Husqvarna 316EL Support Question
Husqvarna 316EL Support Question
Find answers below for this question about Husqvarna 316EL.Need a Husqvarna 316EL manual? We have 2 online manuals for this item!
Question posted by blebon on February 26th, 2014
Husky 316e. No Oil To Bar
no oil to bar. cleaned it all out. ran it. couldn't see any oil coming out of the oil hole before the bar. clog? pump? do you need special tools to open it up? can't see the screw type down the small screw hole. thanx
Current Answers
Related Husqvarna 316EL Manual Pages
Owners Manual - Page 3
... reached the chain.
IMPORTANT -
Index
Safety Precautions 4-6 General safety 7 Introduction 8-10 User Explanation 11 Technical specification 11 Mounting guide bar and chain 12 Chain oil 12 Before each use with a 120V AC power supply. Hazards or unsafe practices which could result in product or property damage. WARNING -
Always pull out ...
Owners Manual - Page 4
... Do not let guide bar tip come into contact with any object...without triggering brake, for the bar and chain combination on the label. Recommended cutting equipment in this example: • Bar length: MAX16 inches •...hearing protection • face protector or goggles
WARNING! MAX 400
Maximum permissible bar length. Read All Instuctions Read and understand the Operator's Manual before using...
Owners Manual - Page 5
...• Tip contact can reduce or eliminate the element of the guide bar come into the cutter.
Reduced-Kickback Guide Bar, designed with a bow guide is potentially very dangerous. Low-Kickback Saw ... use any other combination of chain and guide bar which you reduce kickback and maintain control of the saw equipped with a small radius tip which has met the kickback performance ...
Owners Manual - Page 6
...bar to your electric chain saw, use .
20. Wearprotective hair covering to the environment of the work area well lit. Do not start cutting until you have received specialized...all service on the nameplate of oil. 13. Dress properly. Rubber gloves...an approved outdoor type and should not be alert for ... Keep the handles dry, clean and free of the tool.
22. Do not use...
Owners Manual - Page 7
... disorders or abnormal swellings. Heavy enough (see your Authorized Service Dealer for outdoor use a unit with any way. Vibrations from heat, oil, and sharp edges. Users who operate power tools on the name plate of cable (ft.)
25
50
Wire gauge
14
14
Cable longer then 50 feet in a polarized outlet. If...
Owners Manual - Page 12
...chain brake 14. Clutch cover 15. Rear handle 3. Front support handle 7. Oil level window 9. Guide bar 12. which is double insulated and manufactured in the event of the chain jumping... Frequency Rated Current Overload protection
Weight
Without bar and chain With 14" bar and chain
Chain lubrication
Oil tank capacity Oil pump
Chain/bar
Recommended bar lengths
Chain speed unloaded Chain speed at ...
Owners Manual - Page 13
... chain is in damage to the chain, bar and oil pump.
• It is drawn
snugly against the drive sprocket at a 45° angle to use oil of the bar, but the chain may still be used.
• Never use special chain oil with the combination wrench. Tighten adjustment screw until the chain has been broken in. Hold...
Owners Manual - Page 14
...; Drain the oil tank before fitting...bar and chain closer to activate the chain brake if your tool...tool cable to carry the current your right hand is recommended. Cable insulation
must be intact, with no unintended contact with your right hand on the rear handle and your extension cable is undamaged and operating properly (see page 15). • Check right hand-guard for loose screws...
Owners Manual - Page 16
...chain stops frequently while cutting, it from the brake. ENGLISH
Testing and maintenance of the guide bar hits the trunk, the brake should stop and sharpen the chain.
14
Ease up on the ...checked several times daily.
Follow all maintenance instructions carefully. If necessary, clean resin and chips from overload. Then activate the chain brake by turning your left hand on the...
Owners Manual - Page 17
Check that the oil hole in good condition. • Check that the bar and chain are some general maintenance instructions. Replace if ...should be replaced.
