Brother International S-7200B Support Question
Brother International S-7200B Support Question
Find answers below for this question about Brother International S-7200B.Need a Brother International S-7200B manual? We have 7 online manuals for this item!
Question posted by dcddilan on September 29th, 2015
Error 2
Hai,Our Brother S-7200A-403 machine when we press foot pedal - displaying ERROR 2. we check trouble shooting pages. that mentioned CN7 or CN8 not properly connected. then we was removed and reconnect properly. but still same problem. please kindly help me. ThanksBest RegardsDilan
Current Answers
Answer #1: Posted by TommyKervz on September 30th, 2015 7:17 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,843
Member since:
January 10th, 2013 Points: 17,776,843
See the service manual on page 76 from the link below
http://www.manualslib.com/manual/442002/Brother-S-7200b.html?page=76&term=error&selected=2
Related Brother International S-7200B Manual Pages
Basic Instruction Manual - English - Page 1
S-7200B
Basic Operation Manual
SINGLE NEEDLE DIRECT DRIVE STRAIGHT LOCK STITCHER WITH THREAD TRIMMER
Please read this manual within easy reach for quick reference. Please keep this manual before using the machine. This basic operation manual describes basic operations including sewing machine operations.
For cleaning, standard adjustments and more details, please refer to the instruction...
Basic Instruction Manual - English - Page 2
... these parts. S-7200B Before using your new machine, please read the safety instructions and the explanations given in front of moving parts such as the needle and thread take-up, and consequently there is normal to use it is always a danger of injury that you very much for buying a BROTHER sewing machine. Thank you will...
Basic Instruction Manual - English - Page 4
...operation.
The installation should be within ±10% of the machine head may cause your hand to slip, and your Brother dealer or a qualified electrician for any electrical work table which... wall outlet before inserting or removing the plug, otherwise damage to the control box could result in injury.
CAUTION
Environmental requirements
Use the sewing machine in such a way so that...
Basic Instruction Manual - English - Page 5
...7200B
iii CAUTION
Sewing
This sewing machine should only be used by operators who have been removed, be absolutely sure to re-install them to their original positions and check that they operate correctly before using the sewing machine... the weight of the sewing machine should only be carried out by Brother.
Turn off the power switch. Use only the proper replacement parts as the ...
Basic Instruction Manual - English - Page 6
...-up cover
Oil pan
Control box
iv
S-7200B
3629M Please follow the instructions on the sewing machine. [3] Warning labels
The following warning labels appear on the labels at all times when using the machine. If the labels have been removed or are difficult to read, please contact your nearest Brother dealer.
1
2
3
Be sure to connect the ground.
Basic Instruction Manual - English - Page 10
...machine head.
3631M
Returning the machine head to be done. Operation problems may be carried out by electronic interference from the sewing machine. 3. Contact your foot...your Brother dealer or a qualified electrician for any tools, etc. INSTALLATION
CAUTION
Machine ...7200B About the machine set-up location
Do not set up this sewing machine near the table holes. 2. Do not connect...
Basic Instruction Manual - English - Page 11
... [3 pcs] (4) Spring washers [3 pcs] (5) Washers [3 pcs]
2. Connecting rod
(6) Connecting rod (7) Nut
2091M
S-7200B
4 Table processing diagram
The top of the table should be 40 mm in the illustration below. Drill holes as indicated in thickness and should be strong enough to hold the weight and with-stand the vibration of the sewing machine. Installation
2090M
1.
Basic Instruction Manual - English - Page 15
...machine head. 3. When cutting the nozzle of the oil tank, hold the end of children. VG10) specified by mistake, which could result in the oil gauge window (5). Upper reference line
Lower reference line
3641M
S-7200B
8 3.
Hold the base of non-use is necessary. Be sure to its original position. 6. Remove...sewing machine is -[]5[] specifications, it is depressed by Brother....
Basic Instruction Manual - English - Page 16
...Brother dealer or a qualified electrician for any electrical work that may also occur.
3-4-1. The machine may operate if the treadle is not secure, you run a high risk of the control box. Connecting...to connect the ground. Be sure to be done. Connecting the cords
3642M
1. Sewing machine cords
3643M
9
S-7200B Do not connect the power cord until all cords have been connected. ...
Basic Instruction Manual - English - Page 17
... control box should be secured to the cord holder (3) using the repeat cable tie (1), otherwise vibration from the sewing machine may cause the cords to become disconnected, which can cause problems with operation panel) (3) 14-pin encoder connector (4) 14-pin machine connector
Refer to the following page for the 4-pin motor connector.
