Hitachi VB16Y Support Question
Hitachi VB16Y Support Question
Find answers below for this question about Hitachi VB16Y - Rebar Cutter And Bender.Need a Hitachi VB16Y manual? We have 1 online manual for this item!
Question posted by mlemesany on January 16th, 2022
Was Cutting And It Quit With Rebar Stuck In Jaw.
The person who posted this question about this Hitachi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by SonuKumar on January 17th, 2022 7:34 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
https://www.youtube.com/watch?v=MIjWCotQUkc
https://www.youtube.com/watch?v=MIjWCotQUkc&t=65
https://www.youtube.com/watch?v=MIjWCotQUkc&t=78
https://www.youtube.com/watch?v=MIjWCotQUkc&t=93
https://www.manualslib.com/products/Hitachi-Koki-Vb16y-Rebar-Cutter-And-Bender-2770277.html
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Hitachi VB16Y Manual Pages
Instruction Manual - Page 3
... injury, or could result in serious personal injury. Hazards that result from power tool operation and maintenance are caused by the failure to prevent bodily injury or machine damage... could cause machine damage. English
IMPORTANT INFORMATION
Read and understand all of this power tool. An accident can often be avoided by recognizing a potentially hazardous situation before operating or...
Instruction Manual - Page 4
... which it is operated at the rate for additional safety and wear a dust mask if the cutting/bending operation produces dust. 10. Never force a tool or an attachment to rain. It is safer than using this electric tool, take all necessary precautions to contain long hair. 9. Always keep the work area. Always remove...
Instruction Manual - Page 5
... binding and other ). ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE BEFORE USING THE TOOL. NEVER STAND ON THE TOOL. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. Always turn the power off when the tool is not in conjunction with the cutter.
17. When servicing this equipment has a polarized plug (one way. POLARIZED PLUGS To...
Instruction Manual - Page 6
... that air can freely flow at voltages specified on its own cord. Never use a power tool for applications other body parts near the tool's moving parts. Cracks in place. Prevent potential injuries to the instructions provided herein. Cutters, cutting implements and accessories which is cracked. Wear ear plugs when using it may burn out...
Instruction Manual - Page 7
English 14. Solvents such as this tool V volts Hz .......... hertz A amperes no load speed W watt
........... Do not wipe plastic parts with soapy water and dry thoroughly. 15. Wipe plastic parts with a soft ...
Instruction Manual - Page 8
... in or near water or in any environment where electric shock is in good condition. When using an extension cord, be sure to use this tool with a damaged or
frayed electrical cord or extension cord. If in Feet (Meter)
0 - 25 (0 - 7.6)
26 - 50 (7.9 - 15.2)
51 - 100
101 - 150
(15.5 - 30.5) (30.8 - 45...
Instruction Manual - Page 10
... socket bolt
Grip rubber
Fig. 2
Lower cutter
10 English
FUNCTIONAL DESCRIPTION
NOTE: The information contained in this Instruction Manual is designed to assist you in this Instruction Manual may show details or attachments that differ from those on your own power tool. Some illustrations in the safe operation and maintenance of the...
Instruction Manual - Page 11
...-Phase, Series Commutator Motor
Single-Phase, 120 V AC 60 Hz
8 A
(1) Material: Concrete reinforcing bars only (for ASTM) GRADE 40, GRADE 60
(2) Bar Designation Size
#3, #4, #5 (3/8", 1/2", 5/8")
Cutting
Bending
#3 (3/8") ..... 2 pieces #4 (1/2") ..... 1 piece #5 (5/8") ..... 1 piece
#3 (3/8") .... 3 pieces #4 (1/2") .... 2 pieces #5 (5/8") .... 1 piece
0 - 16/min.
39.7 lbs (18.0 kg)
11
Instruction Manual - Page 12
...receptacle is in the ON position, the power tool will the tool get damaged but an accident can result.
2. Power source Ensure that the cutter is securely clamped. If the plug is ...OPERATION
APPLICATIONS
⅜ Cutting of rebar ⅜ Bending of a worn out and deformed cutter with the bolt in a loosely clamped condition can result in damage to the unit and cutter as well as accidents...
Instruction Manual - Page 13
... attempting to turn the motor on again, the motor may not start.
Do not this electric power tools in wet wether conditions. Never bring your hand close to the cutter during operation.
Avoid any work exceeding the maximum capacities. (Rebar diameter: #5 (5/8"))
(Returning Halfway) 1 Select RETURN with the dial. 2 Pull the trigger.
(Selecting the...
Instruction Manual - Page 14
... rubber with new one when replacing the cutter.
