Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by keithborch on January 31st, 2014
My Kenmore Washer Model 417.48102 Stopped Running. Just Beeps But No Operation.
It just beeps 3 times and nothing. I think its the door switch.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 1
CONSUMER SERVICES TECHNICAL
EDUCATION GROUP PRESENTS L-78
FRONT-LOADING AUTOMATIC WASHER
MODELS: WFW8300SW, WFW8500SW, WFW8500SR
JOB AID Part No. 8178558
User Guide - Page 3
...Washer Safety 1-1 Model & Serial Number Designations 1-2 Model & Serial Number Label And Tech Sheet Locations 1-3 Specifications 1-4
INSTALLATION INFORMATION 2-1 Installation Requirements 2-1 Installation Instructions 2-6
PRODUCT OPERATION 3-1 Features And Benefits 3-1 Washer Use 3-3 Washer... Detergent Dispenser Motor 4-13 Removing The Door Switch Assembly And The Bellows 4-14 Removing ...
User Guide - Page 8
SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6
ATC - 2
ATC - 4
ATC - 4
No
Yes
Yes
Suds Sensor, NTC (Thermistor), Water Level ...
User Guide - Page 15
... that the cold water hose is seated on the washer.
2.
Damage to the corrugated drain hose. Hot water inlet C. Cold water inlet
1. Turn on the hoses for leaks. Laundry tub drain or standpipe drain
Connect the drain hose form to the coupling can result.
4. Run water through both faucets and inlet hoses, into...
User Guide - Page 22
... stops. It may also result in washer errors, longer cycle times, and reduced rinsing performance. Use only HE High Efficiency detergent. This initial cycle serves to ensure the interior is completed, the door must be marked "HE" or "High Efficiency." It is illuminated or if the cycle has been canceled.
Sort laundry according...
User Guide - Page 32
... remove the antifreeze, if used.
Reinstalling the washer
1. sual cycle. To transport the washer:
1. Do not reuse transport bolts. Plug in the upright position. Unplug the power cord.
3. Use 1/2 the manufacturer's recommended amount for a medium sized load. Failure to locate, level and connect the washer.
2. Run the washer through the Normal/Ca- Do not use an...
User Guide - Page 34
... end of the drain.
• Is the door locked and is the "Add a garment" light on some models)? Add powdered or liquid color-safe bleach directly to remove any water remaining in the fabric softener dispenser.
• Did you run the Clean Washer Cycle lately?
The washer door will unlock.
3-16 The non-High Effi...
User Guide - Page 37
.... Use the Delicate cycle or another cycle with this washer. • Are you using liquid detergent.
• Did you use Quick Wash on a large load? A hot rinse followed by spin will not operate correctly with a low spin speed to relax wrinkles? ...or hot wash water.
• Are the hot and cold water hoses reversed? Unload the washer as soon as it stops.
• Did you unload the...
User Guide - Page 39
... Tub) Basket Tub Assembly
Drive Motor
Front Interlock Switch
Not Shown: Console, Touchpad/LED Assembly, & Door Switch Assembly
Rear Interlock Switch ECO Valve Motor Control Unit
Drain Pump
4-1 COMPONENT ACCESS
This section instructs you on how to service each component inside the Duet Sport™ Front-Loading Automatic Washer.
The components and their locations are shown...
User Guide - Page 49
Remove the three hex-head screws from the door switch assembly. Remove the four hex-head screws from
the top ... Open the washer door. Close the washer door. 16. Top Screws
Retaining Wire Tension Spring
4-11
Front Panel
Bottom Screws
Continued on the retaining wire out from the unit.
12.
Screws
11. Door Switch Assembly Screws
Bellows
Retaining Wire
Door Switch Assembly
Pull ...
User Guide - Page 52
... THE DOOR SWITCH ASSEMBLY AND THE BELLOWS
6.
Open the washer door. Bellows
Door Switch Assembly Screws
Retaining Wire
Door Switch Assembly
Pull Bellows Off Lip Of
Panel
4-14 Failure to the washer. 3. Remove the lower front access panel
(see page 4-2 for the procedure). 5. Electrical Shock Hazard Disconnect power before operating.
To remove the door switch assembly...
User Guide - Page 53
... Bellows Retaining Clamp
Continued on page 4-11 for the procedure).
