adjust or Replace Brush page 7
Maintenance and Customer Service
Your Oreck vacuum cleaner is necessary when used as your sales or purchase slip. ...
Owners Guide - Page 3
...repairs of any direct, indirect, consequential or incidental damages arising out of this product. Brush is broken. This limited warranty does not apply to accident, abuse, commercial use this...intake Clear obstruction. Some states do not allow limitations on housing.
Drive belts, revolving brushes, bulbs, disposable bags, and other rights which means ORECK grants you no warranty, and...
Owners Guide - Page 4
...vacuum cleaner on damp or wet surfaces.
You'll love the way it cleans, gets under warranty. 6. This will pick up properly or
makes an unusual noise, STOP OPERATION and service. 4. The revolving brush... place. Although your ORECK vacuum cleaner. To keep them handy for future reference. WARNING: Do not use . Operating Recommendations This new ORECK XL High-Speed Upright is in...
Owners Guide - Page 5
...important the inside out, with a damp cloth. The roller brush may create undue stress which will affect the cleaning ability of your vacuum cleaner controls the speed of the outer bag be replaced once...connector. Do not operate the unit while in operation. Vacuum the inside of the outer bag or hand wash, turned inside of the revolving brush and is stored in any period of your cleaner....
Owners Guide - Page 6
Slide the door forward by sliding it into fan housing. Rotate the brush roll three (3) complete revolutions to ensure the belt is ... you can not reach the blockage, remove baseplate. If tube is properly seated behind the belt retainer. See illustration D. Vacuum will not operate properly without the tube O-ring. Then reinsert tube and push down screw. See illustration E. ENGLISH
How to...
Owners Guide - Page 7
... replace with new bulb.
• Replace lamp housing by removing 5 screws.
When rotating bearings, make sure both bearing assemblies at each end of the cleaner, many older ...Air® Tab
Your ORECK XL vacuum cleaner has a special FRESH AIR tab pocket.
Bulb Replacement
WARNING: Unplug cord from electrical outlet before servicing. If brush bristles do not correct the problem...
Parts Diagram - Page 3
... Type 1, 2 & 3 Units Only O-030045502
Cord Retainer, Square Type 4, 5 & 6 Units Only
O-030049401
34 Motor Assembly Kit
O-017-0020
35 Motor Seal
O-010-7716
36 Kit, Motor Brush (Large & Small) / Spring
O-7526301
7
Parts Diagram - Page 4
...40 XL2600HH / XL2610HH: Door Belt, Gray
O-7505701436
XL2700HH / XL2700RH: Door Belt, Black
O-7505701327
42 Brush Roll, Plastic Pulley
O-016-1152
43 Seal, Baseplate
O-010-7721
44 Plastic Detent, (uses 2 #49... (use w/#4a or order #83)
O-7558210438
User's Manual
75416-05
Magnet Clean Vacuum Protector
MC4BK
79 Stiffener (uses same length screws, notched)
O-7518902
Stiffener, Through Bolt...
Similar Questions
Brush Does Not Rotate
the brush at base of vacuum is not rotating at all and motor smells like it is bu
the brush at base of vacuum is not rotating at all and motor smells like it is bu
(Posted by Ronsellers1946 5 years ago)
Why Is There No Hose Or Place For Attachments On My Oreck Xl 3760 Vacuum
I have an Oreck XL 3760 Commercial Upright Vacuum. From my research, there are no attachments I can ...
I have an Oreck XL 3760 Commercial Upright Vacuum. From my research, there are no attachments I can ...
(Posted by 106lewis 6 years ago)
Oreck Xl 2600 Brush Issues
I replaced the old worn brush with a new one. i set the "new" tabs up and tried to attach the bottom...
I replaced the old worn brush with a new one. i set the "new" tabs up and tried to attach the bottom...
(Posted by jack21453 9 years ago)
My 2600hh Sparks On The Armature. Will New Brushes Stop This.
The old brush's don't look bad and motor runs.
The old brush's don't look bad and motor runs.
(Posted by jmyers3940 11 years ago)
Oreck Xl Owners Manual
wiring diagram for oreck xl upright vacuum cleaner
wiring diagram for oreck xl upright vacuum cleaner
(Posted by joerock 12 years ago)