Canon PIXMA MX882 Support Question
Canon PIXMA MX882 Support Question
Find answers below for this question about Canon PIXMA MX882.Need a Canon PIXMA MX882 manual? We have 3 online manuals for this item!
Question posted by piia on February 10th, 2015
Manual Selection
Printer says error has occurred and to consult manual. Which manual do I download?
Current Answers
Answer #1: Posted by TommyKervz on February 11th, 2015 3:48 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
The "Getting Started" manual if you need instructions on how to use or set-up your printer.
The "Network Setup Troubleshooting" for network configuretions
Download the manuals here http://www.helpowl.com/manuals/Canon/PIXMAMX882/68077
Related Canon PIXMA MX882 Manual Pages
Network Setup Troubleshooting - Page 2
... entered access point was not detected. P.7
The Machine is Not Displayed (Detected)
P.7
Check Printer Settings dialog box is Displayed Failed to connect to the access point. Find a description related to...symbols are used in this manual depending on your problem and follow the solution. Screens are enabled.
For problems not described here or which occur after the Network Environment ...
Network Setup Troubleshooting - Page 4
... how to check the WEP key of the machine, press the Setup button, then using the { } [ ] and OK buttons, select Device settings > LAN settings > Confirm LAN settings > WLAN setting list to the manual
supplied with the access point or contact its manufacturer. Check the WEP key (hexadecimal) created automatically on the access...
Network Setup Troubleshooting - Page 5
... when the access point is configured to communicate using multiple access points
Select Use multiple AccessPoints.
• For subsequent operations, go to the manual supplied with the same name are found. If the encryption standard of specific wireless devices (computers, printers, etc.) to the access point beforehand. When you have only one access...
Network Setup Troubleshooting - Page 6
...11.
Change the security protocol (encryption standard) for the access point, refer to the manual supplied with the access point or contact its manufacturer. is Displayed
Check
The message appears... then using the { } [ ] and OK buttons, select Device settings > LAN settings > Confirm LAN settings > WLAN setting list to the manual supplied with the access point or contact its manufacturer.
...
Network Setup Troubleshooting - Page 7
... procedures in the printed manual: Getting Started. Multiple ...selecting "WEP" as the security protocol for a while, then configure the settings again. Perform setup again by saving the MAC addresses of the machine.
• For details on page 11.
Connection failed. Check 2
If the DHCP function is Displayed
Check
The message appears when an error occurs... printers, etc.) to the access ...
Network Setup Troubleshooting - Page 8
...manually, refer to "Wireless Setup Using Easy Setup" in the printed manual: Getting Started.
• Check Check the printer settings (B), click Next (C), then click Wireless LAN Setup Information on the Check Printer...Problems during Software Installation
• When using the { } [ ] and OK
buttons, select Device settings > LAN settings > Confirm LAN settings > WLAN setting list or LAN setting...
Network Setup Troubleshooting - Page 9
...of the machine, press the Setup button, then using the { } [ ] and OK buttons, select Device settings > LAN settings > Confirm LAN settings > WLAN setting list or LAN setting list to ... device, refer to the manual supplied with specified IP addresses.
• DHCP function A function to automatically assign required information (IP address, etc.) to computers, printers or other devices connected to...
Network Setup Troubleshooting - Page 10
... settings of the machine, press the Setup button, then using the { } [ ] and OK
buttons, select Device settings > LAN settings > Confirm LAN settings > WLAN setting list or LAN setting list. Wireless LAN...device (router, access point, etc.)?
• For details on the Check Printer Settings dialog box to the manual supplied with the network device or contact its manufacturer.
• To check ...
Network Setup Troubleshooting - Page 11
Character Entry
Action
This machine allows you want to the manual supplied with the
access point or contact its manufacturer. The Machine is Not ...is Changed
Check
Wait until the IP address is assigned to enter characters when an on-screen keyboard is switched among them.
2 Select a character on the on-screen keyboard using the { } [ ] buttons (B), then press the OK button to enter it...
Network Setup Troubleshooting - Page 13
... manual supplied with TKIP set to
on
page 13.
• When WEP 40 bit or WEP 128 bit is selected in the screen.
Change
the encryption type to the selected security protocol. Selecting ... numbers will disable the connection between the machine and AirPort.
