Owner's Manual
Page 1
CONCERT MARIMBAS YM-460/460F/410D/410/410F YM-46/41 OWNER'S MANUAL Make sure to read "PRECAUTIONS FOR HANDLING GAS SPRING" and "PRECAUTIONS".
CONCERT MARIMBAS YM-460/460F/410D/410/410F YM-46/41 OWNER'S MANUAL Make sure to read "PRECAUTIONS FOR HANDLING GAS SPRING" and "PRECAUTIONS".
Owner's Manual
Page 2
... can collapse and/or get out of the instrument. Never hold the instrument anywhere other than the frame ends. * Approximate weights for treatment of control. 2. Doing so is a large and heavy instrument that are used in the instrument dropping or falling off , or you use the concert marimba, carefully read the instructions listed below are obeyed- Bumping into a wall, and...
... can collapse and/or get out of the instrument. Never hold the instrument anywhere other than the frame ends. * Approximate weights for treatment of control. 2. Doing so is a large and heavy instrument that are used in the instrument dropping or falling off , or you use the concert marimba, carefully read the instructions listed below are obeyed- Bumping into a wall, and...
Owner's Manual
Page 3
... and make sure to keep the manual in other problems. Retighten the screws from time to vibrations. ◆ Handling • Never place an object on the YM-410/410F/460/460F should carry out this part of the legs the fixing screws must be careful not to pinch your marimbas. ◆ Installation Location Use or storage in the following instructions...
... and make sure to keep the manual in other problems. Retighten the screws from time to vibrations. ◆ Handling • Never place an object on the YM-410/410F/460/460F should carry out this part of the legs the fixing screws must be careful not to pinch your marimbas. ◆ Installation Location Use or storage in the following instructions...
Owner's Manual
Page 4
... the YM-410/410F is adjustable in which offers a rich sound that have a unique semi-hollow design. Precise tuning of YAMAHA's concert marimbas. Locking screws fit into channels on tone quality and playability, has led to wood tone bars, Acoustalon is soft and deep. Type F models use of the harmonic overtones, which can be adjusted in 3-steps to avoid loss of these marimbas, using select...
... the YM-410/410F is adjustable in which offers a rich sound that have a unique semi-hollow design. Precise tuning of YAMAHA's concert marimbas. Locking screws fit into channels on tone quality and playability, has led to wood tone bars, Acoustalon is soft and deep. Type F models use of the harmonic overtones, which can be adjusted in 3-steps to avoid loss of these marimbas, using select...
Owner's Manual
Page 5
Accidental tone bars Rail Natural tone bars Suspension cord Frame end Leg (Small end) Slant shaft Resonators (Accidental tone side) ■ YM-410D Rail Reinforcement stay (Small end) Reinforcement stay (Large end) Caster Accidental tone bars Natural tone bars Suspension cord Leg (Small end) Reinforcement stay (Small end) Resonators (Accidental tone side) Slide leg Resonators (Natural tone side) Caster (with brake) Leg (Large end) Frame end Leg (Large end) Caster (with brake) Caster 25 NOMENCLATURE ■ YM-460/460F/410/410F/46/41 * The illustration shows model YM-460.
Accidental tone bars Rail Natural tone bars Suspension cord Frame end Leg (Small end) Slant shaft Resonators (Accidental tone side) ■ YM-410D Rail Reinforcement stay (Small end) Reinforcement stay (Large end) Caster Accidental tone bars Natural tone bars Suspension cord Leg (Small end) Reinforcement stay (Small end) Resonators (Accidental tone side) Slide leg Resonators (Natural tone side) Caster (with brake) Leg (Large end) Frame end Leg (Large end) Caster (with brake) Caster 25 NOMENCLATURE ■ YM-460/460F/410/410F/46/41 * The illustration shows model YM-460.
Owner's Manual
Page 6
... parts shown below. Before assembling the instrument, confirm that all parts are included as listed. * In the event that a part is missing, please contact the shop where the instrument was purchased. q Natural tone bars y Rail (1) YM-460/460F, 46: Two-section folding type YM-410/410F, 41: One-piece type w Accidental tone bars u Rail (2) YM-460/460F, 46: Two-section folding type YM-410/410F, 41: One-piece type...
