BenQ PB6240 Support Question

Find answers below for this question about BenQ PB6240 - XGA DLP Projector.
Need a BenQ PB6240 manual? We have 1 online manual for this item!

BenQ Overview Questions Manuals Reviews Videos Research

Question posted by Kawainrashidi on September 29th, 2014

My Benq Pb6240 Turn Off After Less Then 1min. It Won't Turn On

My benq pb6240 turn off after less then 1min. It won't turn on

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TechSupport101 on September 29th, 2014 3:54 AM

This answer was accepted by the poster of the original question.

TechSupport101

Member since:
May 24th, 2013

Points: 12,171,305

1,080
points

Hi. Possible causes

1. Bad fan(s)

2. Bad lamp

3. Other failed mainboard component.

Your manual here may be of great help with troubleshooting.

www.satechhelp.co.za

Related BenQ PB6240 Manual Pages

User Manual - Page 1

PB6240 Digital Projector Portable Series User's Manual Welcome

User Manual - Page 8

.... 12. Do not step on the projector. Safety Instructions (Continued) 11. Do not place liquids near or on the projector or place any objects when the projector is under operation as this could cause the objects to fail. To temporarily turn off the lamp, press Blank on the projector or remote control. 4 Important safety instructions...

User Manual - Page 13

... on-screen display control up or flashes when the projector is under operation. Used to page 20 for more information.) information.) Turns the projector on -screen menu is not activated, #3 and #4 function as information.) directional arrows to page 21 for the displayed Adjusts the focus of the lamp. Source (...

User Manual - Page 14

... to page 19 for more 9 information.) 5 Automatically determines the best 3 10 picture timings for more information.) Turns the projector on or off. 2. Auto (Refer to page 24 for displayed image. 9. Page Up and Down 1 Connect the projector to make adjustments. 6. Source (Refer to restore the image. An icon " " will display in the lower...

User Manual - Page 16

... behind the screen. Note that a special rear projection screen is required. I. Purchase the BenQ Projector Ceiling Mounting Kit from the ceiling in the Advance > Mirror menu after you turn the projector on . III. Note that a special rear projection screen and the BenQ Projector Ceiling Mounting Kit are required for quick setup and portability. Ceiling rear Select...

User Manual - Page 17

... tilt it down or up to center the image on the screen after turning the projector on your screen ratio. Install the projector at a proper distance from the screen. 3. Use the Keystone function to... the table of your screen (4:3 or 16:9). 2. Determine the aspect ratio of 4:3 or 16:9 Screen Size depending on . BenQ...

User Manual - Page 19

... S-VIDEO AC-INLET • A Mac adapter (an optional accessory) is capable of accepting a Component Video signal. Turn all equipment off . They are firmly inserted. Locate a function key labeled CRT/LCD or a function key with the projector (see page 6). Press FN and the labeled function key simultaneously. Use the correct signal cables for...

User Manual - Page 20

... on a monitor as well as on the screen, you can connect the RGB signal output port on the projector to an external monitor with a VGA cable. The following standards are supported in the digital TV function: &#... cable If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the signal cables have been connected ...

User Manual - Page 21

...3. If the frequency/ resolution of the input signal exceeds the projector's operating range, you are prompted for setting up , a default BenQ logo is projected. 6. Setting > Password. For details of ...for information. Switch all of start up 1. Plug the power cord into the projector and into a wall socket. Turn on . 5. Remove the lens cap. If it is started. 1. Press ...

User Manual - Page 22

...A confirmation message displays. ii. If you ever forget it , you can retry by turning off the projector (by pressing Power) and start again, or if you did not record the password in...Password Setup a prompt will display a coded number on -screen menu. Seek help from the local BenQ service center to Setting > Change Password. 2. You may be asked to enter the four digit ...

User Manual - Page 26

... cord from the wall socket. Shutdown 1. To protect the lamp, the projector will not respond to start the projector within hours, the fans will run for a few minutes to cool down , the fans continue to run for approximately 110 seconds to turn the projector off. 2. Press Power and a warning message appears. Do not unplug...

User Manual - Page 28

...4 on the remote control. 2. remote control to turn the on- Keystone. 24 Operation the projector or 3 / 4 on the projector or 5. Press 5Exit or 6Menu on the projector *The first press leads you back to the or... different menu languages. (Refer to select submenu and the second press closes the on the projector or Menu 4. Press 6 Menu on -screen menu. Adjust keystone values by on the...

User Manual - Page 33

Refer to turn on a ceiling or behind a screen, or with one or more information. Sets whether the projector searches automatically for the OSD control menus. If the function is not activated, the projector selects the last used for protecting projector from extreme environment and may cause high fan speed. Three modes are available: Default (BenQ logo...

User Manual - Page 35

..., use wax, alcohol, benzene, thinner or other parts needs replacing. These can damage the case. Transporting the projector It is to gently wipe the lens surface. The only thing you clean the case, turn the projector off and unplug the power cord. Remove the batteries from the remote control. Maintenance 31 Then wipe...

User Manual - Page 36

... hazardous waste regulations to dispose of injuries to change the lamp. Replacing the lamp • To reduce the risk of electrical shock, always turn the projector off and let the projector cool for at least 45 minutes before the projector will shutdown after 40 seconds. The lamp has been in operation for optimal performance.

User Manual - Page 37

... screw is removed. Loosen the screw that you touch the optical components inside, it stands up. If you use a magnetic-head screwdriver. Restart the projector. Maintenance 33 Turn the projector over tighten the screw. Step 2. Re-install the lamp cover and tighten the screw. Step 3. Step 5. Insert a new lamp. Step 7. Step 1. Step 4. Do...

User Manual - Page 38

... OFF 2. : Light flashing 3. : Light ON 4. process. The Power indicator light is not replaced as it is turned off and contact qualified service personnel for 5 seconds to cool down O - - Press Auto on the projector or on page 34. Turn the projector off . R : Red light 6. G : Green light Light Status & Description Power Temp Lamp Power events (1) The...

User Manual - Page 41

...selected. Remedy Plug the power cord into the power outlet. Troubleshooting THE PROJECTOR DOES NOT TURN ON. The projector is still attached to the lens Remedy Adjust the focus of power. The lens... cap is not correctly connected to turn the projector on or connected correctly. The projector and the screen are too far away from the power cable. If the...

User Manual - Page 42

Specifications Projector specifications All specifications are subject to 29.1 mm 250W lamp Power supply Power ...176;C ~ 40°C at 23°C 38 Specifications General Product name Model name Optical Digital Projector PB6240 1024 x 768 XGA Display system Lens F/Number Lamp Electrical 1-CHIP DMD PB6240 F=2.4 to 2.6, f= 24.0 to change without condensation) 6000 feet at 30°C 6000 ~...

User Manual - Page 46

... an experienced radio/TV technician for EMC (Electronic Magnetic Compatibility) and fulfills these requirements. However, there is encouraged to try to correct the interference by turning the equipment off and on a circuit different from that interference will not occur in accordance with the instructions, may cause harmful interference to radio communications...