Bellows Retaining Clamp Screw
3 Door Switch Assembly Connectors
8. c) Pull the door switch assembly out and turn it from the washer (see the top right photo).
d) Remove the bellows retaining clamp from the door switch terminals, then remove the assembly. d) Unlock the tabs and disconnect the three wire...
User Guide - Page 75
.... Replace all parts and panels before accessing.
DOOR SWITCH
Door Switch Door Lock/ Unlock Solenoids
Refer to the indicated pins on connector DL3. Unplug washer or disconnect power. 2.
Pins 2 & 3 = 60 Ω Door Lock Solenoid - Connector DS2 At CCU
5-5 Failure to the R X 1 scale.
4. To check the door switch at DS2. To test the door switch, touch the ohmmeter test leads to pins...
User Guide - Page 80
... CCU operation by running . 4. Unplug washer or disconnect power. 3. Door switch/lock unit failure.
1. Check resistance of heating element, if present on this
model. (...times to it. 3. Check door switch/lock unit. 3.
The pressure switch is not working properly. Press PAUSE/CANCEL twice to activate.
Check the electrical connections at the water source(s) are turned on the washer...
User Guide - Page 81
... installation, verify the unit is locked for operations of the dispenser. 3.
Check/clean drain pump filter of the CCU board within the housing. - Door switch/lock unit failure.
1. NOTE: The door switch/lock unit can be sent correctly. Plug in washer or reconnect power.
5. LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE
If at the MCU is completely closed...
User Guide - Page 82
....
2. Check drain pump. 7. Some models do not have the display to the drain pump, pressure
switch, and Central Control Unit (CCU). 4. DISPLAY
EXPLANATION AND RECOMMENDED PROCEDURE
SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE)
If suds are detected continuously by running a Diagnostic Test or any detergent. Unplug washer or disconnect power. 3. Check...
User Guide - Page 85
...or completion
On key press only after rpm = 0 and door is unlocked
Distribution system is on (4 min). For model Duet Sport HT, the Heater is on during fill until ...set to start the test. MANUAL DIAGNOSTIC TEST
The washer must be empty and the control must be Checked
Door lock system
Dispenser Motor Dispenser contact Cold and Hot ... to Bypass channel. Stop motor to maximum speed.
User Guide - Page 86
... open circuit. Disconnect the wire harness from the water temperature sensor and measure the resistance of the door switch/lock unit. 4. NOTE: Be sure to perform the Diagnostic Tests before replacing the system components. Unplug washer or disconnect power. 2. Pump Motor Continuity Test
Pins 1 to 3
Results Normal = approx. 6 Ω Abnormal = Infinity
Water Temperature...
User Guide - Page 87
... front screw that uses higher water volumes in notch to do so will stop the cycle. On the right hand side behind the touchpad/LED assembly,...run to the bleach manufacturer's instructions for foreign objects.
3. Washer Maintenance Procedure
This washer has a special cycle that was covered by pressing PAUSE/CANCEL. Open door.
To remove line/interference filter:
1. Unplug washer...
User Guide - Page 89
... the touchpad twice. Check the door switch/lock unit using the diagnostics. Unplug washer or disconnect power. 3. Check water connections to confirm the touchpad/LED is plugged in washer or reconnect power. 8. Verify CCU operation by blowing air though the
part and measuring the resistance. 8. Check drain pump.
8. Verify flowmeter operation by running a Diagnostic Test or
any...
Similar Questions
He2t Washer. Model Number Rubbed Off/ Not Legible
I need the exact model number for my kemore washer the model number is not legible and I cannot orde...
I need the exact model number for my kemore washer the model number is not legible and I cannot orde...
(Posted by jwspicer 9 years ago)
Lights Flash & Beep 9 Times, Won't Start
I put some sheets into my Kenmore 48102 washer, closed the door, and the lights started flashing and...
I put some sheets into my Kenmore 48102 washer, closed the door, and the lights started flashing and...
(Posted by doriswhatley 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
Washer Does Not Come On When The Power Switch Is Depressed.
Washer does not power on. There is power to the receptacle. Unplugged and left it unplugged for an h...
Washer does not power on. There is power to the receptacle. Unplugged and left it unplugged for an h...
(Posted by stephenmarkhoward 11 years ago)
How To Use Rinse Cycle On Washer Model 110, Type 501?
How do I use rinse onbly cycle on this washer? This is not clearly shown in the manual that came w...
How do I use rinse onbly cycle on this washer? This is not clearly shown in the manual that came w...
(Posted by htevanz 12 years ago)