LiftMaster RSL12V Support Question
LiftMaster RSL12V Support Question
Find answers below for this question about LiftMaster RSL12V.Need a LiftMaster RSL12V manual? We have 4 online manuals for this item!
Question posted by Kgrimsley on June 28th, 2014
Why Does Gate Not Close Completely?
Chain got debris in it , cleared it and now gate will not close completely
Current Answers
Related LiftMaster RSL12V Manual Pages
RSL12V Installation Manual - Page 2
... Determine Location for Concrete Pad and Operator Concrete Pad and Operator Attachment Attach the Gate Brackets and Chain
WIRING
Earth Ground Rod Power Wiring Connect Batteries Primary/Secondary Operators
ADJUSTMENT
Learn Limits ...Close Auto Open Jumper Heater Party Mode Entrapment Protection Devices
OPERATION AND MAINTENANCE
Reset Switch Remote Control Sleep Mode Maintenance Battery Drive Chain...
RSL12V Installation Manual - Page 3
... order to four single family dwellings, or a garage or parking area associated therewith. CLASS II -
Inherent (built into the operator) entrapment sensing and at least one -to complete a proper installation you must be designed, arranged or configured to protect against entrapments in plain view on both the open and close directions of motorized gate systems.
2
RSL12V Installation Manual - Page 4
... located on the bottom edge. Pedestrians must reduce public exposure to promote pedestrian usage. The pedestrian access opening and closing to mechanical damage. Locate the gate such that enough clearance is supplied between the sensor and the gate operator is greater than 6 inches (152 mm) above the ground to prevent a 2-1/4 inches (6 cm) diameter sphere...
RSL12V Installation Manual - Page 5
... to not fall over more than 8 feet (2.44 m)
function. SPECIFIC APPLICATIONS
2.1 Any non-automated gate that covers in the open position.
4.1.1.2 Except for Automated Vehicular Gate Construction.
These stops shall be installed at either the fully open position or the fully closed position, shall not exceed 2-1/4 inches (57 mm), refer to ASTM F2200 for Exception...
RSL12V Installation Manual - Page 6
...posts or walls.
The safety loops allow the gate to stay open cycle
Edge
sensor for close cycle
Outside
4'
PrOouptesritdyeLSoaofpety
Safety
Danger
Inside
4'
LSoaofepty Inside
Entrapment
Property
Danger
5
Edge sensor for open cycle
Edge sensor for open cycle
Edge sensor for open when vehicles are recommended. Suggested for close cycle
Edge sensor for vehicles 14 feet (4.27...
RSL12V Installation Manual - Page 7
...the unit may come near the operator MUST NOT
be tested. Upon completion of maintenance the area MUST be cleared and secured, at all times. ADJUSTMENT
To reduce the risk of ...the area near a moving gate.
• Locate entrapment protection devices to protect in BOTH the open and close gate. • NEVER use force adjustments to compensate for a binding or sticking gate. • If one ...
RSL12V Installation Manual - Page 8
Upon completion of maintenance the area MUST be cleared and secured, at the fuse box BEFORE proceeding. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.
• Test the gate operator monthly. Have a
qualified service person make repairs to gate hardware. • ALL maintenance MUST be properly grounded and connected in BOTH the open and close
gate cycles...
RSL12V Installation Manual - Page 12
... a direct lightning strike, proper grounding can protect the gate operator in the operator. 2 Close the gate and align the bottom bracket so the chain will require two extra idler pulleys.
1 Move the ... » ATTACH THE GATE BRACKETS AND CHAIN
STANDARD INSTALLATION
DO NOT run the operator until instructed.
1 Open the gate and line up the rear bracket so the chain will be too tight ...
RSL12V Installation Manual - Page 16
... small
children) could be SERIOUSLY INJURED or KILLED by a moving gate. • Too much force on gate will interfere with a rigid object. Gate MUST reverse on the operator.
The programming uses a combination of 6 feet in the fully open position and the fully closed and the
chain is installed and how many operators the installation includes. To...
RSL12V Installation Manual - Page 17
... the desired position, release the button. NOTE: The GATE 1 right and left button to move the gate to jog the gate back and forth as needed .
4 When the gate is now complete. If the SET OPEN LIMIT LED continues to NORMAL OPERATION. Programming is in the desired CLOSED position, press and release the LEARN LIMITS button. When...
RSL12V Installation Manual - Page 18
... LED continues to NORMAL OPERATION. PROGRAM CLOSE
5 Press and hold the GATE 1 left buttons can be used to the desired OPEN position. NOTE: The GATE 1 right and left button to move the gate to jog the gate back and forth as needed .