2 Press the OK button.
10 Select a security protocol for entering the access point name/network name (SSID).
9 Make sure that of...
Network Setup Troubleshooting - Page 14
....
1 Press the Setup button. 2 Select Device settings, then press the OK button. 3 Select LAN settings, then press the OK button. 4 Select Other settings, then press the OK button. 5 Select IPv4/IPv6 setting, then press the OK button. 6 Select IPv4, then press the OK button. 7 Select Yes, then press the OK button. 8 Select Manual setup, then press the OK...
Network Setup Troubleshooting - Page 15
...restored to the default state.
1 Press the Setup button. 2 Select Device settings, then press the OK button. 3 Select LAN settings, then press the OK button. 4 Select Reset LAN settings, then press the OK button. 5 Select Yes, then press the OK button. 6 Make sure that the... following the procedures in "Wireless Setup" and onward or "Wired
Setup" and onward in the printed manual: Getting Started.
Network Setup Troubleshooting - Page 17
...using a router, are the Ethernet cables of the printer and computer connected to the LAN side of your ...the printed manual: Getting Started.
Perform setup by following the procedures in "Wired Setup" and onward in the printed manual: Getting Started...safely. Check 6
When using the { } [ ] and OK buttons, select Device settings > LAN settings > Change wireless/wired > Wireless LAN active to ...
Network Key - Page 2
>
Obtaining Your Network Key
PIXMA MX882 Windows OS
Introduction
3
Download the Canon PIXMA Wireless Setup Assistant
4
Using the Canon PIXMA Wireless Setup Assistant
6
Troubleshooting
10
2
Network Key - Page 3
Screen to select an Access Point
Screen to enter passphrase
Screen to enter WEP key
NOTE: The Wireless Setup Assistant is supported on the following screens are unable to proceed to retrieve the access point name / network name (SSID), or the network key (WEP key / passphrase) using the Canon PIXMA Wireless Setup Assistant...
Network Key - Page 4
... the number of applications to be copied (installed) to the Drivers & Software for your model
Step Two
Select your operating system in the Select OS dropdown menu.
4 Download the Canon PIXMA Wireless Setup Assistant
>
Download the Canon PIXMA Wireless Setup Assistant
To use the machine by connecting it to a computer, software including the drivers needs to...
Network Key - Page 5
... file CanonAPChkTool. *File name will appear red when mouse pointer is being saved.
5 Download the Canon PIXMA Wireless Setup Assistant
>
Step Three
In the Software section, click the link to "Save" the file. Step Four
On the next screen, read the information ...
Network Key - Page 6
Using the Canon PIXMA Wireless Setup Assistant
>
Using the Canon PIXMA Wireless Setup Assistant
Step One
Display the window for selecting access point using the buttons on the LCD screen. Please refer to the Getting Started Guide if you are unable to enter WEP key
6
Screen to select Access Point
Screen to enter passphrase
Screen to display the below window on the printer.
Network Key - Page 8
... letters A to F in the window are the same as -is launched.
2. Then, write down as the ones in the Access Points window displayed on the printer unit (Step One).
3. Write the number down the Network Key of the access point. Confirm that the access point names listed in addition to numbers...
Network Key - Page 9
Press the left function key (End setup).
>
Step Six
When the completion screen appears, press the OK button.
9 When the window for selecting access point of the printer unit, select the access point specified in Step Four.
3. In the window for entering the network key is displayed, enter the key you copied in the step 4.
2. Using the Canon PIXMA Wireless Setup Assistant
Step Five
1.
Similar Questions
My Printer Says Error 311 And The Amber Light Keeps Flashing. Help
(Posted by kimssub 10 years ago)
Lost Setup Cd For Canon Mx882 Printer. Where Can I Get One Or Download
(Posted by rplayfor 10 years ago)
Setting Up Pixma Mx892 Printer Saying Error No Paper What To Do
(Posted by tritonio 10 years ago)
Paper Jam Was Cleared But Printer Says The Cartridge Needs Paper.
I've only had the Canon Pixma mx882 for a few weeks. It had a paper jam in the back of it. I removed...
I've only had the Canon Pixma mx882 for a few weeks. It had a paper jam in the back of it. I removed...
(Posted by bobshulkind 12 years ago)