Husqvarna HU800H Support Question
Husqvarna HU800H Support Question
Find answers below for this question about Husqvarna HU800H.Need a Husqvarna HU800H manual? We have 2 online manuals for this item!
Question posted by cotyak on August 21st, 2017
Loud Rattle When The Mower Is Moving.
Could there be something loose in the drive system? It doesn't do it until I start moving.
Current Answers
Answer #1: Posted by Odin on August 21st, 2017 5:17 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
This is caused by a worn, bent, or loose blade, or a bent engine crankshaft. Replace the blade or tighten the blade bolt. If the problem persists, you'll have to obtain professional service. (For referral, use the contact information here--https://www.contacthelp.com/husqvarna/customer-service.)
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Husqvarna HU800H Manual Pages
Parts List - Page 3
...581 70 85-49 - - 581 70 85-31
DESCRIPTION
Spring, Torsion Nut, Hex Kit, Lawn Mower Housing Rod, Hinge Blade Adapter Blade, 22" Washer, Hardened Washer, Helical Screw, Machine, ... given in U.S. HU800H (96143009900) PRODUCT NO. 961 43 00-99
KEY PART NO. inches. 1 inch = 25.4 mm. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. HUSQVARNA ROTARY LAWN MOWER - NO.
...
Parts List - Page 5
... 1 inch = 25.4 mm. Failure to do so could be hazardous, damage your lawn mower and void your warranty. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. MODEL ... Belt Keeper Washer, Flat E-Ring 7/16 Cover, Dust, Wheel Screw, Hex Head Pawl, Drive Wheel & Tire Assembly, Rear
KEY PART NO. HU800H (96143009900) PRODUCT NO. 961 43 00-99
KEY PART NO. NO.
33 532 40 91...
Operation Manual - Page 2
...and installation of age before and while moving backwards.
• Never direct discharged....
• Stop the blade(s) when crossing gravel drives, walks, or roads.
• Never leave a...'s instructions for this symbol to prevent accidental starting . WARNING: CHILDREN CAN BE SERIOUSLY INJURED ...down and behind before operating a riding lawn mower. Children are familiar with a spark arrester...
Operation Manual - Page 3
...manufacturer's recommended parts, when necessary.
• Mower blades are subject to vibrate abnormally, stop ...
• Never run .
• Disengage the drive system, if so equipped, before refueling.
•...all nuts and bolts tight to cool before starting .
• Keep all times until fueling...offs, ditches or embankments. You could expose moving parts or allow objects to be sure of...
Operation Manual - Page 4
... NOT TO PINCH OR DAMAGE CONTROL CABLES. 1. lbs. Remove protective padding, raise upper handle section into place on your lawn mower.
• Follow the instructions under "Maintenance" and "Storage" sections of a new lawn mower. Remove loose parts included with lower ("standard") knobs.
4
LIFT UP
LIFT UP
UPPER HANDLE
UPPER HANDLE
"STAR" KNOB
FIG. 1
LOWER HANDLE...
Operation Manual - Page 5
...See Fig. 3)
1. Slip vinyl bindings over frame.
Loosen T-knob. 2. Hold control bar against upper handle. 3. To convert mower to be used as a mulcher. Put grass catcher frame into loop of this manual.
5 NOTE: If vinyl bindings are ...
FIG. 3
FRAME OPENING
ENGINE STARTER ROPE
FIG. 4
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to bagging or discharging, see "TO CONVERT...
Operation Manual - Page 6
... the handle to the safety standards of the American National Standards Institute and the U.S. MULCHER DOOR - DRIVE CONTROL LEVERS - MULCHER DOOR
MUFFLER
SPARK PLUG
MEETS CPSC SAFETY REQUIREMENTS
Our rotary walk-behind power lawn mowers conform to start the blade. Release to 10% ethanol (E10) is acceptable for use of various controls and adjustments...
Operation Manual - Page 7
... the drive control housing to start and operate the mower. The further toward the rear. Hold operator presence control bar down to the handle and pulling either the operator presence control bar or a drive control lever are adjusted by holding the operator presence control bar down against handle to desired position.
To raise mower, move the...
Operation Manual - Page 8
... BAG BRACKET
GRASS CATCHER
HANDLE
GRASS CATCHER FRAME HOOK
FIG. 7
UNLOCK LATCH
OPEN MULCHER DOOR
INSTALL DISCHARGE DEFLECTOR
SIMPLE STEPS TO REMEMBER WHEN CONVERTING YOUR LAWN MOWER
FOR MULCHING 1. Mulcher door closed and locked. Mulcher door closed and locked. FOR SIDE DISCHARGING 1. To convert to bagging or discharging:
REAR BAGGING (See Fig...
Operation Manual - Page 9
...season. ADD GASOLINE (See Fig. 10)
• Fill fuel tank to change the oil more often under lawn
mower handle. 3. Purchase fuel in the Maintenance section of this manual.
Do not store, spill or use , see...initial use of tank filler neck. Empty the gas tank, start the engine and let it run until blade and all moving parts have stopped and turn fuel valve to OFF position if you do...
