Hitachi M12VC Support Question
Hitachi M12VC Support Question
Find answers below for this question about Hitachi M12VC - 2-1/4 Peak HP Variable Speed Fixed Base Router.Need a Hitachi M12VC manual? We have 2 online manuals for this item!
Question posted by jimandjosehorn on July 29th, 2022
How Long Should It Take To Download The Owner's Manual?
Been downloading for an hour and the progress bar is still not complete.
Current Answers
Answer #1: Posted by SonuKumar on July 29th, 2022 11:11 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,619,310
Member since:
May 9th, 2021 Points: 16,619,310
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Hitachi M12VC Manual Pages
Instruction Manual - Page 3
... procedures.
English
IMPORTANT SAFETY INFORMATION
Read and understand all of this Instruction Manual and in the sections which contain the operation and maintenance instructions. NOTE ... Instruction Manual. Most accidents that must be avoided by recognizing a potentially hazardous situation before operating or maintaining this power tool. Hazards that result from power tool operation ...
Instruction Manual - Page 4
... as pipes, radiators, ranges and refrigerators. Do not wear loose clothing or jewelry. SAVE THESE INSTRUCTIONS
1. Contain long hair. Keep your finger on invites accidents.
4 Do not use common sense when operating a power tool. Water entering a power tool will increase the risk of fumes. (3) Keep bystanders children, and visitors away while operating a power...
Instruction Manual - Page 5
... footing and balance enables better control of this manual. Any tool that may be suitable for one tool, may result in the hands of the tool "live" and shock the operator.
2. Accessories...the power source before making any other condition that is dangerous and must be used with another tool.
5. Keep proper footing and balance at the rate for which it on . Dust mask, ...
Instruction Manual - Page 6
... the router bases. no .......... Your risk from the workpiece before operation. Check the bit carefully for the bit to come to be violently thrown. 17. Keep hands away from the tool towards the rear. 15. Always switch off and wait for cracks or damage before
operation. 6. The motor is not designed to a complete stop...
Instruction Manual - Page 7
... gage. If in good condition.
An undersized cord will draw. When using an extension cord, be sure to use one heavy enough to use this tool with a damaged or
frayed electrical cord or extension cord. SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND...
Instruction Manual - Page 8
... manual. NEVER operate, or attempt any maintenance on the tool unless you in the safe operation and maintenance of the power tool.
NAME OF PARTS
Motor Housing
Dial
Switch
Brush Cap
Handle Lever
7/8 3/4 5/8
1/2 3/8 1/4
Scale Ring Base
Collet Chuck
Sub Base
SPECIFICATIONS
Model Motor Power source Collet chuck capacity Current No-load speed Weight (with cord)
Fig. 1
M12VC...
Instruction Manual - Page 9
... short as practicable. If such a fautly receptacle is in the OFF position. Extension cord When the work site is in the ON position, the power tool will start operating immediately and can cause serious injury.
3. The extension cord should be utilized conforms to make appropriate repairs. Contact a licensed electrician to the...
Instruction Manual - Page 10
...shank bit which is provided as
follows. (a) Open the lever. (Fig. 2) (b) While holding the base, turn the motor
housing counterclockwise. (c) Turn it out approximately 1/16" (approx. 2 mm). (3) ...bit. Motor Housing
Base
Fig. 2
Lever
Loosen Tighten
23mm Wrench
Bit
Collet Chuck
16mm Wrench
Fig. 3
10 CAUTION:
ⅷ Ensure that the collet chuck is
disengaged from under the router). (Fig. ...
Instruction Manual - Page 11
... housing (1) Open the lever. (2) While holding the base, insert the motor
housing into the base. (4) Close the lock lever. HOW TO USE THE ROUTER
WARNING: Be sure to switch power OFF and disconnect ...loosens the lever. Adjusting depth of cut (1) Place the tool on a flat wood surface. Rotate the motor housing clockwise into the base aligning the pin with the groove in small increments. To...
