Home » Honeywell » Thermostats » Honeywell RTH2310B

Honeywell RTH2310B Support Question

Find answers below for this question about Honeywell RTH2310B.
Need a Honeywell RTH2310B manual? We have 1 online manual for this item!

Honeywell Overview Questions Manuals Reviews Videos Research

Question posted by layondawilliams on December 24th, 2013

Filter Displayed On Front Of Thermostat

What does it mean when the filter symbol come on? Do I need to change the filter. If so, how do I have to change it? Will my heater stop working?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by moosewithabow on August 24th, 2014 8:29 PM

moosewithabow

Member since:
August 24th, 2014

Points: 0

100
points

it's a reminder to change the filter, it's been 500 hours of running time since the clear button was held down for 3 seconds. it doesn't know if the filter needs to be changed, but you should check it. replace it if needed, then hold the clr button down for 3-4 seconds and the filter message will go away. When the unit has run for another 500 hours, the filter message will come back.

Related Honeywell RTH2310B Manual Pages

Owner's Manual - Page 1

Quick Installation Guide RTH2310 Programmable Thermostat 69-2214EF-04

Owner's Manual - Page 2

.... 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the thermostat. 10) Set the system. Do you need assistance? Quick Installation Guide Installation is Easy Your new thermostat has been designed for fast and easy installation. Call 1-800-468-1502. 1 We are here to help.

Owner's Manual - Page 3

... If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502. This thermostat is compatible with the following systems: • Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi...

Owner's Manual - Page 4

... the trash if it contains mercury in a sealed tube. Quick Installation Guide 2 Remove Old Thermostat 2. 1) Turn power off at the heating/cooling system. 2) Remove old thermostat, but leave wallplate with wires attached. Do not remove wallplate yet. MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling ...

Owner's Manual - Page 5

... wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be connected to your new thermostat. RTH2310 Programmable Thermostat 3 Identify Wires 3. If any wires are not attached to your old thermostat or are labeled. Wrap the wires around a pencil to identify wires.

Owner's Manual - Page 6

Insert plastic anchors. Quick Installation Guide 4 Mount New Wallplate 4. 1) Remove coverplate. 2) Loosen screw (the screw remains captive on wallplate). 3) Remove thermostat. 4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws. 5

Owner's Manual - Page 7

... with the terminal having the same letter. 2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws. 3) Push any terminal on the thermostat, see next page. 6 If a wire does not match any excess wire back into the wall opening.

Owner's Manual - Page 9

J2 jumper HG Leave the jumper in this position if you have an electric furnace. 8 HE Place the jumper to the G terminal. Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. RTH2310 Programmable Thermostat 7 Specify Furnace Type 6.

Owner's Manual - Page 10

... 5 seconds. By default, the setpoint is installed on the wall. After the batteries are holding the thermostat. Quick Installation Guide 8 Install Batteries 7. 1) Pull out the battery cover. 2) Install the batteries as shown. Observe the polarity. 3) Reinstall the battery cover. You will display the ambient temperature once it is 70 °F (21 °C). 9

Owner's Manual - Page 11

RTH2310 Programmable Thermostat 9 Install thermostat 8. 1) Mount the thermostat on the wallplate. 2) Tighten the screw and install the coverplate. 3) Turn power back on at the heating/cooling system. 10

Owner's Manual - Page 12

DISPLAY DESCRIPTION OPTIONS 1 Temperature display °C or °F Time display 12 h or 24 h Early Start 2 On or Off Heating cycles per hour 3 2, 3, 4, 5 or 6 4 Cooling cycles per hour 3 2, 3, 4, 5 or 6 5 1 Default ...enter or exit the setup menu. 2) To advance to the next function, briefly press both and buttons simultaneously. 3) To change the setting, press the or button.

Owner's Manual - Page 13