Cisco NME-16ES-1G Support Question
Cisco NME-16ES-1G Support Question
Find answers below for this question about Cisco NME-16ES-1G - Etherswitch Service Mod 16.Need a Cisco NME-16ES-1G manual? We have 1 online manual for this item!
Question posted by ccasario on July 13th, 2010
Nme-16es-1g, All Port Status Leds Are Green. Even Ones Not Cabled To Anything.
I have come across two NME-16ES-1G switch modules that all port status leds are green.. Even ones not cabled to anything. Switch seems to be operator normal other than that. Any Ideas?
Current Answers
Related Cisco NME-16ES-1G Manual Pages
User Guide - Page 3
... a single workstation or server, or to a hub through which workstations or servers connect to the bandwidth. Note Default parameters on an Ethernet switch network module can either receive or transmit. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
3 Because each interface as a router or a switch. Normally, Ethernet operates in its own 10-, 100-, or...
User Guide - Page 8
... and its traffic is transferred to which the client is a Switched Port Analyzer (SPAN) destination port. using the destination MAC address always chooses the same link in the EtherChannel.
• An EtherChannel will not form if one of an EtherChannel.
and 36-Port Ethernet Switch Module for the formation of the remaining interfaces in the channel; After...
User Guide - Page 9
... Windows XP operating system. (The client is the only supported authentication server; 16- The workstation must support EAP within the native frame format. The switch includes the RADIUS client, which secure authentication information is exchanged between the client and the authentication server, requesting identity information from the switch. and 36-Port Ethernet Switch Module for...
User Guide - Page 11
... flow normally.
When a client logs off, it sends an EAPOL-logoff message, causing the switch port to change to authenticate.
and 36-Port Ethernet Switch Module for the client to authorized, and all ingress and egress traffic except for a fixed number of the client and begins relaying authentication messages between the client and the authentication server. 16...
User Guide - Page 21
...configured as Layer 2 access ports)
Ethernet: 100
Gigabit Ethernet: 19 when operated in 100-Mb mode, and 4 when operated in increments of a loop, spanning tree considers port cost when selecting an ... -interface basis; 16-
You can assign lower cost values to interfaces that you want spanning tree to put into the forwarding state. and 36-Port Ethernet Switch Module for all interfaces ...
User Guide - Page 22
... you want spanning tree to normal STP rules. and 36-Port Ethernet Switch Module for the configured maximum aging time specified by the spanning-tree max-age global configuration command. An inferior BPDU identifies one or more alternate paths can still connect to Switch B is 0 to Switch C over link L2. If one switch as a trunk port. The interface on the...
User Guide - Page 24
.... The show monitor session SPAN session number command displays the operational status of source interfaces.
One or more interfaces and to one SPAN session with the normal operation of already known devices, in the specified VLANs are neighbors of the switch.
and 36-Port Ethernet Switch Module for network traffic analysis. SPAN sessions do not interfere with separate...
User Guide - Page 40
...applications are centrally located at the same time.
and 36-Port Ethernet Switch Module for Voice, Video, and Integrated Data (AVVID) solution. By default, per-port storm-control is a section describing the default settings on ... AVVID Architecture
This section describes the Ethernet switching capabilities of the Ethernet switch network module, which the switch resumes normal forwarding.
User Guide - Page 42
...The bridge places source addresses in the system.
and 36-Port Ethernet Switch Module for each separately bridged (topologically distinct) network connected to two different VLANs. each VLAN has its own IP address. Another interface is forwarded on a switch. Feature Overview
16- Bridge groups on a switch.
Only one interface to a router. A bridge group is not connected to...
User Guide - Page 62
... parameters on a server at the same IP address. and 36-Port Ethernet Switch Module for 802.1x authentication.
Configuration Tasks
16-
Configuring the Switch-to-RADIUS-Server Communication
RADIUS security servers are tried in the 802.1x Port Summary section of the IP address and UDP port number creates a unique identifier, which enables RADIUS requests to be...
User Guide - Page 66
...and operational status for a specific interface, use the no dot1x multiple-hosts interface configuration command. To display the 802.1x administrative and operational status for...16- Verifies your entries. (Optional) Saves your entries in privileged EXEC mode, follow these steps to reset the 802.1x configuration to the default values with a single command. and 36-Port Ethernet Switch Module...
User Guide - Page 82
...
16-
The destination is the network or host number to 65535.
• Use TCP port names only for TCP traffic.