... parts shown below. Before assembling the instrument, confirm that all parts are included as listed. * In the event that a part is missing, please contact the shop where the instrument was purchased. q Natural tone bars y Rail (1) YM-460/460F, 46: Two-section folding type YM-410/410F, 41: One-piece type w Accidental tone bars u Rail (2) YM-460/460F, 46: Two-section folding type YM-410/410F, 41: One-piece type...
Owner's Manual
Page 7
...Connect the large and the small end legs using the reinforcement stays. * YM-460/460F/410/410F: Before proceeding to assemble the instrument on a soft rug or carpet. YM-460/460F/410/410F/46/41 ASSEMBLY For safety, the instrument should be tightly seated in a location with sufficient space. Leg (Small end) Frame end (Large end) High sound... and small end legs are securely fastened. We recommend to you to the next step, make sure that they will be positioned as illustrated below after assembly. Place the large and small end legs and reinforcement stays so that the slide leg fixing...
...Connect the large and the small end legs using the reinforcement stays. * YM-460/460F/410/410F: Before proceeding to assemble the instrument on a soft rug or carpet. YM-460/460F/410/410F/46/41 ASSEMBLY For safety, the instrument should be tightly seated in a location with sufficient space. Leg (Small end) Frame end (Large end) High sound... and small end legs are securely fastened. We recommend to you to the next step, make sure that they will be positioned as illustrated below after assembly. Place the large and small end legs and reinforcement stays so that the slide leg fixing...
Owner's Manual
Page 8
YM-460/460F/46: Connect the reinforcement stays at the center. Insert the reinforcement stay with ...ASSEMBLY 1-2. In the same way, install the reinforcement stay to the hole for the screw as it will go (aligning the notch with its notch facing up into the lower joint of the fixing bolt and the holes in the reinforcement stays and tighten the fixing bolt securely. * Insert the support using... the reference hole close to the small end leg. (There is printed on the small end joint.) 28 Align the end of the large end leg as far as a guide.
YM-460/460F/46: Connect the reinforcement stays at the center. Insert the reinforcement stay with ...ASSEMBLY 1-2. In the same way, install the reinforcement stay to the hole for the screw as it will go (aligning the notch with its notch facing up into the lower joint of the fixing bolt and the holes in the reinforcement stays and tighten the fixing bolt securely. * Insert the support using... the reference hole close to the small end leg. (There is printed on the small end joint.) 28 Align the end of the large end leg as far as a guide.
Owner's Manual
Page 9
... can be adjusted at the center of the rail (3) with the shorter clamp should face the audience. (1) Tone bar posts High sound side # B " A Player side $ % C D Frame end Low sound side Audience side 2-2. Make sure that legs on the left and right sides are inserted fully and stop. Logo side facing..., but push both sides are vertical, use the screw to connect the end of the stay to the center of the instrument, and when the leg height is set low, use the outer hole and tighten the screw firmly. 2-3. YM-460/460F/410/410F/46/41 ASSEMBLY x Insert the rails (2) and (3) ...
... can be adjusted at the center of the rail (3) with the shorter clamp should face the audience. (1) Tone bar posts High sound side # B " A Player side $ % C D Frame end Low sound side Audience side 2-2. Make sure that legs on the left and right sides are inserted fully and stop. Logo side facing..., but push both sides are vertical, use the screw to connect the end of the stay to the center of the instrument, and when the leg height is set low, use the outer hole and tighten the screw firmly. 2-3. YM-460/460F/410/410F/46/41 ASSEMBLY x Insert the rails (2) and (3) ...
Owner's Manual
Page 10
...the bass side of the resonators into shorter grooves when the temperature is not available due to bump the resonators against the legs, etc. If desirable resonance is lower. Temperature Grooves to use ...factory adjusted so that the natural tone and accidental tone sides are properly assembled. Make sure that the optimum resonance level is higher and into the center grooves on the resonator holder. * Make sure not to confuse the natural tone resonators and accidental tone resonators. * Take care not to the temperature lower or higher than 23°C, adjust setting of the YM...
...the bass side of the resonators into shorter grooves when the temperature is not available due to bump the resonators against the legs, etc. If desirable resonance is lower. Temperature Grooves to use ...factory adjusted so that the natural tone and accidental tone sides are properly assembled. Make sure that the optimum resonance level is higher and into the center grooves on the resonator holder. * Make sure not to confuse the natural tone resonators and accidental tone resonators. * Take care not to the temperature lower or higher than 23°C, adjust setting of the YM...
