Cisco NME-X-23ES-1G Support Question
Cisco NME-X-23ES-1G Support Question
Find answers below for this question about Cisco NME-X-23ES-1G - EtherSwitch Service Module Switch.Need a Cisco NME-X-23ES-1G manual? We have 1 online manual for this item!
Question posted by droberts4 on March 30th, 2013
Nme-x-23es-1g Initial Configuration
I am unable to contact the module:
GW12#service-module gi 1/0 session
% telnet connections not permitted from this terminal
I am able to status the module, but unable to establish a connection for configuration
Current Answers
Related Cisco NME-X-23ES-1G Manual Pages
User Guide - Page 5
... a no switchport interface configuration command.
Routed ports support only CEF switching (IP fast switching is connected. it , which you enter the vlan interface configuration command for an access ...you want to permit remote switch administration. For more switches and have those changes automatically communicated to all the other features being configured might generate messages ...
User Guide - Page 6
... VTP domain. The switch ignores advertisements with unique names and internal index associations. VTP servers advertise their VLAN configuration to all trunk connections using either the command...management domain name or an earlier configuration revision number.
and 36-Port Ethernet Switch Module for the entire VTP domain.
When you configure the switch as VTP version) for Cisco...
User Guide - Page 10
.../request frame followed by the client using the dot1x port-control auto interface configuration command, the switch must initiate authentication when it determines that the client has been successfully authenticated. Feature Overview
16- and 36-Port Ethernet Switch Module for authentication information). It then sends an EAP-request/identity frame to the client to request...
User Guide - Page 24
... data link layer) on the same network module. Only switched interfaces can configure source interfaces in the specified VLANs are neighbors of time a receiving device should hold -time information, which it . The show monitor session SPAN session number command displays the operational status of source interfaces.
You can configure EtherChannel as SPAN sources or destinations on...
User Guide - Page 26
...; If you do not configure ACLs, all packets passing through a switch and permit or deny packets from crossing specified interfaces. ACLs can use ACLs to control which the ACL is a sequential collection of permit and deny conditions that the packet has the required permissions to packets. The Ethernet switch network module supports IP ACLs to block...
User Guide - Page 28
...Telnet port. There are permitted will consume bandwidth on the IP subnet to be specified.)
You can be configured on any interface:
Switch (config-ext-nacl)# permit tcp any any Switch (config-ext-nacl)# deny tcp any any Switch (config-ext-nacl)# permit udp any any Switch...Understanding Access Control Parameters Before configuring ACLs on the Ethernet switch network module, you want to perform an...
User Guide - Page 29
..., see the "Understanding Access Control Parameters" section on the Ethernet switch network module. You can be shared by QoS and security. With this feature, you configure this ACL.
• Only four user-defined masks can configure as many ACLs as permit ip 10.1.1.1 any assurance of service (QoS) but you require. All other combinations of 23...
User Guide - Page 64
... 3600 Series, and Cisco 3700 Series
Step 1 Step 2 Step 3
Step 4 Step 5 Step 6
Command configure terminal dot1x re-authentication dot1x timeout re-authperiod seconds
end show dot1x copy running -config startup-config
Purpose Enters global configuration mode.
and 36-Port Ethernet Switch Module for a set period of seconds between reauthentication attempts. To return to change the...
User Guide - Page 65
... Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Configuration Tasks
Note You should change the default value of seconds that the switch ...Command configure terminal dot1x max-req count
Step 3 Step 4 Step 5
end show dot1x copy running -config startup-config
Purpose Enters global configuration mode.
Beginning in the configuration file. Setting the Switch-to...
User Guide - Page 78
... of the conditions is the same as configuring ACLs on the Ethernet switch network module, see Table 11 on page 79). • Bridge-group ACLs. • IP accounting. • ACL support on configuring router ACLs, refer to Cisco IOS IP Command Reference for using them. For a list of permit and deny conditions. An ACL must...
User Guide - Page 162
...Configuration Guide, Release 12.2.
and 36-Port Ethernet Switch Module for ...Switch(config-pmap)# class class1 Switch(config-pmap-c)# police 1000000 131072 exceed-action drop Switch(config-pmap-c)# exit Switch(config-pmap)#
You can be used for the classified traffic. Displays QoS policy maps.
162
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ To return to specify a service...
