Honeywell RTH2310B Support Question
Honeywell RTH2310B Support Question
Find answers below for this question about Honeywell RTH2310B.Need a Honeywell RTH2310B manual? We have 1 online manual for this item!
Question posted by chavsha on October 30th, 2013
Honeywell Thermostat Rth2310b How To Reset Filter Display
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310B Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-04
Owner's Manual - Page 2
... instructions in the following pages.
1) Identify your system type. 2) Remove your old thermostat. 3) Identify the wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the thermostat. 10) Set the system. We are here to help. Call 1-800-468-1502...
Owner's Manual - Page 3
...
If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502. This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi...
Owner's Manual - Page 4
...: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Do not remove wallplate yet. Quick Installation Guide
2 Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Owner's Manual - Page 5
... label each of these wires with electrical tape, so it cannot touch and short other wires.
If any wires are not attached to your new thermostat. Do not use non-connected wires.
Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they...
Owner's Manual - Page 6
Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
4 Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes).
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6
Labels don't match? If a wire does not match any excess wire back into the wall opening.
Owner's Manual - Page 9
Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace.
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 RTH2310 Programmable Thermostat
7 Specify Furnace Type
6.
HE Place the jumper to the G terminal.
Owner's Manual - Page 10
... ambient temperature once it is installed on the wall. Afterwards, the screen displays the actual temperature. By default, the setpoint is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. Quick Installation Guide
8 Install Batteries
7.
1) Pull out the...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
9 Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
... (gas or oil), 5=12 min (alternate setting for gas or oil), 6=10 min (electric).
5 The corresponding cooling cycle lengths are shown in U.S.A.
DISPLAY
DESCRIPTION
OPTIONS 1
Temperature display
°C or °F
Time display
12 h or 24 h
Early Start 2
On or Off
Heating cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-04
Similar Questions
Filter Displayed On Front Of Thermostat
What does it mean when the filter symbol come on? Do I need to change the filter. If so, how do I ha...
What does it mean when the filter symbol come on? Do I need to change the filter. If so, how do I ha...
(Posted by layondawilliams 10 years ago)
Honeywell Thermostat Rth2310b What Is The Filter
(Posted by ak414karat 10 years ago)