Owner's Manual
Page 11
... every tone bar post, fix the tone bars by pulling the right and left cords forward from the large end side and hooking the two springs into the frame ends of the large end leg, and a mark "D" for the rail (4). b Set the tone bars. 5-1. While adjusting the ...tone bars, use care not to cause any damage to them. After confirming that the cord is printed on rail (2) and rail (3) with rail (1) and rail (4), respectively. Small end Large end Suspension cord Suspension cord Springs 31 Insert the outer rails (1) and (4) in the same way as the inner rails (2) and (3). YM-460/460F/410...
... every tone bar post, fix the tone bars by pulling the right and left cords forward from the large end side and hooking the two springs into the frame ends of the large end leg, and a mark "D" for the rail (4). b Set the tone bars. 5-1. While adjusting the ...tone bars, use care not to cause any damage to them. After confirming that the cord is printed on rail (2) and rail (3) with rail (1) and rail (4), respectively. Small end Large end Suspension cord Suspension cord Springs 31 Insert the outer rails (1) and (4) in the same way as the inner rails (2) and (3). YM-460/460F/410...
Owner's Manual
Page 12
... Do not touch the notched part during height adjustment to the rail section (2) so that the stays can be moved. When a slide leg fixing bolt is tightened in between two notches, there is very dangerous. Use the next channel above before adjusting the height. 32 Align notch with the floor. Always make sure the tone bars are held...
... Do not touch the notched part during height adjustment to the rail section (2) so that the stays can be moved. When a slide leg fixing bolt is tightened in between two notches, there is very dangerous. Use the next channel above before adjusting the height. 32 Align notch with the floor. Always make sure the tone bars are held...
Owner's Manual
Page 13
... assembling the instrument, confirm that all parts are included as listed. * In the event that a part is missing, please contact the shop where the instrument was purchased. q Natural tone bars y Rail (1) w Accidental tone bars e Resonators (Natural tone side) r Resonators (Accidental tone side) u Rail (2) Rail clamp i Rail (3) Threaded hole Clamp on both sides o Rail (4) YAMAHA logo !0 Leg (Large end) t Reinforcement stay For low sound...
... assembling the instrument, confirm that all parts are included as listed. * In the event that a part is missing, please contact the shop where the instrument was purchased. q Natural tone bars y Rail (1) w Accidental tone bars e Resonators (Natural tone side) r Resonators (Accidental tone side) u Rail (2) Rail clamp i Rail (3) Threaded hole Clamp on both sides o Rail (4) YAMAHA logo !0 Leg (Large end) t Reinforcement stay For low sound...
Owner's Manual
Page 14
...Low sound side 1-2. Place the large and small end legs and reinforcement stays so that they will be assembled by at the center. Align the end of the fixing bolt and the holes in a location with sufficient space. YM-410D ASSEMBLY For safety, the instrument should be positioned as a guide. z Connect the large and the small end legs using...the hole for the screw as illustrated below after assembly. Connect the reinforcement stays at least two persons in the reinforcement stays and tighten the fixing bolt securely. * Insert the support using the reinforcement stays. 1-1.
...Low sound side 1-2. Place the large and small end legs and reinforcement stays so that they will be assembled by at the center. Align the end of the fixing bolt and the holes in a location with sufficient space. YM-410D ASSEMBLY For safety, the instrument should be positioned as a guide. z Connect the large and the small end legs using...the hole for the screw as illustrated below after assembly. Connect the reinforcement stays at least two persons in the reinforcement stays and tighten the fixing bolt securely. * Insert the support using the reinforcement stays. 1-1.
Owner's Manual
Page 15
1-3 Insert the reinforcement stay with its notch facing up into the stay mount hole of the large end leg as far as it will go (aligning the notch with the fixing bolt) and tighten the fixing bolt securely. In the same way, install the reinforcement stay to the small end leg. (There is no marking on the small end joint.) Stay mount 35 YM-410D ASSEMBLY Fixing bolt Leg E E Reinforcement stay Notch Fixing bolt Leg (Large end) Tighten Notch Reinforcement stay 1-4.
