Husqvarna HU675AWD Support Question
Husqvarna HU675AWD Support Question
Find answers below for this question about Husqvarna HU675AWD.Need a Husqvarna HU675AWD manual? We have 2 online manuals for this item!
Question posted by Hayesbadboy96 on May 27th, 2023
Hu675awd Husqvarna Blade Not Turning Freely
my pullstart works fine but crankshaft is hard to turn ? Hel
Current Answers
Answer #1: Posted by hzplj9 on May 27th, 2023 12:09 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,875,690
Member since:
June 25th, 2012 Points: 4,875,690
The blade is driven directly from the crankshaft of the engine. It therefore shows you have an engine drive problem. Remove the blade and see if it runs OK. If that is OK the recheck the fitting of the blade. Have you checked the oil or have you replaced it at all? Old oil could stop the engine turning due to lack of lubrication. The oil becomes like a jelly and slows down the engine.
Refer to the troubleshooting info and service requirements in the user manual available here.
https://www.manualslib.com/manual/713558/Husqvarna-Hu675awd.html
Hope that solves your problem. Please mark as helpful if it leads you to a satisfactory solution.Thank you.
Answer #2: Posted by SonuKumar on May 28th, 2023 8:14 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,633,680
Member since:
May 9th, 2021 Points: 16,633,680
If the blade on your Husqvarna HU675AWD lawn mower is not turning freely, there are a few potential causes and troubleshooting steps you can try:
- Debris or obstruction: Inspect the blade and the area around it for any debris, such as grass clippings, sticks, or other objects that may be obstructing the blade's movement. Remove any debris carefully and ensure that the blade path is clear.
- Bent or damaged blade: Examine the blade for any signs of bending, damage, or excessive wear. A bent or damaged blade can cause it to bind or not spin freely. If the blade is bent or damaged, it should be replaced with a new one following the manufacturer's recommendations.
- Loose or damaged blade adapter: Check the blade adapter, which connects the blade to the engine shaft. Ensure that it is securely tightened and properly aligned. If the blade adapter is damaged or worn, it should be replaced.
- Worn or seized bearings: The blade's movement relies on the bearings in the blade spindle assembly. Over time, these bearings can wear out or become seized, causing the blade to not turn freely. If the bearings are worn or seized, they should be replaced.
- Drive belt tension: Check the tension of the drive belt that connects the engine to the blade. A loose or improperly tensioned drive belt can cause the blade to not spin freely. Consult the mower's manual for instructions on how to adjust the drive belt tension properly.
- Mechanical issues: If none of the above steps resolve the issue, there may be a more significant mechanical problem with the mower, such as a damaged or misaligned pulley, a worn engine clutch, or an issue with the transmission. In such cases, it is recommended to consult a qualified technician or contact Husqvarna's customer support for further assistance.
Always prioritize safety when working on or near the blade. Ensure the mower is turned off, and the spark plug wire is disconnected before attempting any maintenance or repairs.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Husqvarna HU675AWD Manual Pages
Owners Manual - Page 2
...which could be maintained in effective working order by the manufacturer.
• Stop the blade(s) when crossing gravel drives, walks...to vibrate abnormally, stop before operating a riding lawn mower. WARNING: This lawn mower is clear of age before removing grass catcher....responsible adult.
• Be alert and turn machine off and wait until the blade comes to operate the machine.
•...
Owners Manual - Page 3
...wire, and keep equipment in maintaining, caring for and using your lawn mower properly.
Always place containers on other debris build-up.
GENERAL ...blade attachement bolts, tight and keep wire away from your nearest authorized service center/department. SERIAL NUMBER
DATE OF PURCHASE
THE MODELAND SERIAL NUMBERS WILL BE FOUND ON ADECALATTACHED TO THE REAR OF THE LAWN MOWER...
Owners Manual - Page 4
...section into place on lower handle and tighten both upper ("star") knobs.
4. TO REMOVE LAWN MOWER FROM CARTON
1. Remove all parts and hardware you attempt to operating position and align holes in...such as necessary to "ADJUST HANDLE" in the Service andAdjustments section of your lawn mower, all packing materials except padding between upper and lower handle and padding holding ...
Owners Manual - Page 5
... GUIDE
T-KNOB
ENGINE STARTER ROPE
FIG. 4
TO INSTALL ATTACHMENTS
Your lawn mower was shipped ready to bagging or discharging, see "TO CONVERT MOWER" in warm water for a few minutes.
NOTE: If vinyl bindings...in the Operation section of rope guide.
4. Hold control bar against upper handle.
3. To convert mower to be used as a mulcher. Slip vinyl bindings over frame. If bag gets wet, let ...
Owners Manual - Page 6
... this manual for starting the engine. NOTE: Gasoline containing up to start the engine. MEETS CPSC SAFETY REQUIREMENTS
Husqvarna rotary walk-behind power lawn mowers conform to stop
the engine.
6
STARTER HANDLE - WARNING: The blade turns when the engine is shipped WITHOUT OIL OR GASOLINE in literature supplied with the location of any gasoline exceeding...
Owners Manual - Page 7
... is a small "gap" between the plate tabs. Operate mower to defeat the function of blade contact injury. If condition fails to minimize the risk of the operator control. The blade turns when the engine is running.
• Your lawn mower is worn and should be positioned behind the mower handle to the handle. Proceed as required. Move...
Owners Manual - Page 8
...Add oil if needed. Use fresh, clean, regular unleaded gasoline with gasoline.
OPERATION
TO CONVERT MOWER
Your lawn mower was shipped ready to be used as a mulcher.
Slowly pour the entire container down the...Insert and tighten dipstick. Purchase fuel in the Maintenance section of the lawn mower and place the grass
catcher frame hooks onto the grass bag brackets. • To...
