Honeywell T8034 Support Question
Honeywell T8034 Support Question
Find answers below for this question about Honeywell T8034.Need a Honeywell T8034 manual? We have 1 online manual for this item!
Question posted by rcwatts23 on December 1st, 2011
How To Get T8034c1341 Apart From Base To See Wiring
how do i get the thermostat apart from base to see wiring
Current Answers
Answer #1: Posted by quaff on December 1st, 2011 4:18 PM
quaff
Member since:
November 13th, 2011 Points: 537,590
Member since:
November 13th, 2011 Points: 537,590
Along the bottom of the thermostat, where it meets the wall mounting plate, there are a couple of slots. Use a coin or flathead screw driver in these slots to separate the thermostat from the plate. Once the bottom is separated, simply pull the rest of the unit off by hand. The mounting plate is held in place by a couple of screws.
Related Honeywell T8034 Manual Pages
Owner's Manual - Page 1
... 6
Manual de Uso
Español: Página 11
T834 Series
Thermostat
This manual covers the following models: Horizontal Mount: T8034N • Vertical Mount: T834N/T834L
Pre...-installation checklist
Check package contents:
• Thermostat • Wall anchors & screws (2 each)
Before you begin, make sure you have:
•...
Owner's Manual - Page 2
T834 Series
Product application
This thermostat provides control of 24 Vac single-stage heating and cooling systems.
System Types
• Gas, oil, or electric heat with air conditioning
• Warm air, ...
Owner's Manual - Page 3
...**
G Fan relay. Remove metal jumper if two-transformer system. Shielded cable is not required.
3
Wire specifications Use 18-gauge thermostat wire. English: Page 1 • Français: Page 6 • Español: Página 11
Base installation
1 Pull wires through base, position over anchors, then insert and tighten mounting screws. Terminal Designations
R Heating power. Check level...
Owner's Manual - Page 4
... heat systems. (This setting is for systems that allow the thermostat to control the fan in a call for heat, if a fan wire is connected to the G terminal.)
Set heat anticipator (except model...) Warm air (standard) Electric heat
Setting 1.2 0.8 0.8 0.4 0.3
Thermostat mounting
Align the slots on the cover with tabs on the sides of the base, then push gently until the cover snaps into place.
Similar Questions
Common Wire On Honeywell T834 Thermostat
I'm trying to connect this new thermostat (Honeywell T834) on my AC unit (cooling only) but I dont h...
I'm trying to connect this new thermostat (Honeywell T834) on my AC unit (cooling only) but I dont h...
(Posted by melbltz 2 years ago)
Access To Rct8100 Thermostat Wiring
Do I need to unscrew face panel on Honeywell Rct8100 thermostat to get to wiring or will it opo off ...
Do I need to unscrew face panel on Honeywell Rct8100 thermostat to get to wiring or will it opo off ...
(Posted by poetman 11 years ago)
Magic Stat Thermostat Wiring
I had reason to remove my model CT2400 thermostat from the wall and I noticed that the green wire wa...
I had reason to remove my model CT2400 thermostat from the wall and I noticed that the green wire wa...
(Posted by dkingusgs 12 years ago)
Wired Thermostat Outside Unit Slows Down But Will Not Stop When Set Temp Reached
Wired according to instructions... appears to work but outside unit will not shut off when temp set ...
Wired according to instructions... appears to work but outside unit will not shut off when temp set ...
(Posted by decheverri 12 years ago)
How To Connect The 2 Wires From My Existing Thermostat?
I just bought a Honeywell RTH6400 series thermostat but I have problems to connect it. My old 24v th...
I just bought a Honeywell RTH6400 series thermostat but I have problems to connect it. My old 24v th...
(Posted by huguessimard300 13 years ago)