Operation Manual - Page 10
...the engine speed should be set in the fast position. • Pores in size so that the lawn mower cuts off with the mulching action. This will help engine air flow and extend engine life. ...grass and grass conditions may be exposed to direct sunlight. • For best results, adjust the lawn mower cutting height so that as very tall grass, it will be necessary to raise the height of...
Operation Manual - Page 11
...HOURS
BEFORE STORAGE
Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** ...Start mowers
*** Power-Propelled mowers
****
Use a scraper to clean under a heavy load or in high outdoor temperatures. 2 - To receive full value from the warranty, operator must maintain mower...
Operation Manual - Page 12
...-clockwise.
5. Turn lawn mower on to clean the drive wheels, check both rear wheels. If blade is hazardous, could damage your mower and void your mower is balanced, it cannot come in a horizontal position.
Install debris shield.
3.
DRIVE WHEELS
Check rear drive wheels each time you will cause eventual damage to be sure they move freely. If necessary...
Operation Manual - Page 13
... the drive should check your engine oil level frequently to the proper level at surface. DO NOT thread the cap into the engine. 6. Check the crankcase oil level before starting in...is not used .
• Check your expected operating temperature. Wait one year.
Tip lawn mower on the tube. LUBRICATION
Use only high quality detergent oil rated with oil.
Clean by ...
Operation Manual - Page 14
.... Start engine (as described in contact with putty knife or similar tool to remove any build-up of cut grass or another hard surface.
HOSE
CAUTION: Disconnect spark plug wire from accumulating.
Shut off the engine. 7. SLOT
TAB
CARTRIDIGE
FILTER COVER
CLEAN UNDER DRIVE COVER
Clean under drive cover at the fitting. Move lawn mower...
Operation Manual - Page 15
...ector, attached between the rear wheels of your lawn mower has three (3) height positions - IDLER PULLEY
BELT RETAINER
DEBRIS SHIELD
TO REMOVE DRIVE BELT (See Fig. 19)
1. Remove rear...Remove drive belt.
SERVICE AND ADJUSTMENTS
CAUTION: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:
1. Make sure the blade and all moving parts have completely stopped.
3. Return mower ...
Operation Manual - Page 16
... done at the end of this manual).
2.
LAWN MOWER
When lawn mower is not adjustable. Lubricate as shown in the ...Maintenance section of the season or if the unit will not be used for a period of the lower handle and pivot entire handle assembly forward and allow handle to fold down to be stored for 30 days or more. Inspect moving...
Operation Manual - Page 17
... CYLINDER
1. Bad spark plug.
6. CAUTION: Never store the lawn mower with clean engine oil. (See "ENGINE" in your gasoline will... fuel gum deposits during storage. PROBLEM
CAUSE
CORRECTION
Does not start
1. Weak battery (if equipped).
11. OTHER
•... in OFF position. 10. Loose blade or broken blade adapter.
7. IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND EXHAUST AREAS ...
Operation Manual - Page 18
... vibration
1. "Loose" drive control system.
1. Rear of lawn mower housing one (1)
setting higher. 3. Dirty air filter. 4. Clean/replace air filter. 4. Check oil level. 6.
Replace blade. Set all wheels at slower walking speed. Bent engine crankshaft.
1. Tighten blade bolt. 2. Bent engine crankshaft.
3. Replace blade adapter. 4. Move lawn mower to a Husqvarna...
Operation Manual - Page 21
...*
*
Pump
2 Years
Other Non-Expendable Components
2 Years
All other than Rental Use)
Riding Lawn Tractors:
Frame, Chassis, Front Axle
5 Years
No Warranty
Engine*
*
*
Transmission (if made...1 Year Pro-rated
No Warranty No Warranty No Warranty
Other Non-Expendable Components Residential Zero Turn Mowers ( RZ Only )
3 Years
No Warranty
Engine*
*
*
Transmission **
**
No Warranty...
Similar Questions
Snow Blower On R 322 Awd
Takes way to much strength to life both mower in summer and now snow blower in winter. Something not...
Takes way to much strength to life both mower in summer and now snow blower in winter. Something not...
(Posted by ianshirley 3 years ago)
Rz4623 Replaced Belt, Now My Mower Runs But Moves Very Weak. Not Much Power
I replaced the belts and now my mower is not moving with the power that it once had. Will hardly mak...
I replaced the belts and now my mower is not moving with the power that it once had. Will hardly mak...
(Posted by Mey98 7 years ago)
Loud Rattle Or Vibration.
I have a loud rattle or vibration only when my mower is moving. Any idea what is loose or rattling a...
I have a loud rattle or vibration only when my mower is moving. Any idea what is loose or rattling a...
(Posted by cotyak 8 years ago)
Husqvarna Cth180
This mower came with my new property, it starts fine but when I pull out the button on the left hand...
This mower came with my new property, it starts fine but when I pull out the button on the left hand...
(Posted by nicola17 9 years ago)