Hunter 22710 Support Question
Hunter 22710 Support Question
Find answers below for this question about Hunter 22710.Need a Hunter 22710 manual? We have 4 online manuals for this item!
Question posted by micsat on June 10th, 2012
Does Push Air
Installed on porch with 10 1/2 foot ceiling with short extension supplied. Porch is enclosed (solid wall) on three sides. Fan does not push any air. Other than that it runs fine.
Current Answers
Related Hunter 22710 Manual Pages
Installation Guide - Page 1
... efficiency, and energy savings. For instructions to install your ceiling fan, go to your fan manual and continue with 2 • Installing the Ceiling Plate. Tools and Supplies You May Need
• Drill • ...into ceiling.
Preparing the Fan Site
8' Minimum Ceiling Height
7' Minimum to Floor
30" From Wall or Nearest Obstruction
Step 1 Choose the Fan Site
Proper ceiling fan location ...
Owner's Manual - Page 1
Catalog No.
Model Name
Model No.
Date Purchased
Where Purchased
Type 8 Models
Owner's Guide and Installation Manual
English
Español
Form# 41968-01 20081002 ©2008 Hunter Fan Co. For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual.
Owner's Manual - Page 2
... with the best ceiling fan available anywhere in the off the circuit breakers to the outlet box and associated wall switch location. If you with wiring, use a qualified electrician. • To reduce the risk of personal injury, do not use only the hardware supplied. • To avoid possible electrical shock, before installing your home or...
Owner's Manual - Page 3
... Choice mounting methods. You can purchase Hunter extension downrods. Understanding Mounting and Installer's Choice®
Hunter's patented 3-position mounting system provides you can install your Hunter fan, use only the hardware supplied.
3 41968-01 • 10/02/08 • Hunter Fan Company Support Brace
Ceiling Outlet Box
For ceilings higher than 8 feet high
CAUTION: To reduce...
Owner's Manual - Page 4
...; Lift 40 pounds. 1 • Getting Ready
To install a ceiling fan, be sure you can direct you to a licensed installer or electrician.
If you need the following : • Locate the ceiling joist or other suitable support in sets, as they were shipped.
4 41968-01 • 10/02/08 • Hunter Fan Company
Gathering the Tools
You will need...
Owner's Manual - Page 5
... ceiling plate.
2-3. 2 • Installing the Ceiling Plate
CAUTION: To avoid possible electrical shock, before installing your fan,...the slotted holes in the ceiling plate into the wood ...ceiling plate are pointing toward the ceiling peak.
5 41968-01 • 10/02/08 • Hunter Fan Company Isolator
Ceiling Plate
Flat Washer
Step 2-2 Steps 2-3 - 2-5
3" Wood Screw
For Angled Ceilings...
Owner's Manual - Page 6
... the wires from a flat or angled ceiling, insert the downrod through the canopy and canopy trim ring. Raise the fan and place the hook on the threads. Align the holes in these installation instructions.
3-1. Skip to install the pipe and ball assembly.
To assemble fan to hang down from the fan. Step 3-7
U-shaped Hole
Steps 3-2 - 3-3
Downrod...
Owner's Manual - Page 7
...
a wire connector over them carefully back through the ceiling plate into the outlet box.
4-7. 4 • Wiring the Fan
All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. Wall switches are unfamiliar with the grounded wires on one side of the outlet box and the ungrounded wires on...
Owner's Manual - Page 8
... tabs on the ceiling plate.
5-3.
Once all three screws are in, tighten them.
5-5. Locate the tab indicators, small bumps on opposite sides of the ring toward... Steps 5-4 - 5-5
Ceiling Plate Canopy Trim
Ring
Step 5-3
Canopy Screw
8 41968-01 • 10/02/08 • Hunter Fan Company 5 • Installing the Canopy and Canopy Trim Ring
5-1. Partially install the three canopy screws ...
Owner's Manual - Page 9
...three blade assembly screws. For each blade to the fan. Your fan may appear slightly loose after screws are installed in the motor to the fan).
