LiftMaster LA400 Support Question
LiftMaster LA400 Support Question
Find answers below for this question about LiftMaster LA400.Need a LiftMaster LA400 manual? We have 3 online manuals for this item!
Question posted by neoparallax on July 24th, 2018
Mg1300 Wiring To La400
Hi, how I can wire mg1300 to LA400? My understanding is: PS minus to B & G on the lock, PS + to NC terminal on the board, W & R from the lock to terminal C on the board.Thanks,V.
Current Answers
Related LiftMaster LA400 Manual Pages
LA400 Manual - Page 1
The operator can be used in Class I, Class II and Class III applications.
2 YEAR WARRANTY
Radio Receiver Built on Board
315 MHz LA400 & LA400-S
MEDIUM DUTY SWING GATE OPERATOR
OWNER'S MANUAL
MeBtOoLaaxplrtC(giXooennLMatrl)ol
Serial # Primary Arm Serial # Secondary Arm Serial # Control Box Installation Date
The LA400 is intended for use with vehicular swing gates.
LA400 Manual - Page 2
...read and fully understand this Signal ...Open Bracket Determine Position of the "Optional" Push-to-Open Bracket Assemble Gate Post Bracket (Pull-to-Open...WIRING
Connect the Gate Operator (Gate 1) to the Control Box Set the Bipart Delay (Model LA400-S Only) Connect the Gate Operator (Gate 2) to the Control Box (Model LA400-S Only) Junction Box (Model LA400-S Only) Connect Transformer to Control Board...
LA400 Manual - Page 3
...
CLASS
CLASS I - CLASS III - In order to four single family dwellings, or a garage or parking area associated therewith.
COMMERCIAL/GENERAL ACCESS
III
VEHICULAR GATE OPERATOR
A vehicular gate operator ...GATE OPERATOR
II
A vehicular gate operator (or system) intended for use on both the open and close directions of the three UL325 classes. Below are the four types of motorized ...
LA400 Manual - Page 4
...or maintained systems can create high levels of force in its wiring arranged so the communication between the gate and adjacent structures when opening shall be located at least 6 feet (1.83 m) away...of many component parts. A wireless contact sensor shall function under , around or through the openings anywhere in the gate, and in that transmits radio frequency (RF) signals to operate the...
LA400 Manual - Page 5
... gate shall not be guarded or covered.
These stops shall be installed at either the fully open position, subject to the provisions in the 4.1.1.1 and 4.1.1.2.
3.1
The following provisions shall apply... refer to ASTM F2200 for barbed wire shall not be less than 6 feet (1.83 m)
3.1.5 All gates shall be required to limit travel to the designed fully open position shall not exceed 4 inches...
LA400 Manual - Page 6
... A swinging gate shall NOT open and close gate. • NEVER use force adjustments to follow ALL specifications and warnings described below. Check with proper weatherproof fixtures. WIRING
To reduce the risk of ... , the safety reversal system MUST be performed until disconnecting the electrical power and locking-out the power via the operator power switch. Upon completion of FIRE or INJURY...
LA400 Manual - Page 8
...Terminal...Sign (2) • Battery (2) • Plug-in Transformer (1)
LA400-S (SECOND GATE OPERATOR ARM)
• Motor Cable - Six ...Open Bracket (1) • Hex Bolt 5/16"-18 X 1-1/2" (5) • Square Neck Carriage Bolt 3/8"-16 X 6" (2) • Hex Nut 3/8"-16 (2) • Hex Nut 5/16"-18 (5) • Flat Washer 5/16" (5) • Flat Washer 3/8" (5) • Lock Washer 5/16" (5) • Lock...
LA400 Manual - Page 10
... Sensors
RIGHT-HAND GATE
NOTE: One or more non-contact sensors shall be exercised to protect the low voltage wire from lawn mowers and string trimmers.
8 feet (2.4 m)
Earth Ground Installation (Optional)
9 Warning Sign
Gate ...
Hinge Post Bracket
Gate Bracket
PVC Conduit (not provided) to reduce the risk of entrapment or obstruction exists at either the opening or closing direction.
LA400 Manual - Page 11
...m)
Earth Ground Installation (Optional)
NOTE: One or more non-contact sensors shall be exercised to protect the low voltage wire from lawn mowers and string trimmers. Care shall be located where the risk of nuisance tripping, such as when a ... Photoelectric Sensors
PVC Conduit (not provided) to reduce the risk of entrapment or obstruction exists at either the opening or closing direction.
LA400 Manual - Page 21
... ground screws inside the control box.
Lift
the
door
from
the
hinges
and ALARM LOCK GATE 1
setSOL
GND MAGR
LEARN XMITTER
ON
OFF
LOCK /
BIPA RT DELAY
BR
GR
WH
YL
BL
GATE 1
RD
SET OPEN LIMIT
SET CLOSE LIMIT
LEARN LIMITS
aside CLOSE EDGE
OPEN EDGE/ PHOTO
OPEN PHOTO
CLOSE PHOTO
ACCESSORY POWER
12 V
BR...
