Honeywell RTH2310B Support Question
Honeywell RTH2310B Support Question
Find answers below for this question about Honeywell RTH2310B.Need a Honeywell RTH2310B manual? We have 1 online manual for this item!
Question posted by karaSnie on October 31st, 2013
Video Of How To Set A Honeywell Thermostat Rth2310b
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell RTH2310B Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-04
Owner's Manual - Page 2
...-1502.
1 We are here to help.
Just follow the simple step-by-step instructions in the following pages.
1) Identify your system type. 2) Remove your old thermostat. 3) Identify the wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the...
Owner's Manual - Page 3
... the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type...
Owner's Manual - Page 4
... in a sealed tube.
MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3 Quick Installation Guide
2 Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Do not remove wallplate yet.
Owner's Manual - Page 5
.... IGNORE WIRE COLORS: Use terminal screw designations to prevent them from falling though the wall opening.
4 If any wires are not attached to your old thermostat or are labeled. Do not use non-connected wires.
Disconnect wires and remove the old wallplate only after all wires are attached to a terminal marked...
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
4 Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors.
Owner's Manual - Page 7
Labels don't match? RTH2310 Programmable Thermostat
5 Connect Wires (typical wiring) 5.
If a wire does not match any excess wire back into the wall opening.
Remove jumper if you have both R and Rc ... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6
Owner's Manual - Page 9
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8
HE Place the jumper to the G terminal. RTH2310 Programmable Thermostat
7 Specify Furnace Type
6. Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace.
Owner's Manual - Page 10
... 5 seconds. Afterwards, the screen displays the actual temperature. Observe the
polarity. 3) Reinstall the battery cover. By default, the setpoint is installed on the wall. The thermostat will hear a clicking
sound. Quick Installation Guide
8 Install Batteries
7.
1) Pull out the battery cover. 2) Install the batteries as shown. You will display the ambient temperature...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
9 Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
... cycles per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are as follows: 2=30 min, 3=20 min, 4=15 min, 5=12 min, 6=10 min
69-2214EF-04 M.S.
Quick Installation Guide... water, 90%+ high-efficiency furnace), 4=15 min (gas or oil), 5=12 min (alternate setting for gas or oil), 6=10 min (electric).
5 The corresponding cooling cycle lengths are shown in...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-04
Similar Questions
Need Instructions On How To Set Thermostat Honeywell Chronotherm Iii Ct8602c4443
(Posted by albaraul 12 years ago)