6-1. Remove the blade mounting screws and rubber ... 6-2
Use without grommet
Blade Mounting
Screw
Step 6-4
9 41968-01 • 10/02/08 • Hunter Fan Company
If your fan has grommets, insert them by hand into the holes on the blades.
6-2. ...
Owner's Manual - Page 10
... - 7-4
10 41968-01 • 10/02/08 • Hunter Fan Company Note: If you are polarized and will only fit together one way. Thread the finial with steps 7-3 - 7-4 to 8 • Installing the Light ...plug connector from the sack parts) through the side holes of the mounting plate and tighten them . Note: Both plug connectors are not installing the light fixture, proceed with rod (from ...
Owner's Manual - Page 11
Place each shade on this
ceiling fan contains a device that limit or the marked
limit on a socket. 8-3. Exceeding that ... finial until it is tight. 8-2.
Finial
Step 8-1
11 41968-01 • 10/02/08 • Hunter Fan Company
Steps 8-2 - 8-3 Plug in fire hazard or improper
operation. 8 • Installing the Light Fixture
8-1. Install 4 candelabra bulbs (40 Watt maximum).
Owner's Manual - Page 12
... chain uses a breakaway connector that separates if the chain is jerked. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in the same manner as they will distribute the warmer air trapped at the ceiling around the room without causing a draft.
9-5. Restart fan. The pull chain has four settings in sequence: High, Medium, Low...
Owner's Manual - Page 13
... canopy, check all connections according to make sure the wattage and type of light bulbs installed match the specifications on . 6. Remove the shipping bumpers. Tighten all the blades.
10 • Troubleshooting
Problem: Nothing happens; Check to ensure it is cracked. Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee 38114
13 41968-01 •...
Parts Guide - Page 1
Before installing your fan, record the following information for your Local Service Center. 3. Fan Parts (Not Drawn to Scale)
150 Globe / Shade
75 ...Set
7 Hanger Ball / Downrod
Assembly
4 Canopy Trim Ring
2 Ceiling Plate
29 Switch Housing Cover
Missing / Broken Parts: Call 1-888-830-1326
267 Finial, Switch Housing
Fan does not work: 1. For additional information on: Hunter Products Trouble...
Parts Guide - Page 2
...64 65 68 71 100 28 29 44 46 47 49
66 67 70 150 267 75
Item Name * Hanging System Kit
Ceiling Plate Canopy Canopy Trim Ring Hanger Ball / Downrod Assembly Set Screw (Not shown) Low Profile Washer Canopy Screw Wood Screw ...000 95521-00-860 05989-01-000 63730-07-247 05172-01-000 86234-04-000 74940-10-306 07570-01-000
22710 95533-02 New Bronze
Part # 94945-30-000 95522-30-000 85637-01-299 95518-05-...
Similar Questions
Need For Replacement Switch Housing Assembly In Hunter Ceiling Fan.
Fan model 20728, housing part Purchased 12/2009
Fan model 20728, housing part Purchased 12/2009
(Posted by Anonymous-161179 7 years ago)
How Do I Install My Fan Without The Light Kit?
how do I install my fan without the light kit
how do I install my fan without the light kit
(Posted by Mgdel634 7 years ago)
Can I Install This Fan Without The Light Kit?
Can I purchase a cap to cover the light kit mount so this fan can be installed without the light kit...
Can I purchase a cap to cover the light kit mount so this fan can be installed without the light kit...
(Posted by evadwest 10 years ago)
Please I Need To Know How To Use The Settings For Electric Heat. Fan On Or Auto
(Posted by Dawndisalvo 11 years ago)
On The Hunter 22710 Fan Can You Get A Different Light Kit For This Fan.
I want to know if you can get a different light kit since it plugs in like a wall plug. Other light ...
I want to know if you can get a different light kit since it plugs in like a wall plug. Other light ...
(Posted by jpuckett6257 12 years ago)