Hitachi NR83A2 - 3.25" Full Head Framing Strip Nailer Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi NR83A2 manuals!
Problems with Hitachi NR83A2?
Ask a Question
Free Hitachi NR83A2 manuals!
Problems with Hitachi NR83A2?
Ask a Question
Most Recent Hitachi NR83A2 Questions
My Hitachi Split Ac 6years Old Red Light 7 Times Blinking Kindly Help Any One
(Posted by rameshchithirai651 4 years ago)
Blinking Of Red Led
My ac was not working and started blinking led. For 7 times
My ac was not working and started blinking led. For 7 times
(Posted by ashrafkhan94069 4 years ago)
Hitachi Framing Nailer Nr83a
My framing nailer fires two nails at a time . What can I do to solve the problem?
My framing nailer fires two nails at a time . What can I do to solve the problem?
(Posted by rahundl 5 years ago)
Trigger Problems Nr83a2 S
trigger blows out when air is applied
trigger blows out when air is applied
(Posted by bbertrand70663 7 years ago)
Ribbon Spring
How do I installed a ribbon spring in a Hitachinr83a2 nail gun
How do I installed a ribbon spring in a Hitachinr83a2 nail gun
(Posted by norcaladams77 8 years ago)
Hitachi NR83A2 Videos
Hitachi NR83A2 Round Head 2 inch to 3 1
Duration: :48
Total Views: 2
Duration: :48
Total Views: 2
NR83A2 1Cylinder Removal Video
Duration: :50
Total Views: 165
Duration: :50
Total Views: 165
How to fix a Hitachi NR83A2 framing nailer.
Duration: 7:16
Total Views: 20,477
Duration: 7:16
Total Views: 20,477
Hitachi 21 Degree 3-1/4-in Plastic Collated Full Round Head Framing Nailer - NR83A2
Duration: 2:17
Total Views: 993
Duration: 2:17
Total Views: 993
Popular Hitachi NR83A2 Manual Pages
Instruction Manual - Page 3
... situation before operating or maintaining this Manual. next, pull the trigger to continue driving nails.
- 3 - Follow the same sequence to drive the nail. Hazards that result from the operation and maintenance of the operating instructions, safety precautions and warnings in this nailer. next, press the push lever against the wood to drive the nail. If the trigger is pressed...
Instruction Manual - Page 5
...Never use the Nailer if parts are driven away from the workpiece and hit someone .
19. Rubber gloves and nonskid footwear are combustible or explosive.
11. DO NOT LOAD FASTENERS WITH TRIGGER OR PUSH LEVER DEPRESSED. Before starting work areas of the operation switching device. In order to avoid this undesirable double fire,
⅜ Intermittent operation (Trigger firing) 1) Set the...
Instruction Manual - Page 6
... surface are not further used only when operators and others in work area are used before repair. Operate the Nailer according to malfunction and resulting injuries. Handle the Nailer carefully.
33. USE ONLY PARTS, ACCESSORIES OR FASTENERS SUPPLIED OR RECOMMENDED BY HITACHI.
SAVE THIS MANUAL AND KEEP IT AVAILABLE FOR OTHERS!
- 6 - Only service personnel trained by children...
Instruction Manual - Page 7
... ACTUATION MECHANISM (Switching device: downward position)
Piston Piston O-Ring
Driver Blade
Nose
Adjuster
[ ] Only NR83A2 (with depth adjustment) Push Lever
Valve part
Trigger Switching Device
Valve Bush
Body
Cap Air Plug (Sold separetely)
Ribbon Spring
Stop Lever Nail Feeder
Magazine Assembly
Outlet (Firing Head)
- 7 - Some illustrations in this Manual is designed to assist you in...
Instruction Manual - Page 8
... than those shown below can lead to serious injuries.
The use only the genuine HITACHI nails for M5 screw
1
- 8 - STANDARD ACCESSORIES
1 Eye protection
1
2 Allen wrench for M8 screw
1
3 Allen wrench for M6 screw
1
1
23 4
4 Allen wrench for the NR83A2/NR83A2(S). Plastic-collated strip nails Full-head nails
Min.
.286" (7 mm)
Max.
.3" (7.6 mm)
2" (50 mm) 3-1/4" (83 mm)
.113...
Instruction Manual - Page 10
..., bring it in work properly and parts will wear prematurely. ⅜ Use Hitachi pneumatic tool lubricant.
Trigger
Push Lever
Do not connect air hose
(2) Adjust the air pressure to ANSI Z87.1 specifications. Connect the air hose.
- 10 - Air consumption table
psi Operating pressure (bar)
(kgf/cm2)
80 (5.5) (5.6)
90 (6.2) (6.3)
100 (6.9) (7)
Air consumption
ft3/cycle (ltr/cycle...
