LiftMaster MT Support Question
LiftMaster MT Support Question
Find answers below for this question about LiftMaster MT.Need a LiftMaster MT manual? We have 2 online manuals for this item!
Question posted by Raggz6 on September 29th, 2015
Key Pad Opener
looking for a key pad opener for my lift master MR 5011 without sensor
Current Answers
Answer #1: Posted by TommyKervz on October 2nd, 2015 3:49 PM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,803
Member since:
January 10th, 2013 Points: 17,776,803
Click here or call (800) 528-5880 for LiftMaster enquiries.
Related LiftMaster MT Manual Pages
MT5011E Installation Manual - Page 1
INSTALLATION MANUAL
MODEL MT5011E/BMT5011E
MEDIUM DUTY DOOR OPERATOR
RaNdoBiwuoiRlwteiitcnheiver
INTENDED FOR PROFESSIONAL INSTALLATION ONLY
Visit www.LiftMaster.com to locate a professional installing dealer in your area.
2 YEAR WARRANTY
Serial # (located on electrical box)
Installation Date
Radio Receiver Built on Board
315MHz
NOT FOR RESIDENTIAL USE
A SAFETY DEVICE IS HIGHLY RECOMMENDED.
MT5011E Installation Manual - Page 2
... must read and fully understand this Signal Word on the following pages, they will
AAVVEERRTTIISSSSEEMMEENNTT alert you to the possibility of damage to your commercial door and
gate operator unless you are an Authorized Service Technician. TABLE OF CONTENTS
SAFETY INFORMATION 2 APPLICATION 3 OPERATOR DIMENSIONS 4 OPERATOR SPECIFICATIONS 4 CARTON INVENTORY 5 PREPARATION 5 ASSEMBLY...
MT5011E Installation Manual - Page 5
...Before beginning your installation check that all components were provided.
15 1
14
^
^OPEN
CLOSE
O
STOP
8
4
10 9
7
2 12
3
13 11
6 5
ITEM DESCRIPTION
QTY
1
Operator
1
2
Track (left & right)
Door height plus 2'
2
3
Track Spacers
2
4
Front Idler
1
5
Trolley
1
6
Take-up Bolt
1
7
Chain
1
8
Master Links
2
9
Header Bracket
1
10
Header Pivot Shaft
1
11
Curved...
MT5011E Installation Manual - Page 11
...Door
Door Bracket
Use appropriate hardware to secure door bracket to door manufacturer's instructions for recommended installation guidelines.
11 Concrete anchors MUST be used if installing ANY brackets into masonry. T Y P I C A L I N S T A L L A T I O N WARNING
6 Hang the operator
Secure the operator using appropriate fasteners and locking hardware that will support the weight of the garage...
MT5011E Installation Manual - Page 13
...DEATH, install reversing sensors when: • The radio is used. • The 3-button control station is out of sight of the door. • ...OPEN
^OPEN
CLOSE
O
STOP
Knockout
Logic Board
Control
Remove factory jumper
if external interlock is used
R27
TTC
LEARN STOP CLOSE OPEN LEDD14
1
2
3
4
5
6
7
LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN
Stop Close Open
3-Button Control Station
^^OPEN...
MT5011E Installation Manual - Page 14
... hole in the side of the electrical box.
Depress retaining plate
Adjust OPEN limit
Retaining Plate OPEN Limit Nut OPEN Limit Switch CLOSE Limit Nut
AVERTISSEMENCLTOSE Limit Switch
ATTENTION
Increase Door Travel
Adjust CLOSE limit
Increase Door Travel Decrease Door Travel
AVERTISSEMENT
AVERTISSEMENT Decrease Door Travel
SAFETY Limit Switch
NOTE: When retaining plate is released, verify...
MT5011E Installation Manual - Page 15
... Optional Safety Device Configurations for wiring information.
15
If an obstruction breaks the light beam while the door is closing , the door will stop and typically reverse to the full open position.
Remove Tape Holding Cotter Pin to Spring
Insert Cotterpin
Clutch Nut
A
To Loosen
Clutch Nut To Tighten
B
Bend ends of cotterpin...
MT5011E Installation Manual - Page 16
... electric or pneumatic sensing edge 2-wire electric or pneumatic sensing edge
(White/Black) (White)
16
5
6
7
ANT
X ANT
TTC
^^^^
1
LEARN STOP CLOSE OPEN LEDD14
2
3
45
LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN
67
OPTIONAL SAFETY DEVICE CONFIGURATIONS
CPS Photo-Eyes
(White) (White/Black)
NOTE: When installing model CPS-LN4, connect the brown wire...
MT5011E Installation Manual - Page 17
...
LEDD14
1
2
3
4
5
6
7
LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN
8
9
10
ITEM 1 2 3 4
5 6 7
8
9 10
DESCRIPTION Open Button Close Button Stop Button Learn Button
Timer to Close Button Purple Wire Antenna Auxiliary Antenna Connection
LED
Field Wiring Terminal Factory Wiring Connector
FUNCTION Open Door Close Door Stop Door Programs the remote controls and performs additional programming...
MT5011E Installation Manual - Page 18
... the close command.
Some wiring types will stop with constant pressure to close.
• Open override that reverses when closing after a 5 second delay and will automatically convert to B2 wiring...possible SEVERE INJURY or DEATH, install reversing sensors when: • The radio is used. • The 3-button control station is out of sight of the door. • Or ANY other control (...
MT5011E Installation Manual - Page 19
...) • Timer to Close (TTC) feature not available.
