Dell PowerConnect 6248 Support Question
Dell PowerConnect 6248 Support Question
Find answers below for this question about Dell PowerConnect 6248.Need a Dell PowerConnect 6248 manual? We have 5 online manuals for this item!
Question posted by Frasen on February 28th, 2014
How To Set Ip On Dell Powerconnect 6248p
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 6248 Manual Pages
User's Guide - Page 19
...-T copper ports and 4 "combo" ports for RJ-45 or SFP interfaces. The Dell PowerConnect 6248 supports 48 1000Base-T copper ports and 4 "combo" ports for RJ-45 or SFP interfaces. The Dell PowerConnect 6248P adds support for a multi-layer switch, including layer 2
switching, IPv4 routing, IPv6 routing, IP multicast, quality of all features, see the software version release notes. Release...
User's Guide - Page 72
... CLI commands.
72
Configuring Dell PowerConnect NOTE: If you 're directly connected to the switch. You can be defined. When finished, exit the session with the quit or exit command.
The switch can access the switch without a user account if you are for use the Easy Setup Wizard.
2. However, to access the switch through Telnet, at...
User's Guide - Page 73
... 2
Boot menu (Special functions)
Reboot
No
Loading program from flash to RAM
Yes Enter Wizard
No
Initial Configuration: IP Address, Subnetmask, Users Basic Security configuration
Wizard Configuration Process
Standard Switch Installation
Advanced Configuration: IP Address from DHCP, IP Address from bootp, Security management
Advanced Switch Installation
Configuring Dell PowerConnect
73
User's Guide - Page 74
... rate using CLI commands:
console#configure
console(config)#line console
console(config-line)#speed 115200
NOTE: Remember to set the baud rate on the terminal emulator software on your workstation to its unique network topology.
General Configuration Information
The PowerConnect 6200 Series switches are delivered with Telnet, SSH, and so forth
74
Configuring Dell PowerConnect
User's Guide - Page 81
... set up, you in this section).
• IP subnet mask for the network
• Default gateway (next hop router) IP address for the autoconfig feature? NOTE: After making any configuration changes, the new configuration must be saved before rebooting.
The Easy Setup Wizard guides you may return later to make the switch manageable. Configuring Dell PowerConnect...
User's Guide - Page 82
... configuration. If there is activated. • Sets up the SNMP community string to be powered on in the field without a serial connection, the switch waits 60 seconds for you to respond to a set-up wizard. The SNMP community string may choose to the highest available access for the Easy Setup Wizard.
82
Configuring Dell PowerConnect
User's Guide - Page 84
...8226; The network management system IP address is 192.168.2.1. &#...[Y/N] y
Step 1:
84
Configuring Dell PowerConnect Would you up as defined above....set up and running an example Dell Easy Setup Wizard session, using the default system configuration. The following session are enclosed in [ ].
Welcome to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch...
User's Guide - Page 85
...to login to the CLI and Web interface. To manage the switch using SNMP (required for SNMP management by default. The wizard automatically assigns the highest ...Configuring Dell PowerConnect
85 For more information on setting up user accounts and changing privilege levels, see the user documentation).
This account is not setup for Dell Network Manager) you must specify the management system IP ...
User's Guide - Page 86
.... Optionally you may request that the system automatically retrieve an IP address from the network via DHCP (this network is reachable 192.168.1.1 This is the configuration information that you for the switch. You will now enter CLI mode. ..... console>
86
Configuring Dell PowerConnect This is incorrect, select (N) to discard configuration and restart the...
User's Guide - Page 88
... Initial HTTP Password • Configuring an Initial HTTPS Password
Modifying Switching Port Default Settings
When configuring/receiving IP addresses through DHCP and BOOTP, the configuration received from these servers includes the IP address, and may include subnet mask and default gateway.
88
Configuring Dell PowerConnect Parameters that only the missing parameters are defined in the CLI...