Instruction Manual - Page 11
... position
Do not pull Trigger
Depress Push Lever
(4) Separate the push lever from the wood.
Ⅺ The nailer will remain in the diagram. Adjust the air pressure at a higher than required air pressure unnecessarily over stresses the Nailer.
- 11 - Pull the trigger.
Ⅺ THE NAILER MUST OPERATE.
ⅷ Do not exceed 120 psi (8.3 bar 8.5 kgf/cm2).
Using the Nailer at recommended...
Instruction Manual - Page 12
...; Use nail strip at one from above the magazine. Tail Nail Nail Stopper
Magazine
(3) Press the stop lever and slide the nail feeder forward until it contacts the nail strip.
English
LOADING NAILS
WARNING
ⅷ When loading nails into Nailer, 1) do not depress trigger; 2) do not depress push lever;
Stop Lever Nail Feeder
The Nailer is set under the nail stopper of nails overlapped...
Instruction Manual - Page 13
...the upward position (to set the switching device to drive the nail.
This Hitachi nailer includes a nailing operation switching device. nails can be driven each time the push lever is important. Nails can ricochet and hurt someone . ⅷ Never drive nails from both sides of other nails or with finger off the trigger.
3 Depress the push lever firmly until the trigger is released and...
Instruction Manual - Page 14
... air plug on the air compressor tank to
drain any moisture.
- 14 -
This Hitachi nailer may bounce from the recoil of driving a fastener and unwanted subsequent fastener may be driven, possibly causing injury.
ⅷ Some types of loaded nails can spark out of the push lever will not operate properly.)
2 Pull the trigger with the Nailer off the workpiece. 3 Depress the push lever...
Instruction Manual - Page 15
.... ALWAYS WEAR EYE PROTECTION. ADJUSTING THE NAILING DEPTH
[Only NR83A2 (with depth adjustment)]
WARNING
ⅷ Disconnect the air hose from the nailer before turning the adjuster. If nails are driven too deep or shallow into the workpiece, adjust the nailing in half-turn increments.
2
Turn Adjuster
Too Deep
Flush
If nails are driven too deep, turn the adjuster to the shallow side...
Instruction Manual - Page 16
...8540; When not in use . Service parts list
A: Item No. All quality Nailers will be driven at an irregular angle and hurt someone.
2. Inspecting the magazine
1 DISCONNECT AIR HOSE. 2 Clean the magazine. Operator troubleshooting (See page 17)
Nail Feeder Magazine
1 Disconnect air hose
CAUTION
ⅷ Check that differ from a Hitachi authorized service center.
6. A new WARNING LABEL is...
Instruction Manual - Page 17
...blade worn? Driver blade worn?
Use only recommended nails. Contact Hitachi for assistance. Replace ribbon spring. Use only recommended nails. Use larger air hose.
- 17 - Clean magazine and feeder mechanism. Prevent clogging of nail feeder per page 16. HOW Open manual petcock. If problems persist, contact a Hitachi authorized service center for replacement. PROBLEM Nailer operates, but...
Parts List - Page 2
...ORANGE)
1
10 877-307 HEAD CAP AND GASKET SET
1 INCLUD. 8
11
877-368 O-RING (1AP-48)
1
12 877-323 PISTON
1
13 877-316 O-RING (S-90)
3
14 877-312 CYLINDER O-RING ...SPRING
1
47 884-063 PUSHING LEVER (B)
1
48 884-064 ADJUSTER
1
49 880-175 ADJUSTER SPRING
2
50 959-148 STEEL BALL D3.175 (10 PCS.)
2
51 884-062 PUSHING LEVER (A)
1
--- 2 ---
* ALTERNATIVE PARTS
NR 83A2 5 -- 03 PARTS...
Parts List - Page 3
...WASHER M5 (10 PCS.)
1
PLUNGER (B) SPRING
1
PLUNGER (B)
1
NAIL FEEDER
1
RIBBON SPRING
1
NEEDLE ROLLER
1
NYLON NUT M4
1
SPRING WASHER M4 (10 PCS.)
1
NYLON NUT M5
1
SPRING WASHER M5 (10 PCS.)
1
MAGAZINE
1
SLEEVE
1
HEX. BOLT M4X15 (10 PCS.) 1
WASHER
1
STOP LEVER
1
COLLAR
1
STOPPER SPRING
1
REMARKS
NR 83A2
5 -- 03
* ALTERNATIVE PARTS
--- 3 --- SOCKET HD. SOCKET HD...
Hitachi NR83A2 Reviews
We have not received any reviews for Hitachi yet.