Hunter 21325 Support Question

Find answers below for this question about Hunter 21325.
Need a Hunter 21325 manual? We have 4 online manuals for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by rjaynes on April 26th, 2012

Is It Possible To Replace The Light Kit On This Fan?

The lights that come with this fan cast the light upward into the fan blades. If you have the light on with the fan running, it creates a strobe effect which is quite irritating. I would like to replace it with a kit where the globes are downward facing.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Hunter 21325 Manual Pages

Installation Guide - Page 1

...clearance hole is acceptable and safe for your fan manual and begin with the rotating fan blades during normal operation. • e fan blades are at least 7 feet above the ceiling ...fan supply line through the inner holes of the fan and light kit. Step 5 Step 5 Prepare the Wiring 5-1. Choose a fan site where: • No object can come in the off every item, prepare a new fan...

Owner's Manual - Page 1

Date Purchased Where Purchased Type 2 Models Owner's Guide and Installation Manual English Español Form# 45037-01 20110606 ©2011 Hunter Fan Co. For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name Model No.

Owner's Manual - Page 2

...blade attachment system when installing, balancing, or cleaning the fan. If you complete instructions for installing and operating your fan. We are unfamiliar with national and local electrical codes and ANSI/NFPA 70. SAVE THESE INSTRUCTIONS. • Use only Hunter replacement...supplied. • To avoid possible electrical shock, before installing your fan, disconnect the power by turning...

Owner's Manual - Page 3

... high. • The fan blades have no obstructions to airflow, such as specified by an approved connector. • Six inches of the fan blade tips. • The fan is secured to Section 2 • Installing the Ceiling Plate. Ceiling Hole • The outlet box clearance hole is recessed a minimum of the fan and light kit. Preparing the Fan Site Step 1 -

Owner's Manual - Page 4

... brace between two joists. Drill pilot holes no larger than the minor diameter of the wood screws (5/64") through the drywall or plaster of the fan and light kit. Attach the outlet box directly to the outlet box with two #8 x 1-1/2" Step 4 wood screws and washers. You have now successfully prepared your...

Owner's Manual - Page 5

...than 8 feet high CAUTION: To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to assure stability and wobble-free...'s Choice® Hunter's patented 3-position mounting system provides you can install your Hunter fan in this manual include instructions for ceilings less than 8 feet, you maximum installation flexibility...

Owner's Manual - Page 6

... support in ceiling. • Drill holes for any parts are installing more than one fan, keep the fan blades and blade irons (if applicable) in the pullout sheet called "Preparing the Fan Site." Preparing the Fan Site Before you begin installing the fan, follow all the instructions in sets, as they were shipped. 6 45037-01 • 06...

Owner's Manual - Page 7

... LEFT Step 2-3 (Angled Ceiling Only) 7 45037-01 • 06/06/11 • Hunter Fan Company RIGHT Tighten the screws into the pilot holes you drilled in the hanger bracket with four pre-installed... slotted holes in Illustration 2-3 (left or right view). Note: Your fan comes with the pilot holes you drilled. 2 • Installing the Hanger Bracket 2-1. For proper alignment use...

Owner's Manual - Page 8

... the next page. Once assembled, do not remove the downrod. Steps 3-4 - 3-5 WARNING: Fan may fall if not assembled as shown in these installation instructions. Feed the wires from unscrewing. ... will still be visible; Downrod Canopy (with the indent in the hanger bracket. (Rotate the fan until you hear the notch pop into the hanger bracket. 3-5. For low profile mounting (ceilings less...

Owner's Manual - Page 9

... mounting (ceilings less than 8 feet high), see steps 3-6 - 3-10 on the previous page. Place the low profile washer from the hanger ball bracket. 3-7. Raise the fan and place the hook on top of the canopy. Step 3-6 (Not Actual Size) Steps 3-8 - 3-9 Low Profile Washer Step 3-7 (Detail) Low Profile Washer Adapter Canopy Trim...

Owner's Manual - Page 10

...from the ceiling to the black (ungrounded) and the black/white wire (ungrounded) from the fan CAUTION: Be sure no bare wire or wire strands are not included. Select an acceptable general... wire (grounded) from the ceiling plate and the green ground wire from the fan. 4-5. Turn the wire connectors upward and push them , then twist clockwise until tight. Before attempting installation, make ...

Owner's Manual - Page 11

... 2 full turns) in the hanger bracket. 5-2. Hanger Bracket Canopy Trim Ring Step 5-4 Step 5-3 Step 5-5 Canopy Screw 11 45037-01 • 06/06/11 • Hunter Fan Company 5 • Installing the Canopy and Canopy Trim Ring 5-1. Twist canopy trim ring counter clockwise until it releases from canopy. Raise the canopy over the...

Owner's Manual - Page 12

...) Step 6-4 12 45037-01 • 06/06/11 • Hunter Fan Company Attach each blade, insert one blade mounting screw through the blade iron, and attach lightly to secure the metal shipping ring. 6-4. 6 • Assembling the Blades Hunter fans use several styles of the motor. Your fan may appear slightly loose after screws are installed in the motor...

Owner's Manual - Page 13

... firmly. Steps 7-1 - 7-4 Housing Assembly Screw Upper Switch Housing Plug Connector Lower Switch Housing Housing Assembly Screw 13 45037-01 • 06/06/11 • Hunter Fan Company Align the keyhole slots in the narrow end of the housing. 7-3. Turn the housing counterclockwise until the housing assembly screws are firmly situated in...

Owner's Manual - Page 14

... sockets. 7-10.Install three 14W CFL light bulbs Plug Connector Steps 7-5 - 7-6 Lower Switch Housing Housing Assembly Screw Plug Connector Detail Shade 14 45037-01 • 06/06/11 • Hunter Fan Company To attach the lower switch housing, connect the upper plug connector from the motor to the lower plug connector in...

Owner's Manual - Page 15

...fan pull chain controls power to clean the blades. In winter, having the fan draw air upward (clockwise blade rotation) will opposite position. For cleaning finishes, use an artistic agent, but never abrasive cleaning agents To Change Airflow Direction Turn the fan off and let it come...the light. 8 • Operating and Cleaning Your Ceiling Fan 8-1. Restart fan. Turn on the blades. ...

Owner's Manual - Page 16

... the switch housing. 4. Check to ensure it is properly seated. Tighten all the blades. If so, replace all blade iron screws. 3. If your fan wobbles when operating, use the enclosed balancing kit and instructions to the wiring the fan section. 3. Turn power off, support fan very carefully, and check that the switch is cracked. Turn power on...

Parts Guide - Page 1

... 63756-11 3 66763-01 3 75642-02 3 88715-01 Hunter Fan Company • 2500 Frisco Avenue • Memphis, TN 38114 &#...Blade Iron Set Blade Set Screw, Blade Iron Armature Hardware Kit Blade Grommet Blade Assembly Screw Screw, Machine, 6-32 Wire Connector Screw, Switch Housing Assembly Balancing Kit Pull Chain Pendant Pull Chain Light bulb / Bulb Globe Assembly Nut Globe/Shade Model # 21325...