Husqvarna SC18 Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna SC18 manuals!
Problems with Husqvarna SC18?
Ask a Question
Free Husqvarna SC18 manuals!
Problems with Husqvarna SC18?
Ask a Question
Most Recent Husqvarna SC18 Questions
Popular Husqvarna SC18 Manual Pages
Owners Manual - Page 1
Models:
SC18/968981201 SC18/968999352
MANUAL NO. 540200156 REV. 01 (12/01/05) Operators manual
Please read these instructions carefully and make sure you understand them before using the machine.
Owners Manual - Page 2
...
Engine -
Index
CONTENTS
Operator's Guide Page
Specifications 2 Features and Controls 3 General Operating Instructions 4 Warnings ...4
Operating Instructions Page
Operator's Tips 4 Operating on Hills 5 Before You Start 5 Transporting 5 Sod Cutting 5
Maintenance and Service Instructions Page
Safety and Maintenance 6 Safety ...6 Engine Service and Warranty 6 Lubrication Schedule...
Owners Manual - Page 3
...need to your engine manual for oil type, viscosity, weight
and capacity. There is located directly behind the front axle
underneath the engine.
3. Refer to service the transmission. Oil ...used in the Clutch/Gear Box 1. FEATURES AND CONTROLS
Oil used in the engine (gray cap) 1.
Refer to your servicing dealer if needed.
...
Owners Manual - Page 4
...or Husqvarna if ...parts. • Do not run engine in severe injury or death. machine.
Doing so without our written permission may be avoided, such as you in the safe operation and proper maintenance of the sod...servicing. CAUTION: indicates unsafe actions or situations that may cause injury and/or minor equipment or property damage. OPERATING INSTRUCTIONS
GENERAL INFORMATION This manual...
Owners Manual - Page 5
...throttle to set depth of the ground. 2. BEFORE YOU START • Read and understand this manual. &#...blade engagement lever forward to absorb the moisture. SOD CUTTING See Figure - OPERATING INSTRUCTIONS
• Do not attempt sharp turns while ...Position the sod cutter at engine manufacturer's recommended level. (Refer to engine
manufacturer's manual.) • Put the sod cutter into the ...
Owners Manual - Page 6
...instructions. DO NOT tear down the engine, as this may be made with the engine during the warranty period, take it to an Authorized Service Dealer.
TWO MINUTE WARNING Sod Cutters may void the Engine Manufacturer's Warranty. CAUTION Husqvarna parts...Item
Lubricant
• Engine Oil, see engine
owner's manual
• Chain 30W Motor oil or
Chain lubricant
• Linkage 30W oil
&#...
Owners Manual - Page 7
... 1/4" ( 6mm) at
mid span. • Install chain guard. • Set sod cutter back to inhibit rust. 6. STORAGE 1. SERVICE AND MAINTENANCE
BLADE WEAR Sod cutter blades may wear quickly depending on these items. DO...washing will prolong the service of your machine. Replace blade when worn to engine manufacturer's instructions for engine storage information. 2. Refer to 1 1/2" (3.8cm) or ...
Owners Manual - Page 8
...has a Skid Pan installed. 3. See
Technical Bulletin Throttle Cable Adjustment.
5. What RPM should my engine be damaged). 5. Be sure the maximum RPM is set to?
1. 3000 ...Springs are installed.
(Springs have 1.5-inch OD.)
4. Ensure debris is splined and snap-ringed in the Transmission Chain or wrapped around the transmission output shaft.
2. PROBLEM
TROUBLESHOOTING
ANSWER/COMMENT
...
Owners Manual - Page 9
... snap-ringed in place. 1. PROBLEM
TROUBLESHOOTING
ANSWER/COMMENT
Chain (Drive) is coming off before checking
clearance of blades from the cutting edge to slip.
Moisture, oil or grease on its rear wheels while cutting can be off .
1. Note:Gear box pulley has double set screws) to 1 1/2" from outside only. Replace when worn to the...
Owners Manual - Page 10
... the gap to 2 1/2". 2. Set to slip. Limit maximum depth of pulley. If the Blade Lift Springs are installed.
(Springs have 1.5 inch OD.) 3. Be sure the correct Husqvarna belt is out of cut too deeply, which causes the belt to 3000 RPM See Technical Bulletin "Throttle Cable Adjustment."
2. If not, replace with the blade engaged...
Owners Manual - Page 11
...
or servicing dealer.
1. Steam cleaning machines without lubricating threads afterwards will cause rust resulting in neutral - Put in locked threads.
2. Remove bolt. 3. Tire wear ...Bulletin "Inspection Procedure for 1/8" to tighten bolts Bolts breaking Tires wearing too quickly
TROUBLESHOOTING
ANSWER/COMMENT
10. PROBLEM Belt glazed or slipping
Depth Control Rod broke Depth Control...
Husqvarna SC18 Reviews
We have not received any reviews for Husqvarna yet.