Kenmore 4810 Support Question
Kenmore 4810 Support Question
Find answers below for this question about Kenmore 4810 - 3.5 cu. Ft. I.E.C. High-Efficiency Washer.Need a Kenmore 4810 manual? We have 2 online manuals for this item!
Question posted by reginaharvey on November 2nd, 2012
I Replaced The Door Latch Lock On My Front Load Washer The Washer Won't Come On
I was told the door lock latch needed to be replaced. When the door latch lock was replaced the washing machine still will not come. The power cord has been tested and is good
Current Answers
Related Kenmore 4810 Manual Pages
Operating Instructions - Page 1
... wash action for the door lock to be laundered quickly, followed by 3 rinses plus an automatic extra rinse and a final spin. It will stop the washer, press Pause/Cancel twice.
10. Heavy This cycle provides 16 minutes of a high efficiency
detergent to the dispenser. ,, Detergent, bleach and fabric softener will take approximately 2-3 minutes for normally soiled loads...
Operating Instructions - Page 2
...Chlorine bleach should not be machine
dried. Extra Rinse is ...the cycle: ,, Door Lock ,, Add Garment
• Washing • Final Spin
o
U(C°ntr°l Lock) PN 134906700
(0706... loads forgotten in the washer. Then press Select to add that need to your hand washables, a hot water wash,...example, High Speed in the Normal cycle is much faster than High Speed in a regular cycle. The load will...
Operating Instructions - Page 3
... Duration ** Temperatures Cold/Cold
Warm/Cold Warm/Warm Hot/Cold Speed High Spin
Medium Spin Low Spin Hang Dry
No Spin Options Cycle Signal... Estimated cycle duration is based on factory settings and does not
include water fill times, out-of-balance or oversudsing corrections.
WASHER SETTINGS CHART
The following chart shows the temperatures, spin speeds and options available for each cycle.
Installation Instructions - Page 1
...IL 60179 U.S.A. Contents
S UBJECT Pre-lnstallation Requirements Electrical Requirements Grounding Requirements Water Supply Requirements Drain Requirements Rough-In Dimensions Location Of Your Washer Unpacking Installation Replacement Parts
PAGE
2 2 2 2 2 3 4 4-5 5-6 6
Installation and service must conform with local codes and ordinances and the latest edition of life.
- This will simpfify the...
Installation Instructions - Page 2
..., 10 psi.) Your water department can reach a 90 in. (229 cm) high standpipe. Drain capable of this washer with the National Electrical Codes, ANSI/NFPA 70 (latest edition). ELECTRICAL REQUIREMENTS
CIRCUIT- DO NOTcut off or alter the grounding prong on the power supply cord. T
BACK
24 in doubt, call a licensed electrician. PRE-INSTALLAT!ON...
Installation Instructions - Page 3
For under counter installations, no special top is required.
8 ° 5'
9! 3 )
wAteP
Za! ROUGH-IN DIMENSIONS
Power"
Cord
33 . 40
(84 8)
inches(cm)
NOTE: For pedestal installations, see additional installtion instructions included with the pedestal. et s
3 3,5
'( 85, _ )
inches (cm) For stacking installations, see ...
Installation Instructions - Page 4
... and bottom of the floor may be necessary. In an area exposed to protect the floor, lay the washer on it will come in . To ensure vibration or movement does not occur, reinforcement of door.
On carpet. Base
Shipping Plug The ambient temperature should never be solid with curtains or drapes.
3. IMPORTANT MINIMUM...
Installation Instructions - Page 5
... and install them in each end of the water valve. Tighten by hand, then tighten another 2/3 turn with the pedestal.
Washer Connections
I metal "P" clamp, 2 hose clips.
. hose clips
Zewe/ing the Washer
Excessive noise and vibration can be prevented by the packaging spacers. Keep the leveling leg extension at a minimum for the...
Installation Instructions - Page 6
...washer for water leaks and proper operation.
Cable Tie
REPLACEMENT PARTS If replacements parts are needed for your Owner's Guide before plugging the power cord into a grounded outlet. Cartons covered with
this washer...plastic bags after the washer is off at a circuit breaker/fuse box.
9.
NOTE: Check to the standpipe, inlet hose, laundry tub, etc. If your washer does not operate,...
Similar Questions
My Kenmore 48102 Front Load Washer Won't Drain
(Posted by olbi 9 years ago)
Kenmore Front Load Washer Model # Mfl31245153Drain Hose Has Come Off
I opened the drain pump filter access panel to do regular maintenance. When I opened the panel, th...
I opened the drain pump filter access panel to do regular maintenance. When I opened the panel, th...
(Posted by rsherman33587 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 11 years ago)
Dgree Of Difficulty To Take Out And Replace Front Boot On Front Loading Washer
(Posted by leonard483 12 years ago)