1-3 Insert the reinforcement stay with its notch facing up into the stay mount hole of the large end leg as far as it will go (aligning the notch with the fixing bolt) and tighten the fixing bolt securely. In the same way, install the reinforcement stay to the small end leg. (There is no marking on the small end joint.) Stay mount 35 YM-410D ASSEMBLY Fixing bolt Leg E E Reinforcement stay Notch Fixing bolt Leg (Large end) Tighten Notch Reinforcement stay 1-4.
Owner's Manual
Page 16
... YM-410D ASSEMBLY x Insert the rails (2), (3) and (4) into grooves alternately little by little until both sides are vertical, use the screw to the hole for attaching the stay. Make sure that legs on the bass side. After confirming that the end of the rail with the shorter clamp should face the audience. (1) Tone bar posts High sound...
... YM-410D ASSEMBLY x Insert the rails (2), (3) and (4) into grooves alternately little by little until both sides are vertical, use the screw to the hole for attaching the stay. Make sure that legs on the bass side. After confirming that the end of the rail with the shorter clamp should face the audience. (1) Tone bar posts High sound...
Owner's Manual
Page 17
... ("A" in the rubber resonator holder. Make sure that the pipes are factory adjusted so that the optimum resonance level is not available due to fit into longer grooves when the temperature is lower. YM-410D ASSEMBLY c Attach the resonators. 3-1. Resonators (Natural tone side) Resonators (Accidental tone side) * The resonators are set the natural tone resonator pipes in the figure...
... ("A" in the rubber resonator holder. Make sure that the pipes are factory adjusted so that the optimum resonance level is not available due to fit into longer grooves when the temperature is lower. YM-410D ASSEMBLY c Attach the resonators. 3-1. Resonators (Natural tone side) Resonators (Accidental tone side) * The resonators are set the natural tone resonator pipes in the figure...
Owner's Manual
Page 18
... adjusting the long frame, engage the rail clamp on the large end face of the rail (1) and the groove section of the frame end of the legs. 4-1. Small end Large end Suspension cord Suspension cord ...as the inner rails (2), (3) and (4). YM-410D ASSEMBLY v Insert the rail (1) into each tone bar individually and hook its DPSEonto the corresponding tone bar post. Set the natural tone bars first. 8JUIPOFQFSTPOIPMEJOHUIF...SBJMT Align each other. * When setting the tone bars, use care not to cause any damage to every post, fix the tone bars by pulling the right and left DPSEs...
... adjusting the long frame, engage the rail clamp on the large end face of the rail (1) and the groove section of the frame end of the legs. 4-1. Small end Large end Suspension cord Suspension cord ...as the inner rails (2), (3) and (4). YM-410D ASSEMBLY v Insert the rail (1) into each tone bar individually and hook its DPSEonto the corresponding tone bar post. Set the natural tone bars first. 8JUIPOFQFSTPOIPMEJOHUIF...SBJMT Align each other. * When setting the tone bars, use care not to cause any damage to every post, fix the tone bars by pulling the right and left DPSEs...
Owner's Manual
Page 19
...: Steel Pipe with Adjustable Height) ● Dimensions (W x D x H): YM-410D: 183 x 83 x 88 cm (72" x 32.7" x 34.6" ) YM-410/410F: 183 x 83 x 76 - 88 cm (72" x 32.7" x 29.9 - 34.6" ) ● Weight: YM-410D/410F: 55 kg (121 lbs 4 oz) YM-410: 49 kg (108 lbs) ● Casters: 100mm Diameter Casters ■ YM-46/41 ● Range: YM-46: A25 - SPECIFICATIONS/SCALE RANGE ■...
...: Steel Pipe with Adjustable Height) ● Dimensions (W x D x H): YM-410D: 183 x 83 x 88 cm (72" x 32.7" x 34.6" ) YM-410/410F: 183 x 83 x 76 - 88 cm (72" x 32.7" x 29.9 - 34.6" ) ● Weight: YM-410D/410F: 55 kg (121 lbs 4 oz) YM-410: 49 kg (108 lbs) ● Casters: 100mm Diameter Casters ■ YM-46/41 ● Range: YM-46: A25 - SPECIFICATIONS/SCALE RANGE ■...