D B2 WIRING TYPE WITH MONITORED SAFETY DEVICE
• Momentary contact to open , close and stop . • Open override that reverses when closing by any opening
device. • Wiring for safety device to reverse. Electrical Box Logic Board
NO PROGRAMMING REQUIRED
014A1030
J4 C32
TP1 C20...
MT5011E Installation Manual - Page 20
...LiftMaster monitored safety device. The LED will become active after a preset time, adjustable from the open command. TO VERIFY TIMER TO CLOSE (TTC) SETTING
1. MODE
B2 B2 with FCC and ... seconds. 3. TIMER TO CLOSE (TTC)
Timer to Close feature enables the operator to Comply with door in fully closed position. 2. Press and release the TTC button. 3.
The TTC will light). ...
MT5011E Installation Manual - Page 21
... REMOTE CONTROL * Requires B2 wiring type and compatible LiftMaster remote
control. Door should open the door only. 1. Allow the door to trolley. Press remote control button. 4. Allow door to obstruction and reverse if sensing edge is CLOSED.
Emergency disconnect will open .) 2.
Door Arm
Lift free end of persons and obstructions. Release handle. Emergency disconnect will close...
MT5011E Installation Manual - Page 22
...TTC temporarily disabled
➤ Close and Open the door. REMOTE CANNOT BE LEARNED
B) Remote ...pads are actuating freely and releasing properly.
➤ Verify jumper is located at terminals L1 & L2. B) Brake not releasing (if present)
C) Door operation problem
OPERATOR MOVES IN OPEN and CLOSE button wiring THE WRONG DIRECTION connection reversed
DOOR DRIFTS AFTER OPERATOR STOPS
A) Door...
MT5011E Installation Manual - Page 23
...
Grey
Safety Limit Switch
Open Limit Switch
Grey
Close Limit Switch
23
AANTUX ANT
J2
TTC
LEARN STOP CLOSE OPEN LED
1
2
3
4
5
6
7
LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN
OPEN CLOSE STOP
Remove Jumper... cycled to install external door interlock.
Replace Logic Board.
TROUBLESHOOTING
The status of the LED on the capacitor.
Check clutch adjustment. Door height or speed may ...
MT5011E Installation Manual - Page 26
... bracket, springs and cotter pin. K75-12870 Door arm kit
Complete with Master Link Brake Plate Pad Assembly Track for doors 8' to 10' Track for doors 10' to 12' Track for 14' doors #48 Chain for doors 8' to 10' #48 Chain for doors 10' to 12' #48 Chain for 14' doors
26 Clutch Disc Clutch Plate Pulley 4L, 7" Motor...
MT5011E Installation Manual - Page 27
...control wiring.
02-103
^
^ OPEONPEN
CLOSE CLOSE
O
STOP
02-109
OPEN
CLOSE
3-Button Control Station: Steel enclosure.
Key Control Station: Indoor flush mount, NEMA 1.
21-2LM
2-Strand 22 AWG ... controls.)
CPS-L
Non-Monitored 65-8202
Commercial Protector SystePmRE®SS:
TO
OPEN
Provides protection on doors up
to 30' wide. CONTROL STATIONS
02-102
2-Button Control Station: Steel...
MT5011E Installation Manual - Page 28
... Interlock is added to ensure proper installation and operation
with the Commercial Door Operator.
3 BUTTON STATION OR 3 POSITION KEYSWITCH WITH SPRING RETURN TO CENTER AND STOP BUTTON
STANDARD 7635
2 OR MORE 7635
KEY LOCKOUT 7635
Open Close Stop
Open Close Stop
Open Close Stop
Open
Close Stop
Keyswitch
2 BUTTON STATION OR 3 POSITION KEYSWITCH WITH SPRING RETURN...
MT5011E QuickStart Guide Manual - Page 1
... the total door system is safe for its intended use 3 of timer setting.
Programming Remote Controls
7
6
5
3
White/Black White
LiftMaster® CPS Safety Sensors
SINGLE BUTTON ...active after the next open cycle. Example: 30 second TTC = 6 presses of the remote
control until LED flashes rapidly, then release. 4. QuickStart for the model MT/BMT door operator Medium Duty Logic
...
MT5011E QuickStart Guide Manual - Page 2
... installing dealer in the electrical box enclosure. BHreaacdke6ert
2
1st
2nd
5
QuickStart for the model MT/BMT door operator
IMPORTANT: This QuickStart is intended to be comprehensive. Please consult the manual and/or a qualified technician for Professional Installation Only. OPEN CLOSE STOP
Arm Assembly
Pivot Bolt
1
Approximately 4 Feet Half the Height of the track...
Similar Questions
Parts For Mt5011
what reciver an transmitter do I need for a mt5010 lift master opene
what reciver an transmitter do I need for a mt5010 lift master opene
(Posted by jbbouncers 2 years ago)
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
My Lift Master Mt-1211, 1/2 Hp
Will open from closed position but will not close when opened.Tried both remote and wall control. th...
Will open from closed position but will not close when opened.Tried both remote and wall control. th...
(Posted by patrickkaren86 6 years ago)
How Big Of A Garage Door Will A Model Mt 1211 Lift Weight And Width ?
I have a 13' wide 8' high door. Its a older heavy door. I have a new model MT 1211 I had for a 9' wi...
I have a 13' wide 8' high door. Its a older heavy door. I have a new model MT 1211 I had for a 9' wi...
(Posted by crusin31again 10 years ago)
Mh Liftmaster Garage Door Will Not Open Intermittently.
On the occasion when the garage door will not open, there is power to the opener. Both leds on the p...
On the occasion when the garage door will not open, there is power to the opener. Both leds on the p...
(Posted by kellhowarda 11 years ago)