Brother International PE 150 Support Question
Brother International PE 150 Support Question
Find answers below for this question about Brother International PE 150 - Emboidery Machine.Need a Brother International PE 150 manual? We have 1 online manual for this item!
Question posted by dmcqx2 on October 25th, 2015
My Needle Broke When My Thread Jammed. Now The Needle Is Too Far To The Left
The person who posted this question about this Brother International product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Brother International PE 150 Manual Pages
Users Manual - English - Page 2
... being administered. 8. Use only accessories recommended by the manufacturer as contained in the needle
area, such as threading needle, changing needle, threading bobbin, or changing presser foot, and the like. 15. Never operate the embroidery machine with same type rated 2.4 watts. Do not operate where aerosol (spray) products are being used or where oxygen is used...
Users Manual - English - Page 4
... wheel, thread take-up, needle, or other parts to assure correct installation.
Benzene, thinner, and scouring powders can damage the case and machine, and should never be sure to change for improvement without
notice.
1 If the problem persists, please consult your machine turns on the needle while sewing. CONGRATULATIONS ON CHOOSING OUR COMPUTER EMBROIDERY MACHINE
Your machine is...
Users Manual - English - Page 5
...THREADING 16 Auto needle threading device 17 PREPARATION BEFORE EMBROIDERING 18 Attaching stabilizer material 18 Embroidering different types of fabric 18 Setting the fabric in the embroidery frame 20 Fitting the embroidery frame to the machine 22 Removing the embroidery frame ...... 22 THREAD... Changing thread density of the stitch on characters and some frame patterns ... 47 SEWING A BASIC...
Users Manual - English - Page 6
...threader 8- Hole for extra spool pin 16- MAIN POWER SWITCH AND CONNECTORS B- Balance wheel 14- Upper thread tension dial 5- Bobbin winding device 12- Carriage (Embroidery arm)
16
A- SELECTION KEYS C- Bobbin winding guide 4- Presser foot 9- Needle plate 11- "START/STOP" BUTTON
EMBROIDERING USING A
EXTRA-SMALL FRAME (OPTIONAL)
EMBROIDERING USING A LARGE
FRAME (OPTIONAL...
Users Manual - English - Page 9
...).
***** Distributed in some countries.
** An extra spool pin should be used for decorative thread such as metallic thread.
*** If using special threads which wind quickly off the thread spool, attach a net to the spool before using.
**** In some countries, the No. 14 machine cover is still attached, touch "CHARACTERS & DESIGNS" or "CARD" to return the...
Users Manual - English - Page 13
... be displayed. 1 "BASIC OPERATION" key
Example: To find out how to wind a bobbin
1. CONTENTS
MACHINE KNOWLEDGE
EMBROIDERING MAINTENANCE
ERROR MESSAGE
TROUBLESHOOTING
Example: To find out the combination of fabric, needle and thread
1. Touch "FABRIC AND THREAD AND
NEEDLE". 2 "MODIFY & ADVISE" key
10
PATTERNS
EMBROIDERING USING A SMALL
FRAME (OPTIONAL)
EMBROIDERING USING A
EXTRA-SMALL...
Users Manual - English - Page 18
...Guide the thread end around the finger through the channel toward the back, pulling the thread toward you which will cut off any excess. CONTENTS
MACHINE KNOWLEDGE
Setting ...thread direction as noted in front of the needle plate.
1. Embroidery can begin without pulling out the lower thread.
15
EMBROIDERING USING A LARGE
FRAME (OPTIONAL) Slide open the bobbin cover by placing the left...
Users Manual - English - Page 19
... use a 90/14
home sewing machine needle.
1 Insert the extra spool pin into the hole on the top of the machine
2 Spool felt 3 Thread spool
NOTE This method keeps the thread from the front of the machine. 2.
Guide the thread as it so that you start embroidering.
Thread the needle using metallic thread, we recommend that the thread
winds off the spool...
Users Manual - English - Page 20
... threader lever.
7. Lower the presser foot. 3. Push the needle threader lever toward you .
2. While gently holding the thread, pull the needle threader lever forward. CONTENTS
MACHINE KNOWLEDGE
EMBROIDERING MAINTENANCE
1 4
2
3
4
Auto needle threading device
6
Net If using special threads which wind quickly off the thread spool, attach a net to the spool before using. * Cut the net to...
Users Manual - English - Page 28
... USING A
EXTRA-SMALL FRAME (OPTIONAL)
EMBROIDERING USING A LARGE
FRAME (OPTIONAL)
1 2
Checking for a bent needle 1 Place the needle on . Turn the balance wheel to raise the needle to your project or the machine.
