eMachines T3065 Support and Manuals
Get Help and Manuals for this eMachines item
View All Support Options Below
Free eMachines T3065 manuals!
Problems with eMachines T3065?
Ask a Question
Free eMachines T3065 manuals!
Problems with eMachines T3065?
Ask a Question
Popular eMachines T3065 Manual Pages
User Guide - Page 39
... to continue. message appears, replace the Restore CD
#2 with #2 in the Restore CD #1 will be copied to your hard disk. 8. Using the Restore CDs 5-3 And press Enter to continue. 9. 7. The restoration process will appear. When the "Insert next media and press enter to install a driver. NOTE Depending on the model, your
personal information. After...
NG3 Hardware Reference - Page 57
... home or office. Important
Check local code requirements before installing Ethernet cable or other wiring in your home or office. A DHCP network configuration uses a router to automatically assign IP addresses to set up an Ethernet network is Dynamic Host Control Protocol (DHCP) using Standard or Fast Ethernet components. Standard Ethernet runs at 10 Mbps, Fast Ethernet runs at 100 Mbps, and...
NG3 Hardware Reference - Page 143
... Restore my computer to -resolve software problems, you can restore your system running again. Every time you install new device drivers or software, and every 24 hours (while your computer is turned on), Microsoft System Restore takes a "snapshot" of your computer with System Restore. To restore using eMachines System Recovery, you should try Microsoft...
NG3 Hardware Reference - Page 183
... the AC outlet is supplying power.
■ If you followed each instruction.
■ If an error occurs in the Search box, then
click the arrow.
Type the keyword troubleshooting in a program, see "Preventing static electricity discharge" on and while the modem cable, network cable, and power cord are connected.
■ Make sure that you...
NG3 Hardware Reference - Page 187
... 11 or your Internet service provider (ISP) is plugged into the Ethernet network jack and not the modem jack. Contact your setup poster to make sure that the modem cable is set up modem, make sure that you are using a cable or DSL modem, make sure that the connections have a problem with your setup poster to make...
NG3 Hardware Reference - Page 188
...driver. Let the keyboard dry before using an aerosol can of graphics and multimedia on Web pages
■ Having multiple Web browsers open, performing multiple downloads, and having multiple programs open the browser. If the error...lost your Internet connection, or your ISP is set up correctly. www.emachines.com
Troubleshooting
Help and Support
For more information, see the poster that ...
NG3 Hardware Reference - Page 190
www.emachines.com
Troubleshooting
■ Age of display device you are using a VGA or an S-Video display device and automatically changes the display settings for viewing and using the ...on a non-Media Center computer that were recorded with Service Pack (SP) 1 or 2, Windows Media Player 9 or later, and the Windows patch Q810243 Update. The Media Center saves recorded programs in a fuller...
NG3 Hardware Reference - Page 191
... see "Manually updating the Media Center Program Guide" on page 180. CHAPTER 14: Troubleshooting
www.emachines.com
You get the correct code to the Media Center computer. See also "Internet" on page 19.
See "Connecting the dial-up )
184
Drive letters for a dial tone by plugging a working telephone into the modem jack and not the Ethernet network jack...
NG3 Hardware Reference - Page 192
...sounds). Dial a single number (such as line noise, telephone service provider equipment, or ISP limitations, may lower the speed even further. Make sure that the connectors are free... the
arrow.
www.emachines.com
Troubleshooting
Help and Support
For more information about troubleshooting, click Start, then click Help and Support. The problem may not support 48K uploads.
185 ...
NG3 Hardware Reference - Page 193
... you get an error such as port already open programs.
2 Click Start, then click Control Panel.
If information about troubleshooting, click Start, then click Help and Support. Handshaking is a...problems with no data, or if you want to make sure that the connections have a 56K modem
Current fax technology only supports a maximum send and receive rate of 14,400 bps. If the handshaking sounds...
NG3 Hardware Reference - Page 194
... bent or damaged pins. ■ Reinstall the device driver. ■ Connect a monitor that :
■ ...part of your computer. ■ Check the cable for at least 30 minutes before making a final judgment about troubleshooting, click Start, then click Help and Support... degauss feature. www.emachines.com
Troubleshooting
4 Click the Modem tab, then adjust the Speaker volume control. 5 Click OK ...
NG3 Hardware Reference - Page 195
...
box, then click the arrow.
CHAPTER 14: Troubleshooting
www.emachines.com
Tips & Tricks For more information, see "Adjusting the screen and desktop settings" on your computer. Most routers have the same workgroup name.
188 For more information about troubleshooting, click Start, then click Help and Support. For more information, see "Networking Your Computer" on .
Mouse
The mouse...
NG3 Hardware Reference - Page 197
...set a default printer:
1 Click Start, then click Control Panel.
Help and Support
For more information about troubleshooting, click Start, then click Help and Support.
If your printer for adding additional memory. See the printer documentation for instructions for instructions...CHAPTER 14: Troubleshooting
www.emachines.com
The printer is on installing the printer driver. Most printers ...
NG3 Hardware Reference - Page 198
... order number available, along with a detailed description of your problem, including the exact text of your call. www.emachines.com
Telephone support
Sound
Help and Support
For more information, see "Configuring the audio jacks" on page 23.
■ Make sure that mute controls are turned off. Type the keyword sound troubleshooter in securely.
■ If you have "how to...
NG3 Hardware Reference - Page 199
... site's Documentation Library.
■ This user guide. ■ The software publisher's Web site.
192
In many cases, additional product information and online documentation for eMachines-supplied hardware can access technical support through your telephone to get answers to your questions:
Resource Service description
How to reach
eMachines Customer Care
Talk to questions about using...
eMachines T3065 Reviews
We have not received any reviews for eMachines yet.