Oreck XL 2600HH Support Question
Oreck XL 2600HH Support Question
Find answers below for this question about Oreck XL 2600HH.Need a Oreck XL 2600HH manual? We have 2 online manuals for this item!
Question posted by jmyers3940 on December 13th, 2012
My 2600hh Sparks On The Armature. Will New Brushes Stop This.
The old brush's don't look bad and motor runs.
Current Answers
Related Oreck XL 2600HH Manual Pages
Owners Guide - Page 1
... REV A
S I M P LY
A M A Z I N G®
FRANÇAIS
GUIDE D'UTILISATION PAGE 8
E S PA Ñ O L
GUIA DEL USUARIO PAGE 14
USER'S GUIDE
XL2600HH XL2610HH XL2700HH XL2700RH
HIGH SPEED UPRIGHT VACUUM CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLETÀ Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis •...
Owners Guide - Page 2
...1. Keep cord away from heated surfaces. • Do not run while in operation. • Do not allow to Replace a...Bulb Replacement, To Adjust or Replace Brush page 7
Maintenance and Customer Service
Your Oreck vacuum cleaner is equipped with damaged cord... Tabs 4. SAVE THESE INSTRUCTIONS
Household Use Only
2 The motor bearings are permanently lubricated and should , has been dropped,...
Owners Guide - Page 3
...
POSSIBLE SOURCE AREAS TO CHECK
CLEANER
WILL NOT RUN
Not plugged in wall outlet.
Check bearing seal.
ORECK's limited warranty is not even at each end. No electricity in properly.
Bag tube clogged. Make sure words "old" or "new" match at both ends. Revolving brush is valid only if you retain proof of incidental...
Owners Guide - Page 4
...brush could damage the cord. Be sure the disposable paper filter dust bag is full, REPLACE IT. 3. WARNING: Do not use your new...DO NOT run the vacuum cleaner over
...XL High-Speed Upright is no air can pass through . When inserting a new disposable paper filter dust bag- Although your upright will pick up properly or
makes an unusual noise, STOP...ready to the motor suction fan and ...
Owners Guide - Page 5
... will ensure continued cleaning effectiveness.
Wipe the outside of your cleaner looking new and will hinge downward.
2.
Do not operate the unit while in operation. Pull bag cardboard collar to it will affect the cleaning ability of time. Lubrication The vacuum cleaner motor bearings are not the same. Also clean the connector deflector assembly...
Owners Guide - Page 6
... belt from the brush roll pulley and the motor drive shaft.
Replace the hold down screw located on housing.
6 Under certain conditions it is not blocked, look into the groove ...Vacuum will not operate properly without the tube O-ring. See illustration E. Remove the belt from the storage channel. NEW PHOTO NEW PHOTO
Loop the new belt over the motor drive shaft. Rotate the brush...
Owners Guide - Page 7
...XL vacuum cleaner has a special FRESH AIR tab pocket.
Rotate and match bearing assemblies
NOTE: The bearing assembly setting marked "OLD" has two bars (ll) on them. IMPORTANT: Unless the brush is worn as indicated above actions do not extend beyond baseplate, brush... baseplate at ends of the assembly. The one marked "NEW" has one bar ( l ).
F
Connector Deflector Opening
NOTE: ...
Parts Diagram - Page 3
... Only O-010-1258
XL2700HH / XL2700RH: Cord Retainer, Round Type 1, 2 & 3 Units Only O-030045502
Cord Retainer, Square Type 4, 5 & 6 Units Only
O-030049401
34 Motor Assembly Kit
O-017-0020
35 Motor Seal
O-010-7716
36 Kit, Motor Brush (Large & Small) / Spring
O-7526301
7 Part Numbers Listing: XL2600HH, XL2610HH, XL2700HH & XL2700RH
Hypo Bag, Lights, Helping Hand Handle
# Item
Order # Qty...
Parts Diagram - Page 4
...Gray
O-7505701436
XL2700HH / XL2700RH: Door Belt, Black
O-7505701327
42 Brush Roll, Plastic Pulley
O-016-1152
43 Seal, Baseplate
O-010-7721
...Type 1 Units Order Assembly 1e For Cord Set)
O-7529201327
60 Motor Spring
O-7528301
61 Tube Label
O-7508705
67 Bag Dock Hinge, Type ...O-7558210438
User's Manual
75416-05
Magnet Clean Vacuum Protector
MC4BK
79 Stiffener (uses same length ...
Similar Questions
Brush Does Not Rotate
the brush at base of vacuum is not rotating at all and motor smells like it is bu
the brush at base of vacuum is not rotating at all and motor smells like it is bu
(Posted by Ronsellers1946 5 years ago)
Oreck Xl 2600 Brush Issues
I replaced the old worn brush with a new one. i set the "new" tabs up and tried to attach the bottom...
I replaced the old worn brush with a new one. i set the "new" tabs up and tried to attach the bottom...
(Posted by jack21453 9 years ago)
Where Can I Get New Brushes For The Motor Of The U3700hha?
(Posted by daparkers 11 years ago)
Brush Doesn't Spin
I have a brush that will not spin once in position. The right end cap does not move at all.
I have a brush that will not spin once in position. The right end cap does not move at all.
(Posted by redcedar17 12 years ago)