4 When gate is now complete. PROGRAM OPEN
3 Press and hold the GATE 1 right button to move the learn...
RSL12V Installation Manual - Page 20
... release the LEARN LIMITS button. If the SET OPEN LIMIT LED continues to the desired CLOSED position. NOTE: The GATE 2 right and left operator to the center position
on both operators.
The SET OPEN LIMIT LED will blink. Programming is now complete. PROGRAM CLOSE
6 Press and hold the GATE 1 left button to move the learn limit nut...
RSL12V Installation Manual - Page 21
... are made, test the operator:
1 Use the SINGLE BUTTON to open and close the gate.
1
2 Test the limits by making sure the gate will automatically reverse direction for a short time on the length and weight of one.
3 Run operator through a complete cycle.
If the gate encounters an obstruction the operator will stop and reverse direction for...
RSL12V Installation Manual - Page 23
... sure the battery terminals DO NOT make contact with the operator chassis as this will close the gate after a specified time period. NOTE: To keep the gate open until the operator receives another command from the loops, close edges and close the gate and return the operator to the "ON" position, when the operator reaches a low battery...
RSL12V Installation Manual - Page 24
... will sound (up to 5 minutes) and the operator will have to be cleared before it will stop and reverse to the fully open and close
gate cycles.
• Locate entrapment protection devices to either the CLOSE EDGE or OPEN EDGE/PHOTO terminal on Gate
ProIpnesridtye
1TO REMOVE CHAMBERLAIN PHOTOELECTRIC SENSORS Remove the photoelectric sensor wires from a moving...
RSL12V Installation Manual - Page 25
...opened and closed position, activation of the remote control button will blink in this . The operator does not need to NORMAL OPERATION. PROGRAMMING LIMITS RESET If a mistake is in the closed manually.
When the inherent force of the remote control button will need to shut off the gate rail. A
B
B. Debris is on the gate...LED will open /close the gate.
NORMAL OPERATION
OPERATOR...
RSL12V Installation Manual - Page 28
...LEDs (OPEN EDGE/PHOTO, OPEN PHOTO, CLOSE PHOTO) are ON, clear any... obstructions and verify the LED turns off . Use the on J17 to RESET/DISCONNECT. 2. If any are OFF. Toggle the RESET switch and verify that the gate moves freely. If this product. Check battery connections and battery voltage to the
header.
• The gate is ON, clear...
RSL12V Installation Manual - Page 29
.... SOUNDS WHENEVER A COMMAND IS ISSUED. ALARM IS BEEPING 3 TIMES ON A
COMMAND GATE RUNS TOO SLOW.
Replace battery if necessary. • An open loop or vehicle probe to make sure they are clear of close photoelectric sensors or safety loop. Check the open input is toggled while at slow speed all obstructions. Verify entry system connections...
RSL12V User Manual - Page 2
... NORMAL OPERATION position. MODEL RSL12V SLIDE GATE OPERATOR Model RSL12V has a reset switch. MODEL RSW12V SWING GATE OPERATOR Model RSW12V has a reset button. When referring to "toggling" the reset switch it means pressing the reset switch to the RESET/DISCONNECT position, then back to NORMAL OPERATION. To open and close the gate and return the operator to...
RSL12V Wiring Diagram Manual - Page 1
...Red 40
Dual Gate Wiring Kit
Brown Gre
•
• J16
•
•
0 •
Mock
NC-6 -
CTRL PWR
s
Open (Exit Loop... conditions, such as inside the house or garage.
• When the transformer ispluggedinto the...To
A -6
-_
CTRL PWR
on a dedicatedMyatt, cokulatedusingNEC guidelines.
SLIDE RSL12V & RSL12VH
®WARNING
To protect against fire: • Replace ONLY...
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 8 months ago)
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Alarm Going Off Almost Non-stop. Help!
Hello. I have an RSL12V unit for residential use. I went to open it the other day and the alarm trig...
Hello. I have an RSL12V unit for residential use. I went to open it the other day and the alarm trig...
(Posted by amcollectibles4 2 years ago)
Gate Wont Reset
turned gate to reset to allow several vehicles access. Now when turned back to NORMAL OPS it won't o...
turned gate to reset to allow several vehicles access. Now when turned back to NORMAL OPS it won't o...
(Posted by chizg 9 years ago)
Vehicular Gate Operator Rsl12v Not Opening
Will chirp but the gate does not move at all
Will chirp but the gate does not move at all
(Posted by Krcremodeling 10 years ago)