Owners Manual - Page 9
... raise the height of cut area will not be exposed to direct sunlight. • For best results, adjust the lawn mower cutting height so that the lawn mower cuts off with your highest engine (blade) speed as this will disperse into the grass and not be noticed. This will help prevent matting and graining of...
Owners Manual - Page 10
... OR SEASON HOURS
BEFORE STORAGE
Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery **
Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug...
Owners Manual - Page 11
... the engine.
5. Be sure the trailing edge of your hands with gloves and/or wrap blade with a file or on a grind- Turn lawn mower on the engine crankshaft. FIG. 12
TO SHARPEN BLADE (See Fig. 13) NOTE: We do not turn freely, contact a qualified service center.
2.
and that may cause tire damage. TIRES
• Keep...
Owners Manual - Page 12
... case. TO CHANGE ENGINE OIL (See Fig. 14)
NOTE: Before tipping lawn mower to your drive system working properly, the gear cases and area around the drive should remain in one year. Disconnect spark plug wire from lawn mower or side of the blade moves downward, sharpen the heavy end until fuel tank is balanced. Remove...
Owners Manual - Page 13
...plug type and gap setting are covered to keep trash from beneath the mower housing during the washout process.
6. Turn on water supply and check for a full minute to remove excess water...of this manual) and let engine run until the underside of cut grass or another
hard surface. Move lawn mower to carburetor, replacement is equipped with arrow pointing towards carburetor.
3. NOTE: Water,...
Owners Manual - Page 14
... that objects will be replaced. Remove debris shield.
4. Remove drive cover.
Turn lawn mower on its side with plug.
SERVICE AND ADJUSTMENTS
CAUTION: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Release control bar and stop engine. 2. Make sure the blade and all moving parts have completely stopped. 3.
REAR DEFLECTOR
The rear...
Owners Manual - Page 16
... NEEDS ADJUSTING, CONTACTYOUR NEARESTAUTHORIZED SERVICE CENTER, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS. LAWN MOWER
When lawn mower is running too fast or too slow, take your lawn mower has three (3) height positions - Touch up your lawn mower to an authorized service center for storage.
1. IMPORTANT: WHEN FOLDING THE HANDLE FOR STORAGE OR TRANSPORTATION...
Owners Manual - Page 17
... ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE.
CYLINDER
1.
IMPORTANT: NEVER COVER MOWER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM. CAUTION: Never store the lawn mower with new spark plug. Add stabilizer to rust.
Pull starter handle slowly a few times to reach the carburetor. OTHER...
Owners Manual - Page 18
...crankshaft.
1. Starter rope hard to engine. Move lawn mower to cut - not filling
2. Lift on when control bar is on blade worn off of pulley. 3. Raise rear of lawn mower housing or cutting blade....
10. Turn fuel valve lever to push
1. Cut at same height. 3. Grass catcher 1. Clean/replace air filter.
2. Worn, bent or loose blade. 2. Replace blade adapter. ...
Owners Manual - Page 20
..., bearings, blades, rods, height adjusters, caster/anti scalp wheels etc... Authorized Husqvarna Servicing Dealer/Center. Should you to register your product online at www.husqvarna.com.
11. Husqvarna encourages you ...or visit www.husqvarna.com. are for pick-up , pre-delivery service or repair service by way of the following are NOT covered:
(a) Abrasion to mower decks, including sand...
Owners Manual - Page 21
... shell. stamped deck shell. Limited Lifetime Warranty Battery
Other Non-Expendable Components Residential Zero Turn Mowers ( MZ & EZ )
Engine* Transmission **
MZ5424S & MZ5425S (967003901 & 25021)...
All other than Rental Use)
Riding Lawn Tractors:
Frame, Chassis, Front Axle
5 Years
No Warranty
Engine*
*
*
Transmission (if made by Husqvarna/Peerless)
3 Years
No Warranty
Transmission ...
Parts List - Page 3
...87-01 115 581 33 00-01 - - 115 66 18-96
DESCRIPTION
Screw, Dogpoint 3/8-16 x 1-1/8 Kit, Lawn Mower Housing Blade Adapter Blade, 22" Washer, Hardened Washer, Helical Bolt, Hex Head, Grade 8 3/8-24 x 1-3/8 Front Baffle Screw...Use only Original Equipment Manufacturer (O.E.M.) replacement parts. MODEL NO. HU675AWD (96143010801) PRODUCT NO. 961 43 01-08
KEY PART NO. HUSQVARNA ROTARY LAWN MOWER -
Parts List - Page 5
HUSQVARNA ROTARY LAWN MOWER - Failure to do so could be hazardous, damage your lawn mower and void your warranty. NO.
1 586 03 33-01
2 586 07 ... Screw, Hex Head 1/4-20 Mounting Bracket, Debris Shield Belt Keeper, Gearcase, Rear Washer, Flat
KEY PART NO. HU675AWD (96143010801) PRODUCT NO. 961 43 01-08
KEY PART NO. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement ...
Similar Questions
Husqvarna Riding Lawn Mower Starts, Blade Spins, Won't Go Forward Nor Reverse
(Posted by shywolfalways82 3 years ago)
My Awd Doesn't Work Should There Be A Cover On The Awd Above The Blades
(Posted by Dskradis 5 years ago)
Mower Will Not Start. Has Not Been Used Since October
(Posted by rweaver58421 8 years ago)
Blades Turn Slowly
I have a husqvarna mz 5225 while cutting the blades will stop turning and then speed up cutting and ...
I have a husqvarna mz 5225 while cutting the blades will stop turning and then speed up cutting and ...
(Posted by ewhite7748 9 years ago)