Hunter 23980 Support Question
Hunter 23980 Support Question
Find answers below for this question about Hunter 23980.Need a Hunter 23980 manual? We have 4 online manuals for this item!
Question posted by ps60303 on June 2nd, 2014
I Need An Integrated Receiver Part # Cei016283
The person who posted this question about this Hunter product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hunter 23980 Manual Pages
Installation Guide - Page 1
.... Step 5
Step 5 Prepare the Wiring
5-1. Tools and Supplies You May Need
• Drill • Keyhole saw • 2' x 4' support brace • UL-approved octagonal
4" x 1-1/2" outlet box
• Two #8 x 1-1/2" wood screws and washers
• Approved connector for electrical wire
Checklist for Existing Fan Site
If you cannot lock the circuit breakers in accordance with...
Owner's Manual - Page 2
... before beginning installation. If you are proud of our work. Never insert foreign objects between rotating fan blades. • To reduce the risk of fire, electrical shock, or motor damage, do...; Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to the service panel. • All wiring ...
Owner's Manual - Page 3
.... e steps in one of three ways, depending on ceiling height and your Hunter fan, use only Hunter speed controls. To install and use sturdy 3/4" diameter pipe to the... high
For ceilings higher than 8 feet, you maximum installation flexibility and ease.
All Hunter fans use the accessories, follow the instructions included with each product. You can purchase Hunter extension ...
Owner's Manual - Page 4
... (if applicable) in the pullout sheet called "Preparing the Fan Site."
Refer to the motor or fan blades. Check for any parts are essential for safety, reliable operation, maximum efficiency, and energy savings. Gathering the Tools
You will need help installing the fan, your Hunter fan dealer can do the following tools for and install...
Owner's Manual - Page 5
... down through the hole in the middle of the two 3" wood screws.
2-5. Hunter Fan Company
Position the isolators between the ceiling plate and ceiling by turning off position, securely fasten... • Installing the Ceiling Plate
CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by inserting the raised areas on each isolator into the holes in the...
Owner's Manual - Page 6
... through the downrod.
3-3. Place the low profile washer into the canopy. Low Profile Screw
Ceiling Plate Tabs
Step 3-7
Hunter Fan Company
Canopy Slots
42405-01 • 01/20/06 Raise the fan and align the slots in the washer with three low profile screws.
3-7.
Be sure the green ground wire is normal...
Owner's Manual - Page 7
... unfamiliar with national and local electrical codes. 4-1. Make sure the power to the black wire from the fan 4-2. CAUTION: Be sure no bare wire or wire strands are not included. Push all wires and wire... nuts into the outlet box.
4 • Wiring the Fan
Wire Nut Single Switch Wiring
7
42405-01 • 01/20/06
Hunter Fan Company Connect the wires as follows:
• e bare or...
Owner's Manual - Page 8
... screw holes with the mounting holes on the ceiling plate.
5-3. Securely tighten both screws.
8
Step 5-3
Step 5-4
Hunter Fan Company
42405-01 • 01/20/06
Partially install a canopy screw into the hole between the two ceiling plate tabs.....
5-4. 5 • Installing the Canopy
Step 5-1 Tab
Groove Step 5-2
5-1. WARNING: Failure to complete this step could cause fan to fall.
5-2.
Owner's Manual - Page 9
... mounting screw, then securely tighten both mounting screws. If you used grommets, the blades may include blade grommets. Your fan may appear slightly loose after screws are installed in the motor to the fan).
6-1.
Use with grommet
Blade Assembly Steps 6-1 - 6-2 Screws
6 • Assembling the Blades
Step 6-1 (Detail)
Grommet
9
Use without grommet Blade...
Owner's Manual - Page 10
... the upper switch housing.
Align the side screw holes in the housing with three housing assembly screws. Lower Switch Housing
Housing Assembly Screw
Steps 7-5 - 7-6
Hunter Fan Company
42405-01 • 01/20/06 Make sure the connectors are firmly situated in the lower switch housing assembly. To attach the lower switch...
Owner's Manual - Page 11
... the opposite position. Slide the reversing switch on electrical power to the fan.
8-2. e fan pull chain controls power to the fan. e pull chain has four settings in sequence: High, Medium...light pull chain controls power to cool the room with a furniture polishing cloth. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in the same manner as they...
Owner's Manual - Page 12
...ensure that the hanger ball is cracked. If so, replace all the blades. Turn power off, support fan very carefully, and check that the switch is on , replace fuse, or reset breaker. 2. Check ...the plug connection in the switch housing. 4.
Remove the shipping bumpers. fan does not move. 1. If you need parts or service assistance, please call 888-830-1326 or visit us at our...
Parts Guide - Page 1
...Shooting guide in the box. Call your records and warranty assistance. Before installing your fan, record the following information for your Local Service Center. 3. Call Technical Support at...1326.
Date Purchased Where Purchased
Missing / Broken Parts: Call 1-888-830-1326
3 Canopy
Fan does not work: 1. Fan Parts (Not Drawn to Scale)
65 Wood Screw
71 Mounting Isolator
64 Wood Screw
66 ...
Parts Guide - Page 2
Dwg. #
Finish Qnty
1 1 1 1 1 1 2 2 2 4 2 3 1 1 1 11 2 1 15 15 3 4 3 1
23980 94956-01 Provencial gold
Part #
74090-02-232 92697-01-298 74229-03-298 03006-06-247 74984-01-232 74510-22-247 06512-01-...
Similar Questions
I Need Rubber Grommets For A Model 28681 To Secure Blades.
I need the rubber grommets for model 28681 to secure the blades.
I need the rubber grommets for model 28681 to secure the blades.
(Posted by mgregan05 3 years ago)
Need To Replace The Fan Module
the chain has pulled out of the fan switch module I need to find a replacement module fo it. I can't...
the chain has pulled out of the fan switch module I need to find a replacement module fo it. I can't...
(Posted by Buchwaltercarole 5 years ago)
Who Sells Hunter Remote Ceiling Fan Parts?
I need a remote receiver and transmitter p/n's 85112-02-000 & 85095-01-000. Fan model is 23457. Forg...
I need a remote receiver and transmitter p/n's 85112-02-000 & 85095-01-000. Fan model is 23457. Forg...
(Posted by cmdrsonny 10 years ago)
