Honeywell RTH2310B Support Question
Honeywell RTH2310B Support Question
Find answers below for this question about Honeywell RTH2310B.Need a Honeywell RTH2310B manual? We have 1 online manual for this item!
Question posted by jonorMister on September 1st, 2013
How To Set A Honeywell Thermostat Rth2310b
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310B Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-04
Owner's Manual - Page 2
... instructions in the following pages.
1) Identify your system type. 2) Remove your old thermostat. 3) Identify the wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the thermostat. 10) Set the system. Call 1-800-468-1502.
1 Do you need assistance? Quick Installation...
Owner's Manual - Page 3
...
If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502.
This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi...
Owner's Manual - Page 4
... NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3
Quick Installation Guide
2 Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Contact your old thermostat in the trash if it contains mercury in a sealed tube.
Owner's Manual - Page 5
...they will not be connected to identify wires.
If any wires are not attached to your new thermostat. Wrap the bare metal end of each wire. Do not use C or C1 wires
Identify and....
IGNORE WIRE COLORS: Use terminal screw designations to your old thermostat or are labeled. RTH2310 Programmable Thermostat
3 Identify Wires
3.
Wrap the wires around a pencil to prevent them from falling ...
Owner's Manual - Page 6
Quick Installation Guide
4 Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors.
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6
RTH2310 Programmable Thermostat
5 Connect Wires (typical wiring) 5. If a wire does not match any excess wire back into the wall opening. Labels don't match?
Owner's Manual - Page 9
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8
HE Place the jumper to the G terminal.
RTH2310 Programmable Thermostat
7 Specify Furnace Type
6. Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace.
Owner's Manual - Page 10
... performs a series of tests for approximately 5 seconds. Afterwards, the screen displays the actual temperature. After the batteries are holding the thermostat. It is 70 °F (21 °C).
9 The thermostat will hear a clicking
sound. Observe the
polarity. 3) Reinstall the battery cover. Quick Installation Guide
8 Install Batteries
7.
1) Pull out the battery cover. 2) Install...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
9 Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
... Use the system switch to switch between the two parameters.
4 For optimal heating control, use the setting that matches your system as follows: 2=30 min, 3=20 min, 4=15 min, 5=12 min,...hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are as follows: 2=30 min (steam, gravity), 3=20 min (hot water, 90%+ high-efficiency furnace), 4=15 min (gas or oil...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-04
Similar Questions
Video Of How To Set A Honeywell Thermostat Rth2310b
(Posted by karaSnie 10 years ago)
Need Instructions On How To Set Thermostat Honeywell Chronotherm Iii Ct8602c4443
(Posted by albaraul 12 years ago)