ZyXEL UAG2100/4100 Support and Manuals
Get Help and Manuals for this ZyXEL item
This item is in your list!
View All Support Options Below
Free ZyXEL UAG2100/4100 manuals!
Problems with ZyXEL UAG2100/4100?
Ask a Question
Free ZyXEL UAG2100/4100 manuals!
Problems with ZyXEL UAG2100/4100?
Ask a Question
Popular ZyXEL UAG2100/4100 Manual Pages
User Guide - Page 21
..., this guide may be part of the LAN1 or LAN2.
1.2 Default Zones, Interfaces, and Ports
The default configurations for your model.
Figure 1 Zones, Interfaces, and Physical Ethernet Ports
UAG2100 / UAG4100... set up multiple networks for zones, interfaces, and ports are as follows. The UAG lets you set ports to interfaces may use "the WAN interface" rather than the specific ...
User Guide - Page 50
... Installation Setup Wizard - See the feature-specific chapters in each field. Refer to information provided by your ISP to know what to enter in this screen to its default configuration, the Installation Setup Wizard screen displays. This chapter provides information on configuring the Web Configurator's installation setup wizard. Leave a field blank if you reset the UAG to set...
User Guide - Page 82
...UAG Series User's Guide
82
Use Widget Setting to identify the UAG...the VPN tunnels that supports IPSec VPN.
Each ...update the widget's information immediately. See Section 6.2.4 on what type of each interface or device installed...firmware.
The first MAC address is assigned to physical port 1, the second MAC address is .
Down -
Model Name This field displays the model...
User Guide - Page 131
...about the log message. The Web Configurator saves the filter settings if you leave the View Log screen and return to...specific log message. Message
This field displays the reason the log message was recorded. Select a service protocol whose log messages you show the filter. Search
This displays when you would like to it is currently displayed on page 551). Refresh
Click Refresh to update...
User Guide - Page 193
...manually.
Enter the IP address of the VLAN interface. Interface Parameters
UAG Series User's Guide
193
Select this to use based on the type of VLANs you must manually...The total number of network to additionally manually configure some related settings.
The UAG sends packets to the gateway... on the model. The gateway should be up to add routing and SNAT settings for traffic ...
User Guide - Page 201
... manually configure a policy route to add routing and SNAT settings for connecting to additionally manually configure some related settings.
The UAG automatically adds default SNAT settings ... become part of the bridge interface. Table 85 Configuration > Network > Interface > Bridge > Edit
LABEL
DESCRIPTION
Show Advanced Settings / Hide Advanced Settings
General Settings
Enable Interface...
User Guide - Page 238
...Service - Original Service Mapped Service Protocol Type Original Port Mapped Port Original Start Port Original End Port Mapped Start Port Mapped End Port
Related Settings Enable NAT Loopback
This field is supported if this NAT rule supports...Original IP). This field is available if Port Mapping Type is Service. UAG Series User's Guide
238 Enter the beginning of the range of just the specified ...
User Guide - Page 371
... (s) connected to check a user name and password that is more secure.
AH does not support encryption, and ESP is possible for the UAG...Guide
371 Transport mode is only used when the IPSec SA is wrong, the routers do not have established the IKE SA, they can set... to authenticate each packet. You can set up the UAG to provide a user name and password to the remote IPSec router, or you...
User Guide - Page 420
...Setting > Edit
UAG Series User's Guide
420 Click Reset to return the screen to its last-saved settings.
34.4.1 Default User Settings Edit Screens
The Edit User Default Settings screen allows you to set to use the default settings...unsuccessfully (for example, wrong password) before the IP address is locked out for the selected type of time.
User Lockout Settings Enable logon retry limit
...
User Guide - Page 448
... can register your UAG and activate the service. The version number increments when signatures are updated at myZyxel.com. If your signatures.
37...update your signature set is not activated yet. This field shows the date (YYYY-MM-DD) and time the current signature version was released. Figure 299 Configuration > Object > Application > Application > Add Application Rule
UAG Series User's Guide...
User Guide - Page 502
...time server or it . Figure 336 Synchronization in the View Log screen. UAG Series User's Guide
502 screen appears, you may have been tried.
45.4.2 Time Server Synchronization
Click the Synchronize...list of NTP time servers, it is successful. To manually set the UAG date and time.
1 Click System > Date/Time. 2 Select Manual under Time and Date Setup. 3 Enter the UAG's time in the New Time ...
User Guide - Page 539
...select it and click Edit to be able to modify the entry's settings. Move
To change the server port number for a service if needed, however you must use the same port number in ...the SNMP manager when a managed AP is the password for incoming Set requests from the UAG.
To apply other configured rule.
Server tab. UAG Series User's Guide
539
Edit Remove
Double-click an entry or select...
User Guide - Page 543
...main screen. This is installed, and the utility language.
UAG Series User's Guide
543 This is not supported by the UAG at the time of writing.
11 Settings
Use this icon to ... the firmware from left to right in advance.
7 Change Admin Password
Use this icon to change the admin password of the selected device. This may be useful when troubleshooting or upgrading new firmware.
4...
User Guide - Page 597
...'s Guide
597 I cannot get Dynamic DNS to work.
• You must manually configure a policy route to add routing and SNAT settings for traffic it on top of another Ethernet interface. The UAG routes and applies SNAT for an interface with the Interface Type set to Internal or External.
This way the UAG automatically updates every...
User Guide - Page 632
... SSH 532
throughput rate troubleshooting 600
time 499
time servers (default) 502
to-Device security policy 303 and NAT 238 and remote management 303 and service control 512 global rules ...and Play 256 Application 256 security issues 257
unsafe web pages 397 updating
signatures 139 upgrading
firmware 566 uploading
configuration files 566 firmware 566 shell scripts 567 UPnP 256 usage CPU 83, 86 flash ...
ZyXEL UAG2100/4100 Reviews
Do you have an experience with the ZyXEL UAG2100/4100 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for ZyXEL yet.
Earn 750 points for your review!