User Guide - Page 164
... group. and 36-Port Ethernet Switch Module for the policy to specify a service policy. match (class-map configuration) Defines the match criteria to configure the class map named class1. Class1 has one match criteria, which is a numbered ACL:
Switch(config)# access-list 103 permit tcp any any eq 80 Switch(config)# class-map class1 Switch(config-cmap)# match access...
User Guide - Page 165
... the 802.1x process and the switch (Remote Authentication Dial-In User Service [RADIUS] client).
and 36-Port Ethernet Switch Module for the specified interface. To disable...802.1x initialization, configuration, and the interaction with the port manager module.
This command was introduced. Displays 802.1x statistics, administrative status, and operational status for the switch or ...
User Guide - Page 171
...
The following example shows how to create an extended IP ACL and to the "Configuring IP Services" chapter in the named or numbered IP ACL. 16- and 36-Port Ethernet Switch Module for UDP traffic. If operator is always terminated by an implicit deny statement for TCP traffic. Use TCP port names only for all...
User Guide - Page 178
... example shows how to manually reauthenticate the device connected to reauthenticate. You can use the dot1x re...Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
dot1x re-authenticate
To manually initiate a reauthentication of all 802.1x-enabled ports or the specified 802.1x-enabled port, use this command to reauthenticate a client without waiting for the configured...
User Guide - Page 183
...
access-list-number name in interface configuration mode. and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
ip access-group
ip access-group
To control access to the "Configuring IP Services" chapter in the ACL and the list permits the address, the switch forwards the packet. To remove an...
User Guide - Page 185
...the IP ACL for which you enter access-list configuration mode.
In this list.
and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and ...must enter the permit and deny commands to configure the permit and deny access conditions for matching packets to an ACL whose name or number you specify and to the "Configuring IP Services" chapter in global configuration mode. A...
User Guide - Page 196
... of this command. and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
match (class-map configuration)
To define the match criteria to 2699.... specify which fields in the incoming packets are examined to the "Configuring IP Services" chapter in class-map configuration mode.
Examples
The following platforms: Cisco 2600 series, Cisco 3600 series,...
User Guide - Page 205
...
and 36-Port Ethernet Switch Module for it:
Switch(config)# ip access-list extended Internetfilter2 Switch(config-ext-nacl)# permit host 36.10.10.5 any Switch(config-ext-nacl)# permit host 192.1.10.8 any
The following platforms: Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers.
Note For more information about configuring IP ACLs, refer to...
User Guide - Page 217
... to force-unauthorized, but the port has not changed to the "Configuring 802.1x Port-Based Authentication" chapter in the Catalyst 2950 Desktop Switch Software Configuration Guide.
The following is sample output from the Remote Authentication Dial-In User Service (RADIUS) authentication server to auto or force-unauthorized). Table 20 describes the fields in...
Similar Questions
How To Configure Lelnet On Cisco 6504e Switch
after done the configuration of cisco 6405E swiitch, we are not able to telnet the switch, device is...
after done the configuration of cisco 6405E swiitch, we are not able to telnet the switch, device is...
(Posted by sarwaransari 9 years ago)
Cisco Nme-x-23es-1g Initial Configuration
Following instructions in Cisco online docs. I set the ip address for gi 1/0 and attempt to connect ...
Following instructions in Cisco online docs. I set the ip address for gi 1/0 and attempt to connect ...
(Posted by droberts4 11 years ago)
Configure A Cisco Srw2008p Switch For Cisco Ip Phone 7961.
How do I configure a Cisco SRW2008P switch for a Cisco IP Phone 7961. Currently if I plug this phone...
How do I configure a Cisco SRW2008P switch for a Cisco IP Phone 7961. Currently if I plug this phone...
(Posted by victorluster 13 years ago)
Nme-16es-1g, All Port Status Leds Are Green. Even Ones Not Cabled To Anything.
I have come across two NME-16ES-1G switch modules that all port status leds are green.. Even ones no...
I have come across two NME-16ES-1G switch modules that all port status leds are green.. Even ones no...
(Posted by ccasario 13 years ago)
How To Resolve Port Suspended Issue On Nme-16es-1g?
Cisco NME (NME-16-ES-1G) card fatst ethernet port goes down after soem idel tiem. due to this the po...
Cisco NME (NME-16-ES-1G) card fatst ethernet port goes down after soem idel tiem. due to this the po...
(Posted by mmsundara 14 years ago)