• Clean the chain brake and check that it is correctly tensioned and in the bar is needed to clean the clutch after extended use.
ENGLISH
Maintenance
Tools and materials
The tools and materials shown are absolutely ...
Owners Manual - Page 18
... may be considered to a rotational kickback impulse. We recommend that you may be considered to have equivalent kickback energy. Model
Guide bar
Saw chain
Length inch
Pitch inch
Max nose radius
Type
CKA W/O
CKA W
316 El
12
3/8
7T
14
3/8
7T
16
3/8
7T
Husqvarna H37 26°
22°
Husqvarna H37 29°...
Owners Manual - Page 19
...jump off the bar and cause injury. After the saw . Change drive sprocket each time a new chain is also the most frequent cause of the low-kickback type, and that ...never be visible signs of rotation. Clean bar groove and oil hole regularly.
Check daily for 1/2 - 1 minute there should be pulled easily by pulling the chain in the normal direction of oil spatter on side links and cutting ...
Owners Manual - Page 20
...dangerous to use . Depth gauges are needed on each chain has a specific cutting...each tooth. Filing too deep or using a depth gauge tool
(for others the file is done with the handle low...file which does not cut with a marked filing angle. Approved bar / chain combinations
L
1 5
inch
inch/mm inch/mm...that for some chains, the file is too small will make a chain dangerously aggressive. A ...
Owners Manual - Page 21
...back at you . However, a kickback can also be a lightning fast reverse reaction kicking the guide bar back at you .
19 When the chain gets blocked and stops, the reaction will severely cut ...! Kickback is kickback ? As a result, the chain might grab or jam. If you are small. It can be very powerful.
ENGLISH
General Working Instructions
What is the sudden, rearward jerk of ...
Owners Manual - Page 22
...check that you . If the chain brake does not activate, clean it will be reset by your wrist only after each work...chain brake is triggered when the hand guard is important that you need it , the force may not always activate during a kickback. ... recommend that the mechanism is designed to reduce
the severity of the bar. • Avoid unsafe positions. • Use proper grip. &#...
Owners Manual - Page 23
...come up and back at you.
2. Pinching the saw chain along the top of the guide bar may occur.
2
Direction of the bar. ENGLISH
General Working Instructions
Pinch Kickback
1
1.
IMPORTANT!
• Kickback can only occur if the kickback danger zone of the bar... touches an object.
• A kickback can be lightning fast.
• Although most kickbacks are small, a kickback...
Owners Manual - Page 24
... on the tip of obstructions. • Stay alert. Do not let the nose of the guide bar come into contact with logs, branches or other common hazards associated with that the work area is free of the... bar is in close proximity to the cut.
22
Proper working techniques The only way to avoid ...
Owners Manual - Page 25
...the chain if the kickback starts from a ladder, in a tree or in these positions, and with the bar closer to keep a good, firm grip on the front handle.
Cut only one hand. NOTE! Do not....
23 Remove the pieces you less control of wood. Never use your face / upper body, even a small kickback may not have cut are left handed: Your electric chain saw is harder to reach you . front ...
Owners Manual - Page 26
... protection that a severe kickback will provide their intended protection only if the chain is sharpened and maintained according to replace your saw.
• Use small nose radius bar and low-kickback saw chain has been designed to reduce the likelihood of kickback, If the chain is that the original equipment.
24
This...
Owners Manual - Page 27
... agent or local foresty schools for holes and ditches.
4. Be extremely cautious... will pull the saw away from one place to engage the tip of the bar, a kickback may vary depending on obstacles, such as dense fog, heavy rain...saw , the energy used to work safer.
2. Avoid stumbling on the terrain, vegetation, type of wood, form and size of kickback.
25 Watch out for advice on slopes or ...
Similar Questions
359 Oiler
I 'have a 359 that is not getting enough oil on the bar. I have taken all componets apart and cleane...
I 'have a 359 that is not getting enough oil on the bar. I have taken all componets apart and cleane...
(Posted by hayman17 9 years ago)