• Use UDP port names...Switch Module for source and source-wildcard of 0.0.0.0 255.255.255.255 or any as an abbreviation for most IP protocols.
access-list access-list-number {deny | permit | remark} protocol {source source-wildcard | host source | any} [operator port...
User Guide - Page 84
...operator port]
end show access-lists [number | name]
Displays the access list configuration.
copy running -config startup-config
Purpose
Enters global configuration mode.
In access-list configuration mode, specifies the conditions allowed or denied.
and 36-Port Ethernet Switch Module...
Returns to privileged EXEC mode. Configuration Tasks
16-
Note The log option is forwarded or ...
User Guide - Page 92
...16-
For destination, enter the network or host to create an IP extended ACL for IP traffic:
Step 1 Step 2
Command
configure terminal
access-list access-list-number {deny | permit | remark} protocol {source source-wildcard | host source | any}[operator port....255.255.255, or by placing ones in the configuration file.
and 36-Port Ethernet Switch Module for UDP traffic. The number can ...
User Guide - Page 93
...16- The match criterion is supported. Returns to classify traffic. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
93 Note You can include criteria such as necessary. Defines the match criterion to privileged EXEC mode. and 36-Port Ethernet Switch Module... source | any} [operator port] {destination destination-wildcard | host destination | any} [operator port]
class-map class-map...
User Guide - Page 94
...one...policy map class maps are defined.
and 36-Port Ethernet Switch Module for each type of profile (marking).
Note ...source source-wildcard | host source | any}[operator port] {destination destination-wildcard | host destination | any} [operator port]
policy-map policy-map-name
Step 4 class....2(8)T, and 12.2(15)ZJ
94 Configuration Tasks
16- You can exist for more information, see...
User Guide - Page 166
... of this command. This command was introduced. Displays ESWILP switch port manager debugging messages.
debug eswilp
16- Displays ESWILP filter manager debugging messages. Displays ESWILP SPAN debugging messages.
and 36-Port Ethernet Switch Module for the IGMP snooping services on the Ethernet switch network module being displayed:
Router# debug eswilp igmp
Related Commands...
User Guide - Page 170
... Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
deny (access-list configuration)
To configure conditions for a named or numbered IP access control list (ACL), use the no deny protocol {source source-wildcard | host source | any} [operator port] {destination destination-wildcard | host source | any} [operator port]
Syntax Description
source source-wildcard...
User Guide - Page 204
...being sent, specified in one of the network or...Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
permit (access-list configuration)
To configure conditions for a named or numbered IP access control list (ACL), use the no permit protocol {source source-wildcard | host source | any} [operator port] {destination destination-wildcard | host source | any} [operator port...
User Guide - Page 218
...frames that have been received.
Multiple Hosts Current Identifier1
Setting of the client, if one exists. This field and the remaining fields in the example.
The following is incremented...
Status
Status of the port (authorized or unauthorized). and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Table 20 show dot1x
16-...
Similar Questions
Cisco Nme-x-23es-1g Initial Configuration
Following instructions in Cisco online docs. I set the ip address for gi 1/0 and attempt to connect ...
Following instructions in Cisco online docs. I set the ip address for gi 1/0 and attempt to connect ...
(Posted by droberts4 11 years ago)
Nme-x-23es-1g Initial Configuration
I am unable to contact the module: GW12#service-module gi 1/0 session % telnet connections not per...
I am unable to contact the module: GW12#service-module gi 1/0 session % telnet connections not per...
(Posted by droberts4 11 years ago)
How I Should Real On A Switch Device/slot/port Who Is Who
I have some switches in stack fasion and other as single switch and the way to name the interfaces i...
I have some switches in stack fasion and other as single switch and the way to name the interfaces i...
(Posted by JEPA 11 years ago)
How Do I Set Poe Of 24 Ports,15.4w Or 48 Of 7.7w In The 48ps Model? Any Default?
How do I set PoE of 24 ports,15.4W or 48 of 7.7W in the 48PS model? Any default?
How do I set PoE of 24 ports,15.4W or 48 of 7.7W in the 48PS model? Any default?
(Posted by rebeca 11 years ago)
How To Resolve Port Suspended Issue On Nme-16es-1g?
Cisco NME (NME-16-ES-1G) card fatst ethernet port goes down after soem idel tiem. due to this the po...
Cisco NME (NME-16-ES-1G) card fatst ethernet port goes down after soem idel tiem. due to this the po...
(Posted by mmsundara 13 years ago)