Oreck XL 2600HH Support Question
Oreck XL 2600HH Support Question
Find answers below for this question about Oreck XL 2600HH.Need a Oreck XL 2600HH manual? We have 2 online manuals for this item!
Question posted by Anonymous-75598 on September 21st, 2012
How To Replace Roller Brush On Xl2?
The person who posted this question about this Oreck product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Oreck XL 2600HH Manual Pages
Owners Guide - Page 1
... REV A
S I M P LY
A M A Z I N G®
FRANÇAIS
GUIDE D'UTILISATION PAGE 8
E S PA Ñ O L
GUIA DEL USUARIO PAGE 14
USER'S GUIDE
XL2600HH XL2610HH XL2700HH XL2700RH
HIGH SPEED UPRIGHT VACUUM CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLETÀ Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis •...
Owners Guide - Page 2
..., Troubleshooting Guide page 3 Assembly, Operating Instructions page 4 Operating Instructions Continued, To Replace Filter Dust Bag page 5 How to pick up toxic material such as a handle... to Replace a Worn Belt, Stuffing or Blockage page 6 Using an Oreck Fresh Air® Tab, Bulb Replacement, To Adjust or Replace Brush page 7
Maintenance and Customer Service
Your Oreck vacuum cleaner ...
Owners Guide - Page 3
... electricity in properly. CLEANER
Filter bag is broken.
DOES NOT PICK UP
Replace filter bag. Replace brush if bristles do not allow limitations on the duration of incidental or consequential ...AFTER THIS PERIOD.
WARNING: Unplug cord from data plate.
3
Belt is worn. Brush is broken or Replace belt. Clear obstruction. Bag pores are not covered by other warranty obligation with ...
Owners Guide - Page 4
...4 Operating Recommendations This new ORECK XL High-Speed Upright is not covered under things, and it must be removed from the
connector assembly. The revolving brush could damage the cord. Increase... ensuring the cord
is not full! REPLACE THE BELT EVERY 6 MONTHS. 7. DO NOT operate the cleaner without a paper filter dust bag. Although your vacuum cleaner on damp or wet surfaces. ...
Owners Guide - Page 5
...damaged if used on indication point until it out. The roller brush may create undue stress which will ensure continued cleaning effectiveness. Vacuum the inside of the outer bag or hand wash, ...of the cleaner with the ORECK cleaner. The CELOC layered disposable inner dust bag must be replaced once a month even if it .
A little preventative maintenance will affect the cleaning ability of...
Owners Guide - Page 6
... the opposite end of tube. Replace the hold down screw. Under certain conditions it is properly seated behind the belt retainer. Check for blockage. See illustration B.
2. Remove debris with long-nose pliers, a screwdriver or coat hanger. Vacuum will not operate properly without the tube O-ring.
Rotate the brush roll three (3) complete revolutions to...
Owners Guide - Page 7
... housing. Due to show "old" and replace in the holding channels in the old position.
The one marked "NEW" has one bar ( l ). Unmatched settings will be in the housing.
Using A Fresh Air® Tab
Your ORECK XL vacuum cleaner has a special FRESH AIR tab pocket.
If brush bristles do not correct the problem, contact...
Parts Diagram - Page 3
... Type 1, 2 & 3 Units Only O-030045502
Cord Retainer, Square Type 4, 5 & 6 Units Only
O-030049401
34 Motor Assembly Kit
O-017-0020
35 Motor Seal
O-010-7716
36 Kit, Motor Brush (Large & Small) / Spring
O-7526301
7 Pk.
1b XL2600HH / XL2610HH: Handle Assembly, includes items #38, #53, #54, #55, #56, #57, #59 Type 1, 2, 3, 4 & 5 Units Only XL2700HH / XL2700RH: Handle...
Parts Diagram - Page 4
...40 XL2600HH / XL2610HH: Door Belt, Gray
O-7505701436
XL2700HH / XL2700RH: Door Belt, Black
O-7505701327
42 Brush Roll, Plastic Pulley
O-016-1152
43 Seal, Baseplate
O-010-7721
44 Plastic Detent, (uses 2 #49... (use w/#4a or order #83)
O-7558210438
User's Manual
75416-05
Magnet Clean Vacuum Protector
MC4BK
79 Stiffener (uses same length screws, notched)
O-7518902
Stiffener, Through Bolt...
Similar Questions
What Is The Part Number For The Roller Brush. Is There A Parts Manual Available
(Posted by josephpcallaghan 9 years ago)
Oreck Xl 2600 Brush Issues
I replaced the old worn brush with a new one. i set the "new" tabs up and tried to attach the bottom...
I replaced the old worn brush with a new one. i set the "new" tabs up and tried to attach the bottom...
(Posted by jack21453 9 years ago)
Replacement Cord
What replacement cord does an Oreck XL model 2600HH take? Is it a two wire cord?
What replacement cord does an Oreck XL model 2600HH take? Is it a two wire cord?
(Posted by Smorr64 10 years ago)
Roller Brush Problem
Hi, I received oreck upro14T by shipment. Put it together-double-checked did it right-looked good. W...
Hi, I received oreck upro14T by shipment. Put it together-double-checked did it right-looked good. W...
(Posted by JSIA3 10 years ago)
My 2600hh Sparks On The Armature. Will New Brushes Stop This.
The old brush's don't look bad and motor runs.
The old brush's don't look bad and motor runs.
(Posted by jmyers3940 11 years ago)