LA400 Manual - Page 24
...a solenoid lock is being used on a gate, the gate with the lock attached to it is OFF. Connect to open first and close second. WIRING » SET THE BIPART DELAY (MODEL LA400-S ONLY)
SET THE BIPART DELAY (MODEL LA400-S ONLY...Primary Gate - The range is 0 to Gate 1 connections on Control Board. This would happen if there was an ornamental overhang on one gate will need to Gate 1 Connector...
LA400 Manual - Page 25
...Extension Cable
PVC conduit at least 18" (45.7 cm) below ground level (grade)
Terminal blocks can be used for the extension cable. Insert extension cable through watertight connector nut ...bury the extension cable.
WIRING » CONNECT THE GATE OPERATOR (GATE 2) TO THE CONTROL BOX (MODEL LA400-S ONLY)
CONNECT THE GATE OPERATOR (GATE 2) TO THE CONTROL BOX (MODEL LA400-S ONLY) Before digging...
LA400 Manual - Page 26
WIRING » JUNCTION BOX (MODEL LA400-S ONLY)
JUNCTION BOX
The following items are required to be used for the
watertight connectors.
2
3 Mount the junction box within 5 feet (1.5 m) of the junction box (not provided).
6 Secure with 3/4" NPT threaded port holes
• Screws • PVC Conduit
1
1 Open the junction box by removing screws (4) and set aside...
LA400 Manual - Page 27
...187; JUNCTION BOX (MODEL LA400-S ONLY) 7 Insert wires from extension cable and operator cable into terminal block
connector.
7
OpOeprearattoorrCCabaleble
SpeTecrmiainlal Block ConnCoencnetcotorr
BBrroowwn n GGrreeeenn WWhhiittee YYeellllooww BBluluee RReedd
BBrroowwn n GGrreeeenn WWhhiittee YYeellllooww BBlluuee RReedd
ExtEexntesnsiioonnCCabaleble
8 Put wires inside of junction box. 9 Secure...
LA400 Manual - Page 28
...WIRING » CONNECT TRANSFORMER TO CONTROL BOARD
CONNECT TRANSFORMER TO CONTROL BOARD
NOTE: All power wiring should be located in the standard control box for suitability of wire installation. NOTE: The transformer must be plugged into the receptacle inside the house or garage...Off Off
Off
Off
Off
Off
Air (1) Conditioner
Main Room
LA400
Bathroon. Manu. 2 Rm
27 This will create more ...
LA400 Manual - Page 38
...), exit loop detectors, keypads and 7-day timers may be wired to this input. Upon removing the obstruction, the gate will have no effect. TERMINAL P9 -
Order part number LA400-BOX to the open limit.
37
blue
brown
CLOSE EDGE
OPEN EDGE PHOTO
brown blue brown blue
OPEN PHOTO
brown
blue
brown
blue
CLOSE PHOTO
brown blue...
LA400 Manual - Page 39
...for gates. Solenoid Lock (optional)
MAGLOCK NO C NC
ACCESSORY POWER 24V
Maglock (optional)
MAGLOCK NO C NC
(not provided)...Ranges
VOLTAGE +24 Vdc
Emitter with the LA400 to control box depending on three sides. (Requires mounting channel. Miller MGR20 2-wire electric edge in 5 feet (1.5 m) ...
DUAL MODE NC EDGE
2 F3
NO
NC PHOTO
S1
K2
DIAGNOSTIC
GATE 1
K1
Q9
SET OPEN
LIMIT
SET ...
LA400 Manual - Page 46
... WILL EXIST OR APPLY AFTER SUCH PERIOD. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. This limited warranty gives you...
LA400 Manual - Page 47
MG1300
Vehicle Exit Sensor: One piece outdoor buried vehicle motion detector with sensing probe is housed in case of cable. Can be welded onto gate or post. 12 Vdc operation, solenoid-activated release. Requires separate power supply (Model ARMP5). Recommended for free exit only.
OPEN
LM202
02101
OPEN OPEN
OPEN
370LM
1-Button Station:
Steel enclosure wired station...
LA400 Pull to Open Addendum Manual - Page 1
... Hinge Point
Gate Post
Gate Hinge Point
7"
Opener Hinge Point 7"
Gate Post
Gate Hinge Point
7"
Opener Hinge Point
7"
7" Opener Hinge Point
7"
Gate Post Gate Hinge Point
7" Opener Hinge Point
7"
7"
Opener Hinge Point 7"
Gate Post
Gate Hinge Point
7"
Opener Hinge Point
7" Typical 6" Post Hole
Can also be approximately 7" x 7". LA400 BRACKET CONFIGURATIONS
Assemble bracket. NOTE: This new...
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 8 months ago)
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Car To La400
how do you connect the La400 to a door opener in the car
how do you connect the La400 to a door opener in the car
(Posted by vanvrancken 6 years ago)
How To Connect A Gatemate Free Exit 5 Wire System To A La400s
What connections do you use on the control board?
What connections do you use on the control board?
(Posted by albeech56 10 years ago)