Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by nishizaki on October 11th, 2014
I Get An R1 Error When I Try To Run My Clean Washer Cycle. What Does This Mean?
I get an r1 error when I try to run my clean washer cycle. What does this mean?
Current Answers
Answer #1: Posted by sabrie on October 11th, 2014 7:07 PM
sabrie
Member since:
May 23rd, 2013 Points: 3,306,778
Member since:
May 23rd, 2013 Points: 3,306,778
list of error codes on the link below to help you understand your error
http://www.applianceblog.com/mainforums/threads/10283-He2-Error-Codes
www.techboss.co.za
Related Kenmore HE2t Manual Pages
User Guide - Page 8
... Number Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White...
User Guide - Page 19
...load up to give the optimum cleaning, rinsing, and spinning conditions.
SPIN SPEEDS
This washer automatically selects the spin speed based on the cycle selected. This washer offers up to conserve resources and lower your new washer...means fewer loads. The time of the washer will illuminate for small and large loads size.
SUSPENSION SYSTEM
To reduce washer "walk" and "off -balance loads ...
User Guide - Page 22
... wash cycle. To load washer
Open the washer door by pulling on the washer by selecting POWER. Load evenly.
• Wash small items such as it stops.
Open the dispenser drawer and add laundry additives to select ON or OFF.
7. The preset settings provide the recommended fabric care for a medium-sized load. The signal is clean before a new cycle can...
User Guide - Page 26
...-speed tumbling, longer wash time, and high-speed spin to clean heavily soiled, colorfast fabrics.
Preset Cycle Settings
Each cycle has a preset Cycle Time, WASH/ RINSE TEMP, and SPIN SPEED. See chart. Cycle
Sanitary Whitest Whites Heavy Duty Normal/Casual Quick Wash (2-3 items) Delicate/ Hand Wash Clean Washer Rinse/Spin Drain/Spin Soak
Estimated
Time* (hr:min...
User Guide - Page 27
.... See "Cleaning The Washer."
IMPORTANT: Do not place garments or other items in the display window.
3-9 Use this to help improve the removal of the laundry, and a soaking time without spin assures gentle treatment, even for equal distribution of set -in stains. This cycle combines fast-speed tumbling and highspeed spin.
NOTE: Loads of set...
User Guide - Page 29
..., dresses, skirts, shirts and blouses, fabrics made of silk, and special care items marked "Hand Washable"
Clean Washer No clothes
Rinse & Spin
All loads
Drain & Spin
All loads
Soak
All loads
Delay Wash
AVAILABLE OPTIONS
Extra Rinse
Pre
End of these washer cycles. Listed to the right are the options available to the chart below for suggested...
User Guide - Page 30
... down these instructions completely before beginning the cleaning process.
• If necessary, the cleaning cycle may be run to cancel the failure code.
b) If any detergent to start the cycle again.
3-12
Then repeat steps 1, 2 and 6 to this cycle.
IMPORTANT:
NOTE: Do not add any items are detected in the washer, all areas under the seal/bellow...
User Guide - Page 31
... parts under running water. WATER INLET HOSES
Replace inlet hoses after each cycle to the washer.
If storing or moving your washer for better ventilation and drying of washer interior. To winterize washer:
1. Unplug washer or disconnect power.
4. Shut off the water supply to allow for better ventilation and drying of washer interior.
• Repeat the cleaning procedure monthly...
User Guide - Page 32
... panel clips.
4. Use 1/2 the manufacturer's recommended amount for a medium sized load.
3-14
sual cycle. To avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician. Run the washer through the Normal/ Casual cycle to clean the washer and remove the antifreeze, if used. Shut off both water faucets...
User Guide - Page 34
... or laundry tub. See "Secure the Drain Hose."
• Is the sink or drain clogged? Do not use ?
DISPENSER OPERATION
• Did you put powdered or liquid color-safe bleach into the dispensers. Clean the fabric softener dispenser. This washer has a tight seal to avoid odors, see "Cleaning The Washer."
• Are you run the Clean Washer Cycle lately...
User Guide - Page 35
WASHER OPERATION
WASHER WON'T RUN, FILL, ...8226; Is the power cord plugged into a grounded 3 prong outlet. This will not affect cleaning performance.
3-17 Turn on ? See "Secure the Drain Hose." NOT ENOUGH WATER / NOT...• Is the load balanced? The washer pauses for leaks.
• Is the washer in a normal pause in this washer. Cycle will see little or no water splashing in...
User Guide - Page 80
... of the main relays is not a siphon problem.
2. MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure; Unplug washer or disconnect power. 2. Check the MCU by running a Diagnostic Test or any cycle.
Make sure that the pressure switch hose is in the inlet valves. - Verify there is not working properly. The machine...
User Guide - Page 81
... Reference Status LEDs chart, page 6-4
Reference Status LEDs chart, page 6-4
DOOR SWITCH ERROR
If the door has not been opened during high-speed spin, the door unlocks after...failure.
6.
Unplug washer or disconnect power. 3. Unplug washer or disconnect power. 2. Verify CCU operation by running a Diagnostic Test or any cycle. LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE
If at the ...
User Guide - Page 82
... wire harness connections to show the failure codes. Check/clean drain pump filter of the excess detergent.
1.
Run a NORMAL cycle without tumbling, the water will be drained and it is...during the drain or spin phases, the washer will fill 4 liters of water and during 5 minutes the unit will try to spin or drain again. Run the unit through a RINSE/SPIN cycle. - Check drain pump. 7. Check...
User Guide - Page 83
... This executes the automatic test but does not show the error history.
• Close the door.
• Push POWER.
• Select the CLEAN WASHER cycle.
• Press EXTRA RINSE four times within 5 seconds...Display the error states that have been recorded by the appliance.
• Run through an automated test.
• Run loads to start the test.
1. All of error codes.
DIAGNOSTIC...
User Guide - Page 84
... turning on the status lights.
• The next most recent error code is to be Checked
Door lock system
Clean Washer Delicate
Clean Washer
Distribution system is set to the maximum speed.
Drain pump
Motor ... lights should turn off and the most recent error code is displayed.
• All of the cycle lights will flash and the error code will be displayed on all lights should ...
User Guide - Page 87
...'s instructions for stained areas. d) Wipe down these instructions completely before beginning the cleaning process.
• If necessary, the cleaning cycle may be run to thoroughly rinse the remaining bleach from the unit. Reconnect wire harness. Unplug washer or disconnect power.
2. Open the washer door and remove any clothing or items from the MCU.
3. Inspect the gray...
User Guide - Page 88
... CLEAN WASHER cycle.
6.
a) If no items are detected in the washer, all cycle lights will flash and the WASH and CONTROLS LOCKED lights will determine if clothing or other causes.
6-10 Press PAUSE/CANCEL to start the cycle again.
8. NOTE: Do not add any clothing or items from the washer.
2. The door will rotate while the washer runs...
User Guide - Page 89
...running a Diagnostic Test or
any cycle.
1. Check that the drain hose and drain pump filter are clear of line cord and line filter.
5. Check the wire harness connections.
6.
Check for a Fault/Error...WON'T SHUT OFF 1. Unplug washer or disconnect power.
5. Verify dispenser drawer is level. 2. Verify CCU operation by running a Diagnostic Test or
any cycle.
1. Check for plugged ...
User Guide - Page 90
... or disconnect power. 2. Check drain pump motor. 5. Plug in washer or reconnect power.
6. MACHINE VIBRATES
1. Unplug washer or disconnect power.
3. Plug in washer or reconnect power. 7. DISPLAY FLASHING
See Failure/Error Display Codes.
6-12 Verify CCU operation by running a Diagnostic Test or
any cycle. Remove shipping system. 2. Check drain pump. 4. PROBLEM WON'T DRAIN
POSSIBLE...
Similar Questions
No Cold Water
I have a Kenmore 2982 - 800 4.0 cu. Ft. Capacity top-load Washer bought in 2009. All of a sudden, it...
I have a Kenmore 2982 - 800 4.0 cu. Ft. Capacity top-load Washer bought in 2009. All of a sudden, it...
(Posted by jethalhuber 10 months ago)
How Can I Clean My Kennmore Washer Machine?
(Posted by Mariavargas1102 9 years ago)
Cleaning Washer
I have a Kenmore Vibration Guard front load washer. How do I clean it? I can't find the manual.
I have a Kenmore Vibration Guard front load washer. How do I clean it? I can't find the manual.
(Posted by Jduppler 9 years ago)
I Have An F21 Code...cannot Run The Washer
How do I get the water out...It wont run I have a HE5T Steam washer
How do I get the water out...It wont run I have a HE5T Steam washer
(Posted by kapszukiewicz 10 years ago)
Flashing F21 Light And Water Pooling In Washer.
I was washing a load of clothes when my washer stopped and F21 light was flashing. Clothes was soake...
I was washing a load of clothes when my washer stopped and F21 light was flashing. Clothes was soake...
(Posted by ocorona213 11 years ago)