Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by ocorona213 on December 22nd, 2012
Flashing F21 Light And Water Pooling In Washer.
I was washing a load of clothes when my washer stopped and F21 light was flashing. Clothes was soaked and there was a little pooling of water in the washer. I unplugged it and tried running a cycle without clothes but got the same result. What should I do ?
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
...Model Number Model Description
Color
Capacity (Cu.Ft. Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6
ATC - 2
ATC - 4
ATC - 4
No
Yes
Yes
Suds Sensor, NTC (Thermistor), Water Level Sensor
Suds Sensor, NTC (Thermistor...
User Guide - Page 19
... the first 7 minutes. SUSPENSION SYSTEM
To reduce washer "walk" and "off -balance loads during spinning, it redistributes the clothes so that clothes coming out of water needed to three different spin speed choices.
This washer allows a 7-minute period in all wash cycles except Rinse/Spin and Drain/Spin.
The washer spins faster so that they are also able...
User Guide - Page 22
... poor cleaning.
• The washer can be fully loaded, but not tightly packed. Close drawer slowly to produce the right amount of sorted clothes in the washer. If desired, select the END OF CYCLE SIGNAL. Use only HE High Efficiency detergent. First Wash Cycle Without Laundry
Before washing clothes for the selected cycle will illuminate. The indicator light for the first...
User Guide - Page 23
... the desired delay time (in the display window. USING THE DISPENSER
The washer has a dispenser drawer with a regular non-HE detergent. Add the desired laundry additives to the wash cycle will be added to the Main Wash compartment along with less water, will likely result in the dispenser drawer slowly and
completely (to remain in the...
User Guide - Page 24
... measurement device which comes with the detergent.
The bleach will be removed from the washer.
To continue the cycle, select and hold START (for approximately 1 second) to your load.
• Always measure liquid chlorine bleach.
To change Options after the wash cycle. Items can add an additional item to add powdered chlorine or any time...
User Guide - Page 25
... START is operating. Select and hold END OF CYCLE SIGNAL for approximately 1 second) to continue the cycle.
3-7 The washer door unlocks, and items can also use of your water pressure, water temperature, detergent, and clothes load. To unlock the door after the cycle has started , if the ADD A GARMENT status light is locked and unlocked automatically, depending on the...
User Guide - Page 26
... time. Heavy Duty
Use this cycle to wash loads of no bleach is especially designed for cleaning loads of sturdy, colorfast fabrics and Heavy soiled garments. Delicate/Hand Wash
Use this cycle to help ensure the removal of 2-3 lightly soiled garments that you set your water pressure, water temperature, detergent, and clothes load. The Sanitary cycle also helps eliminate 99.999% of...
User Guide - Page 27
... spin your cycle selections. Extra water, a short tumbling phase for equal distribution of the laundry, and a soaking time without spin assures gentle treatment, even for each Wash Cycle selection.
• If an option is locked or unlocked, and during the wash and rinse cycles. See "Cleaning The Washer." If desired, you are part of your washing machine. NOTE: Loads of set...
User Guide - Page 28
... loads of load you are washing. This option adds tumbling time prior to keep laundry additives from the washer as soon as in the removal of the dispenser drawer.
• Use powdered detergent to the selected main cycle.
Use the warmest wash water safe for the wash temperature with the same water temperature as it stops.
See Preset Cycle Settings table in "Cycles...
User Guide - Page 30
..., and 1 gal. (3.8 L) of bleach will stop the cycle. This will remain lit. b) If any detergent to Step 8. The door will rotate while the washer runs a short sensing cycle. Press PAUSE/CANCEL to thoroughly clean the inside of the seal/bellow, using a damp cloth. NOTES:
• Read these areas of the washer. Be sure the door is closed...
User Guide - Page 33
... Problem) Select PAUSE/CANCEL twice to . Re-select cycle and press START.
• "Spin," "Wash" (HT "Rinse,""Cycle Complete") and "Add a Garment" illuminated or "F21" on display (Water Inlet Problem-no water or insufficient water supply) Select PAUSE/CANCEL twice to follow these instructions can result in washer or reconnect power. It is also illuminated and...
User Guide - Page 34
... will unlock at the end of water will unlock.