25 Insert the new needle into the needle shaft as far up as it by firmly tightening the screw with a screwdriver.
5. Turn the power switch...
Users Manual - English - Page 31
... MAINTENANCE
Start embroidering
1. After threading the needle, pass the thread from the top to the bottom through the hole of the presser foot, and gently pull the end of the design. After sewing 5 - 6 stitches, stop sewing when it has completed all the stitching with the current thread color. The machine will stop the machine and raise the presser...
Users Manual - English - Page 32
...
FRAME (OPTIONAL)
EMBROIDERING USING A
EXTRA-SMALL FRAME (OPTIONAL)
EMBROIDERING USING A LARGE
FRAME (OPTIONAL)
29 CONTENTS
MACHINE KNOWLEDGE
Embroidering advice
Thread Embroidery thread #50
Needle
Home sewing machine needle 75/11
* The recommended lower (bobbin) thread is #60 - #90 synthetic thread.
* For thin and stretch fabrics which are difficult to embroider, attach the fabric to non...
Users Manual - English - Page 48
...˚ steps as shown in the illustration at the starting point
1.
CONTENTS
MACHINE KNOWLEDGE
EMBROIDERING MAINTENANCE
Embroidering from getting very close to the edge of the presser...the frame as the presser foot prevents the needle from a specific starting position on the fabric in the frame as shown in the illustration. Make a mark at left each time "90˚ clockwise" is ...
Users Manual - English - Page 53
... embroidering has finished, the machine will sew the finishing position automatically. ...left edge of the frame.
1 Finishing position 3. Input "ABC", then touch "SET" and then "LAYOUT". After this, touch "START/ CENTER" to switch to embroider and you cannot embroider them all in large size
1. Input the remaining letters "DE", and then
touch "START/CENTER" to start point
of the needle...
Users Manual - English - Page 61
... 4
4.
O 6. CONTENTS
MACHINE KNOWLEDGE
CLEANING
Always keep the machine clean.
1. Loosen the screws on the needle plate. 3. Remove the needle plate. Take out the inner ...needle, and then raise the presser foot lever.
1 Use a screwdriver to loosen the screw to spring of the stopper.
1 Projection of the hook 2 Spring of the hook next to remove.
2. Remove any accumulated lint and threads...
Users Manual - English - Page 62
... the presser foot lever is pressed. This message is displayed when the machine senses that the upper or lower thread has broken or no pattern stored in your operation is required, machine will not start and will instruct you to raise the needle to the highest position. Warning message displays
This message is displayed...
Users Manual - English - Page 63
... #1, the Alphabet card and #10, Monogram emblem card, can be saved into the machine's memory.
Use the balance wheel to move the embroidery frame while the needle is made to change the thread color.
If you are not changing the thread color, raise the presser foot lever, lower it again, and then press the...
Users Manual - English - Page 65
... A LARGE
FRAME (OPTIONAL)
62 Trouble with 3. Clean the race or inner rotary hook.
3.
The needle is too strong. 1. The embroidery frame has been attached to the machine correctly.
5. The upper thread tension is not correctly inserted.
1. The correct needle is being used . The spool of the instruction book which explains the operation you are...
Users Manual - English - Page 66
... than the designated
4. Increase the upper thread tension using the upper thread tension dial.
2. no stabilizer fabric attached.
4. Remove the needle plate and clean away the accumulated thread. A thread other than the designated
3.
Attach the embroidery frame to the machine correctly.
3. The needle threader lever will not turn. 2. Lower thread is visible on the top...
Users Manual - English - Page 67
... power comes back on and select an operation. Damage may occur if the machine is equipped with a brush. 1. The needle breaks
Probable cause
1. Check Error messages.
1. Remove the needle and reset a new
needle properly. 2. Accordingly, if the upper thread is
not threaded, the machine will not operate even if the "START/STOP" button is not correctly inserted...
Similar Questions
Needles And Thread
Why does my pe150 keep breaking needles and why does the top thread keep breaking
Why does my pe150 keep breaking needles and why does the top thread keep breaking
(Posted by Cbriggs52 10 years ago)
Usage Of Bigger Thread Spool/bobbin For Lower Needle On Bas-342e Machines.
We use BAS-342E- machines to sew mesh on mops. The bobbin for the lower needle needs to be changed v...
We use BAS-342E- machines to sew mesh on mops. The bobbin for the lower needle needs to be changed v...
(Posted by janeaustenpes 11 years ago)
Keep Getting Following, Check Thread Check Needle Is Not Bent
keep getting following, check thread check needle is not bent
keep getting following, check thread check needle is not bent
(Posted by watersmary 11 years ago)
Have A Pe-150 And It Keeps Saying That The Thread Is Broken Or Th Needle Is Bent
Have a PE-150 and it keeps saying that the thread is broken or th needle is bent. Have rethreaded an...
Have a PE-150 and it keeps saying that the thread is broken or th needle is bent. Have rethreaded an...
(Posted by kkh11 12 years ago)