Instruction Manual - Page 12
... 7 Screw
Template Guide Adapter
Fig. 8
Centering Gauge
Template Guide Adapter
Screw
Collet Chuck Lever
Fig. 9
4. Guiding the router (1) Template guide (M12VC, M12SC: Optional
accessory) Use the template guide when employing a template for maximum speed. 3.
When making a template, pay particular attention to install insert template guide in center hole in template guide adapter...
Instruction Manual - Page 13
...router along the materials side. 1 Insert the guide bar into the hole in the bar holder, then lightly tighten the 2 wing bolts (A) on the surface of the materials. 5. The reverse is being turned on. (Fig. 15)
(2) Then turn the tool on and wait until the bit attains full speed...the router while keeping the guide plane on top of the bar holder. 2 Insert the guide bar into the hole in the base, ...
Instruction Manual - Page 14
...
NOTE: ⅷ Moving the tool forward fast may burn and mar the cut . Router feed Router feed
workpiece Rotation of the workpiece.
14 It may cause the rotation speed to fluctuate. ⅷ When ... to normal. ⅷ Do not use a power generator as the power source. The rotation speed should return to check dimensions. ⅷ Abnormalities and overloads will depend on the right side in...
Instruction Manual - Page 15
... during maintenance and inspection.
1. Wear limit
43
No.
WARNING: Using this router with a slotted screwdriver. Replacing carbon brushes
Remove the brush caps with a carbon...Brush Cap
Slotted-head Screwdriver Fig. 18
CAUTION: Repair, modification and inspection of power tools, the safety regulations and standards prescribed in Fig. 17. 3. Inspecting the carbon brushes ...
Instruction Manual - Page 16
... standards prescribed in each country must be observed. MODIFICATIONS: Hitachi Power Tools are constantly being improved and modified to the Hitachi Authorized Service Center ... 6. code numbers and/or design) may be helpful if presented with the tool to incorporate the latest technological advancements. B: Code No. Accordingly, some parts (i.e. In the operation and maintenance ...
Instruction Manual - Page 17
...HITACHI. Model M12VC, M12SC (1) 1/4" Collet Chuck (Code No. 323-293) (2) Template Guide Adapter (attaches
to
the router) (Code No...Base (Code No. 323-297) (7) Template Guide (Fig. 19) (8) Lock Nut (Code No. 323-305) (9) Chip Cover (Code No. 323-292) (10) Case (Code No. 323-358)
C
A B
Code No. English
ACCESSORIES
WARNING: ALWAYS use a particular replacement part or accessory with this tool...
Instruction Manual - Page 18
English
OPTIONAL ACCESSORIES sold separately
(1) Straight Guide Set (Code No. 323-342) 1Bar Holder (Code No. 323-343) 2Feed Screw (Code No. 956-793) 3Wing Bolt (Code No. 301-806) 4Guide Bar (Code No. 323-345) 5Straight Guide (Code No. 323-344) 2 3 1 4 5
(2) Dust Collector Set (Code No. 323-346)
NOTE: Specifications are subject to change without any obligation on the part of the HITACHI.
18
Similar Questions
Hitachi Framing Nailer Nr83a
My framing nailer fires two nails at a time . What can I do to solve the problem?
My framing nailer fires two nails at a time . What can I do to solve the problem?
(Posted by rahundl 5 years ago)
How To Adjust Cut Depth Hitachi 10 Compound Miter Saw Manual
(Posted by dbrag 10 years ago)
I Dont Have A Owners Manual
my gun wont shoot nails should adjust it some how
my gun wont shoot nails should adjust it some how
(Posted by moneyharm44 11 years ago)
Operating Manual.
Can anyone please suply an operation manual for the Hitachi CC14SF cut-off machine, thanks.
Can anyone please suply an operation manual for the Hitachi CC14SF cut-off machine, thanks.
(Posted by peterfranklin 11 years ago)
Where Can I Get A Free Manual On The Hitachi C12rsh 12' Slide Compound Miter Saw
(Posted by kathy86883 14 years ago)