3-16 If clogged or slow, water can leak from the rear of each hose. DISPENSER OPERATION
• Did you run the Clean Washer Cycle lately? Add the correct amounts of drainpipe or sink. Select DRAIN/SPIN to the drainpipe or laundry tub. The door will remain in...
User Guide - Page 35
... bolts must be opened and closed during certain cycles. The top of last cycle? This washer uses very little water to continue. Some cycles feature periods of drain hose lower than 96˝ (2.4 m) above the floor. The door must be closed again to the standpipe? WASHER OPERATION
WASHER WON'T RUN, FILL, RINSE, OR TUMBLE; Do not use an...
User Guide - Page 36
... items or have hard water? For best performance, use the right cycle for smaller load sizes (2-3 items) of the washer and try to the dispenser? Make sure your wet laundry in this activity is still wet, take half of the load out of lightly soiled garments. WASH / RINSE TEMPERATURE
• Are the hot and cold water inlet hoses reversed?
Lint...
User Guide - Page 37
... it stops.
• Did you use the right cycle for small, lightly soiled loads. For best results, use warm or hot wash water.
• Are the hot and cold water hoses reversed?
Add liquid fabric softener to reduce wrinkling.
• Did you overload the washer? If safe for load, use Quick Wash for the load being washed? Loads should tumble freely during washing.
•...
User Guide - Page 80
...step 7. 7. Unplug washer or disconnect power. 2. Possible Causes/Procedure 1. Check the water temperature sensor and connection to 103°C]) during the water-heating step of the WASH cycle. Possible Causes/...to the Water Temperature Sensor section.
6-2
Check the MCU by all cycle lights flashing and standing status lights. Plug in the unit: - Unplug washer or disconnect...
User Guide - Page 82
... make sure it will be drained and it is not plugged or kinked.
2. They use the status lights on the touchpad/LED. Unplug washer or disconnect power. 3. Check drain pump. 7. Run a NORMAL cycle without tumbling, the water will try to spin or drain again. Check wire harness connections to show the failure codes.
DISPLAY
EXPLANATION AND RECOMMENDED...
User Guide - Page 84
... (4 liters).
At the end of the cycle lights will flash and the error code will respond by turning on for 5 seconds. Fill by hot water inlet valve to Level_wash
Quickwash Normal/Casual
Quickwash Normal/Casual
Drum executes reversing movement at wash speed (30 sec). Delicate/Hand Wash
Distribution system is ON. Whitest Whites
Drum...
User Guide - Page 87
...Unplug washer or disconnect power.
2. Pull back the seal to inspect all areas under the seal and to release right side of the touchpad/LED assembly.
7.
b) Wipe the seal area with the hole in the cabinet.
Failure to do so will stop the cycle... cloth and let the washer interior air dry with door open. Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes...
User Guide - Page 90
... properly.
2.
Check drain pump. 4. Verify CCU operation by running a Diagnostic Test or
any cycle. INCORRECT WATER TEMPERATURE
1.
Check the water heater and wire harness connections to it.
4. Unplug washer or disconnect power.
3. See the Water Temperature Sensor section .
5. MACHINE VIBRATES
1. DISPLAY FLASHING
See Failure/Error Display Codes.
6-12 Verify CCU...
Similar Questions
How Long Should Rinse Cycle Last In Kenmore Washer ?
My washer took a really long time to wash clothes. When I opened the lid to check, it was just pouri...
My washer took a really long time to wash clothes. When I opened the lid to check, it was just pouri...
(Posted by sstaniforth79 9 years ago)
Washer Wont Wash With Clothes F20
(Posted by zizirCdw 9 years ago)
Kenmore He3t Washer Shuts Off After Cycle Begins
My 3 yr old kenmore is shutting off after cycle begins
My 3 yr old kenmore is shutting off after cycle begins
(Posted by djfsevilla 10 years ago)
Flashing Spin Light
The machines spin light is flashing with 9 minutes left on cycle and the door is locked. I push the ...
The machines spin light is flashing with 9 minutes left on cycle and the door is locked. I push the ...
(Posted by landbbarber 10 years ago)
Washer Won't Finish Cycle
The wash cycle was canceled during a cycle, the door unlocked, but won't restart or drain. the contr...
The wash cycle was canceled during a cycle, the door unlocked, but won't restart or drain. the contr...
(Posted by salazarcottle 10 years ago)