User's Guide - Page 89
... interface configuration mode for the 10 gigabit Ethernet interface 1. Enter this by the PowerConnect 6200 Series switches:
• SwitchA> -
Table 5-1. this prompt indicates that the CLI is ...Setting 1G Auto-negotiation Enabled On (Enabled) On Off
Configuring Dell PowerConnect
89 SwitchA#configure
SwitchA(config)#exit
SwitchA#
The following table describes the switch port default...
User's Guide - Page 90
... 1 Routing Interfaces: Netdir Multi
90
Configuring Dell PowerConnect NOTE: You do not need to delete the switch configuration to retrieve an IP address for changing the port description on it, in the following commands to retrieve an IP address, the switch acts as shown in order to retrieve the IP address. Enter the following examples. To retrieve...
User's Guide - Page 91
...set to enable access and configuration rights to the switch from the Boot menu. A priority of 15 must be invoked from the local terminal with no password entered. Configuring Dell PowerConnect
91 Interface IP Address
IP... for the local terminal only and allows a one-time access to the switch. If a userdefined password is handled through the AAA (Authentication, Authorization, ...
User's Guide - Page 92
... at the password
prompt. • When changing a switch's mode to enable, enter pass1234.
Configuring an Initial Telnet Password To configure an initial Telnet password, enter the following commands:
console(config)#ip http authentication local console(config)#username admin password user1234 level 15
92
Configuring Dell PowerConnect Configuring an Initial HTTP Password To configure an...
User's Guide - Page 93
Configuring Dell PowerConnect
93...console, a Telnet, or an SSH session.
Enter the following commands:
console(config)#ip https authentication local NOTE: You should generate a new crypto certificate each time you upgrade ...(install a new version of) the control software application on the switch.
Configuring an Initial HTTPS Password To configure an initial HTTPS password, enter the ...
User's Guide - Page 95
...new system image to start? (y/n) y
Configuring Dell PowerConnect
95 When the new image is downloaded, it is an example of the information that appears:
console#copy tftp://10.254.24.64/pc62xxr0v34.stk image
Mode TFTP
Set TFTP Server IP 10.254.24.64
TFTP Path
TFTP Filename ...is saved in the area allocated for the duration of the transfer Are you sure you want to the switch.
User's Guide - Page 112
.... Privilege levels range from 50.1.1.2: icmp_seq=1. console#config
console(config)#username Dell password Dell1234 level 15
console(config)#ip http authentication local
console(config)#ip https authentication local
112
Configuring Dell PowerConnect
Wait 30 seconds for the port to allow privileged level 15 switch access for the Web interface. console>ping 50.1.1.2
64 bytes from 1-15...
Getting Started Guide - Page 14
... as when you received it. • The PowerConnect switch booted successfully. • The console connection was established and the Dell Easy Setup Wizard prompt appears on the screen
of...access to use the local authentication setting only. • Sets up the IP address for the management VLAN. • Sets up the initial configuration of the switch, obtain the following configuration on CLI...
Release Notes - Page 3
... MUST follow the procedure set forth in the Dell PowerConnect 6200 Series Release 3.2 Upgrade Procedure included in your switch becoming inoperable. NOTE: The PC6200 switches when stacked require that this product. It is recommended that the same version of this release note be installed on every switch member.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Introduction
This...
Release Notes - Page 25
... timeout guest-vlan-period
Description
Use this command in Interface Config Mode to set the number of seconds that it is supported. Default: Not applicable
Stacking/... Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide for 90 seconds. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
RADIUS Accounting Servers
Title radius-server host acct
Description The switches ...
Similar Questions
How To Set Ip Address On Powerconnect 2824 Conf
(Posted by krispapaha 9 years ago)
How To Set Up Powerconnect 6248 Via Serial Cable
(Posted by vij77jbk 10 years ago)
Configuring Dell Powerconnect 6248p For Cisco Ip Phone
I have a Dell PowerConnect 6248P and i want to configure it for Cisco IP phone. I need some technica...
I have a Dell PowerConnect 6248P and i want to configure it for Cisco IP phone. I need some technica...
(Posted by taansari 11 years ago)