3131M
3132M
2.
Instruction Manual - English - Page 5
... applications other than sewing. S-7200B
iii
The machine may operate if the treadle is used without these devices attached, injury may cause your hand to slip, and your Brother dealer or a qualified electrician to their original positions and check that they can result. If only one hand is depressed by the warranty. The sewing machine should be...
Instruction Manual - English - Page 70
... the temperature protection has activated. Turn the power switch off and then back on the display when the sewing machine has been operating continuously for 3 minutes or more. This is a problem communicating with the operation panel
CPU.
(Panel communication error)
Is the operation panel connector inside the control box disconnected? board. 14. Insert the...
Instruction Manual - English - Page 71
... with the thread trimming mechanism.
**
solenoid timeout)
Err 18
(EEROM error)
This is displayed if the sewing machine motor locks during thread trimming.
Replace the head detector unit.
14.
Remove any thread scraps that there are no problems with control P.C.
Replace the treadle unit.
**
S-7200B
64 board. C. Replace the control box. board.
Replace the control...
Instruction Manual - English - Page 72
...procedure being carried out).
Page *
3159M
Err 100
This appears on the display when the sewing machine has continued to OFF.
*
3160M
If an error code that is not ...listed above appears or if carrying out the specified remedy does not solve the problem, contact the place of purchase.
65
S-7200B...
Instruction Manual - English - Page 73
....
12
Solenoid power supply error
13
Treadle unit error
14
Head detector unit error
15
Problem with sewing machine motor operation
16
Thread trimming solenoid timeout
18
EEROM error
19
Control box overheating
20
Treadle pedal position error
21
Thermistor error
If an error code that is displayed on the control box panel, this will be checked by a qualified technician. Apply...
Service Manual - Page 5
... the machine. Use only the proper replacement parts as specified by operators who have been removed, be absolutely sure to re-install them to carry out any maintenance and inspection of the moving parts or press any objects against the machine while sewing, as this may result in injury. The sewing machine should only be used by Brother.
Then...
Service Manual - Page 77
....
49
3154M
This appears on again, and then operate the sewing machine normally. After the temperature has dropped, turn on the power switch.
board. Page 52
Err 6
(Voltage drop)
Is the machine head tilted back?
Check the power supply voltage.
54
Err
7
This is displayed when there is overcurrent in any of the solenoids (thread trimming...
Service Manual - Page 78
....
Page 53
49
3702M
52
3158M
52
Err 15
(Problem with sewing machine motor operation)
Err 16
(Thread trimming solenoid timeout)
Err 18
(EEROM error)
Err 19
(Control box overheating)
Err 20
(Treadle pedal position error)
Problem with power P.C. Problem with motor. Remove any thread scraps that there are no problems with control P.C. This is displayed if the sewing machine...
Service Manual - Page 79
... the reset procedure.
44
Err 101
Is DIP switch No.4 inside the control box disconnected?
TROUBLESHOOTING Page 52
3159M
Err 100
This appears on the display when the sewing machine has continued to OFF.
4
3160M
If an error code that is not listed above appears or if carrying out the specified remedy does not solve...
Service Manual - Page 80
... cause If you continue to these error codes.
12
Solenoid power supply error
13
Treadle unit error
14
Head detector unit error
15
Problem with sewing machine motor operation
16
Thread trimming solenoid timeout
18
EEROM error
19
Control box overheating
20
Treadle pedal position error
21
Thermistor error
If an error code that is displayed on the control box panel, this...
Similar Questions
Price Quotation
Hi!I would like to know the prices of each model of Brother Sewing machine?S7200B-405SL777B-3T8420B-...
Hi!I would like to know the prices of each model of Brother Sewing machine?S7200B-405SL777B-3T8420B-...
(Posted by russeltizon 6 years ago)
Does Sewing Machine Without Foot Pedal Have Optional Foot Pedal?
(Posted by micPoetaL 10 years ago)
Brother Ls 2000 Sewing Machine Price
I Want To Know Above Sewing Machine Price In Indian Rupees,please Anser Me Imediately
I Want To Know Above Sewing Machine Price In Indian Rupees,please Anser Me Imediately
(Posted by iladave84503 10 years ago)
How To Solve Error Problem?
When i started machine it comes error 06, How to solve it ?
When i started machine it comes error 06, How to solve it ?
(Posted by kgourva79 10 years ago)