● During cutting work, securely hook the rebar to the reaction stopper B during cutting work with the rebar set on corners or ends of the cutter can support a rebar. Never place your hand onto the position where the rebar may fold back.
● The cutter blade can result in the damage...
Instruction Manual - Page 15
.... (Fig. 7) If the switch trigger is released in it on the lower cutter.
(5) When the rebar is set, make sure that the unit is not a hand held tool.
CAUTION: Even after
placing it . English
HOW TO USE (CUTTING)
1. Normal cutting (Fig. 5) (1) Turn the lever in the direction of the unit described in the unit. Fig...
Instruction Manual - Page 16
... as shown in the
following diagram. (Fig. 11)
Blade Fig. 9 Fig. 10
Cutter guard
Upper cutter
Lower cutter
16 When the hexagon socket bolt
that fixes the upper cutter comes out of the rebar can be a fear of rebar.
2. Service life of cutter (Fig. 9)
Repeated cutting of the
cam cover, turn the switch OFF and stop the
motor...
Instruction Manual - Page 17
... of the setting dial depending upon the difference of rebar's thickness. CAUTION:
G Install the cutter and accessories securely according to install them properly, they... remove the cutter. (Pushing the cutter guard up .
(2) Align the hole of a new cutter and the position of the upper cutter.)
Fig. 11
4. Dial indication
45°
90°
135°
180°
Condition of rebar
45°...
Instruction Manual - Page 18
... scatter into pieces and cause injuries.
⅜ The rebar you don't carry out the cutting work. If the cover is kept open, the cutter can sometimes differ if the diameter or hardness of the rebar is a fear of getting your hand onto the position where the rebar may fold back.
⅜ Do not bend any...
Instruction Manual - Page 19
... required bending length is to the VB16Y for base insertion
19
How to install deflection guard The deflection guard is horizontal with the turntable surface. Be absolutely sure to use the unit only after marking sure that it to protect the persons around the rebar cutter/bender in case a rebar splinters into pieces and deflects...
Instruction Manual - Page 20
... bending has been finished.
English
(1) Insert the base of the deflection guard into the
slot of the rebar cutter/bender. (Fig. 18)
(2) Open the guard fully by eye measurement in addition to the dial setting. ... and the fixed length is 20" (inside dimension of the deflection guard). CAUTION: G Set a rebar on the rebar cutter/bender so that the bending length is heard. (Fig. 19)
4.
Instruction Manual - Page 21
This hole comes in quite handy when used to its own flexure. If this occurs, you can return the bending roller to the home position by eye measurement", the rebar can sometimes get caught ...return" position. Using hole to fix unit in the bending roller due to remove the rebar when it . Removing rebar during cutting operation. (Fig. 22)
8. This is provided at a low speed in "bending...
Instruction Manual - Page 22
...43 indicated in motor
trouble. Service and repairs All quality power tools will result in the figure. WARNING: Using this Reber cutter/bender with a new one as soon as excessive abrasion is extremely
...same carbon brush Numbers
0.24" (6 mm)
shown in reduced cutting efficiency and may cause overloading of the power tool. In addition, always keep carbon brushes clean and ensure that ...
Instruction Manual - Page 23
...or accessory can be dangerous and could cause injury or mechanical damage. Otherwise, there is a fear that the rebar may snap.
(1) Cutter (Fig. 25)(Code No. 319706) * One set containing two pieces
(2) Center Roller (D 50) Set...: ø50 mm). English
ACCESSORIES
WARNING: Accessories for this power tool are mentioned in diameter) using the center roller
set (D38) and center roller set (D50).
Similar Questions
Rebar Bender Cutter Won't Cut
While using my hitachi rebar bender to cut #4 rebar the cutters got stuck in the closed position and...
While using my hitachi rebar bender to cut #4 rebar the cutters got stuck in the closed position and...
(Posted by noconnor 1 year ago)
Why Did My Cutter Stop Cutting And Bending. Is There A Reset Button ?
(Posted by jdlconcrete 2 years ago)
Square Clean Cuts
My saw sat unused for about 6 years. Now it is burning and uneven cutting. I know how to adjust fenc...
My saw sat unused for about 6 years. Now it is burning and uneven cutting. I know how to adjust fenc...
(Posted by patf10763 3 years ago)
Cutting Out Of Square
I have a hitachi c10fce2 mitre saw that is not cutting perpendicular to the fence, it is actually cu...
I have a hitachi c10fce2 mitre saw that is not cutting perpendicular to the fence, it is actually cu...
(Posted by tbartelme 12 years ago)