Oreck XL 2600HH Support Question
Oreck XL 2600HH Support Question
Find answers below for this question about Oreck XL 2600HH.Need a Oreck XL 2600HH manual? We have 2 online manuals for this item!
Question posted by redcedar17 on January 28th, 2012
Brush Doesn't Spin
I have a brush that will not spin once in position. The right end cap does not move at all.
Current Answers
Related Oreck XL 2600HH Manual Pages
Owners Guide - Page 1
... REV A
S I M P LY
A M A Z I N G®
FRANÇAIS
GUIDE D'UTILISATION PAGE 8
E S PA Ñ O L
GUIA DEL USUARIO PAGE 14
USER'S GUIDE
XL2600HH XL2610HH XL2700HH XL2700RH
HIGH SPEED UPRIGHT VACUUM CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLETÀ Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis •...
Owners Guide - Page 2
... Fresh Air® Tab, Bulb Replacement, To Adjust or Replace Brush page 7
Maintenance and Customer Service
Your Oreck vacuum cleaner is necessary when used as your sales or purchase slip. ... or hot ashes. • Do not use appliance in any one stationary position
for any period of the vacuum.
Polarized Plug Notice
This product is a safety feature. Accessories
ITEM 1. Save...
Owners Guide - Page 3
... and that you purchase this product from data plate.
3
This warranty gives you specific legal rights, and you may also have your purchase is found to be sure to the amount paid ... fan housing or connector assembly opening? • Is the belt in place and turning the brush? • Are the brush ends in material or workmanship within three (3) years of the date of the use or inability to...
Owners Guide - Page 4
... revolving brush could damage the cord. To Operate Make sure disposable paper filter dust bag is not full!
You'll love the way it cleans, gets under warranty. 6. Although your vacuum cleaner on...is one of the cleaner's power. WARNING: Do not use . Operating Recommendations This new ORECK XL High-Speed Upright is full, REPLACE IT. 3. The instructions in this manual will pick up ...
Owners Guide - Page 5
...ORECK cleaner. Keep the unit moving while in the upright and locked position. Gently pull bag card cardboard collar upward out of your vacuum cleaner controls the speed of the outer bag be replaced once a ...be used on indication point until it out. It is important the inside of the revolving brush and is stored in extremely dirty areas. For best results, the CELOC SMMS outer bag should...
Owners Guide - Page 6
... , follow the following steps:
WARNING: Unplug cord from electrical outlet before servicing. If your vacuum cleaner does not pick up properly, or makes unusual noise and the outer bag does not ... base, remove lower tube.
Place the opposite end of the belt on side of the brush pulley and roll the belt around the pulley. Rotate the brush roll three (3) complete revolutions to stuff or block...
Owners Guide - Page 7
... at each end of the lamp housing. Rotate and match bearing assemblies
NOTE: The bearing assembly setting marked "OLD" has two bars (ll) on them. IMPORTANT: Unless the brush is worn as indicated above actions do not extend beyond baseplate, brush should be adjusted. ENGLISH
5. Using A Fresh Air® Tab
Your ORECK XL vacuum cleaner...
Parts Diagram - Page 1
...
11
Diagram
83
74 4a
79
8a
5
6 4
67
8
66
62 63
76 3 84 2 15
20 68
53 54
55 38
55
56
82
57
59
7
RIGHT
61
69 10
9
75
12 13 14
68 91 90 89
72
15 21 22
25
26
73 18 19
15 23
24 41
80...
Parts Diagram - Page 3
... Units Only
O-7519805
12 Fan Housing Assembly includes Rivet & Spring
O-097534302
16 End Cap
O-0134623
18 METAXALLOY™ Fan Kit w/Washers
O-097530001
19 Fan Cup Seal
...5 & 6 Units Only
O-030049401
34 Motor Assembly Kit
O-017-0020
35 Motor Seal
O-010-7716
36 Kit, Motor Brush (Large & Small) / Spring
O-7526301
7 Pk.
1b XL2600HH / XL2610HH: Handle Assembly, includes items #38, #53...
Parts Diagram - Page 4
...Brush w/Wheels, Right
O-097525002
51 Wheel Axle
O-010-0159
52 Soft Rear Wheel, Black
75187-02-0327
53 Static Wire Type 1, 2, 3, 4 & 5 Units Only
O-010-9856
54 Switch, 2 Position Assembly Type 1, 2, 3, 4 & 5 Units Only
O-010-8830
Switch, 2 Position...or order #83)
O-7558210438
User's Manual
75416-05
Magnet Clean Vacuum Protector
MC4BK
79 Stiffener (uses same length screws, notched)
O-...
Similar Questions
Oreck Xl 2600 Brush Issues
I replaced the old worn brush with a new one. i set the "new" tabs up and tried to attach the bottom...
I replaced the old worn brush with a new one. i set the "new" tabs up and tried to attach the bottom...
(Posted by jack21453 9 years ago)
Oreck Xl Model Rxl 2600 Hh- How Do U Adjust Levels On Carpet
(Posted by pbresney 10 years ago)
My Brush Is Not Spinning How Do I Remove The Housing Around It
(Posted by mcparis001 11 years ago)
My 2600hh Sparks On The Armature. Will New Brushes Stop This.
The old brush's don't look bad and motor runs.
The old brush's don't look bad and motor runs.
(Posted by jmyers3940 11 years ago)
Oreck Xl Upright Vacum Cleaner - Belt Spinning In Wrong Direction
Belt seems to be spinning in wrong direction...is there a way to reverse the direction of the motor?
Belt seems to be spinning in wrong direction...is there a way to reverse the direction of the motor?
(Posted by enlchicago 12 years ago)