Owner's Manual
Page 2
...Rear panel 3 SPEAKERS (speaker output) jacks These jacks are Speakon-type connectors. Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Note: The SPEAKERS 1 & 2 jacks (rear panel 3) output the signals received at the ` ST OUT jack (...the LIMITER indicator (X). If the output level is +4dB (Level Meter "0"), the internal power amplifier will deliver 100W into 4Ω. 1 EMX5000-20/EMX5000-12 Check the output signal level via the internal power amplifier. A- 1+ 2+ B+ 2- BRIDGE 1+ + 1- 2+ - 2- The setting ...
...Rear panel 3 SPEAKERS (speaker output) jacks These jacks are Speakon-type connectors. Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Note: The SPEAKERS 1 & 2 jacks (rear panel 3) output the signals received at the ` ST OUT jack (...the LIMITER indicator (X). If the output level is +4dB (Level Meter "0"), the internal power amplifier will deliver 100W into 4Ω. 1 EMX5000-20/EMX5000-12 Check the output signal level via the internal power amplifier. A- 1+ 2+ B+ 2- BRIDGE 1+ + 1- 2+ - 2- The setting ...
Owner's Manual
Page 7
... of the two effect units) include TAP DELAY, which is very useful for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Contents Introduction 5 Features 5 EMX5000-20/EMX5000-12 Quick Guide 6 Front and rear panel 10 Control panel 10 Input/output panel 16 Rear.... The sixteen types (provided by adding a power amplifier or powered speakers. • The EMX5000-20/EMX5000-12 also has a PHONES jack, which lets you easily adjust the delay time. • The EMX5000-20/EMX5000-12 has implemented "EEEngine", Yamaha's epochal amp drive technology to smallscale PA systems...
... of the two effect units) include TAP DELAY, which is very useful for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Contents Introduction 5 Features 5 EMX5000-20/EMX5000-12 Quick Guide 6 Front and rear panel 10 Control panel 10 Input/output panel 16 Rear.... The sixteen types (provided by adding a power amplifier or powered speakers. • The EMX5000-20/EMX5000-12 also has a PHONES jack, which lets you easily adjust the delay time. • The EMX5000-20/EMX5000-12 has implemented "EEEngine", Yamaha's epochal amp drive technology to smallscale PA systems...
Owner's Manual
Page 19
... built-in the upper part of the control panel will light. 4 LINE (stereo) input jacks EMX5000-20: 17/18-19/20, EMX5000-12: 9/10-11/12 These are the input jacks for the phantom power supplied to the INPUT A jacks of each channel will be sent to switch the built-in digital...2 ON/OFF jack A separately sold Yamaha FC5 foot switch can connect either phone plugs or RCA phono plugs, as a cassette deck, to connect stereo outputs of the signal output from these jacks is 3mW when headphones are phono jacks that allow the signal from the mixer section. EMX5000-20/EMX5000-12-Owner's Manual
... built-in the upper part of the control panel will light. 4 LINE (stereo) input jacks EMX5000-20: 17/18-19/20, EMX5000-12: 9/10-11/12 These are the input jacks for the phantom power supplied to the INPUT A jacks of each channel will be sent to switch the built-in digital...2 ON/OFF jack A separately sold Yamaha FC5 foot switch can connect either phone plugs or RCA phono plugs, as a cassette deck, to connect stereo outputs of the signal output from these jacks is 3mW when headphones are phono jacks that allow the signal from the mixer section. EMX5000-20/EMX5000-12-Owner's Manual
Owner's Manual
Page 31
...Powered Mixer Q&A Q: The built-in the STEREO SUB INPUT section may be turned on connections (page 19-20) and change the connections so that the impedance is dark. If the load impedance (including a short) is too low, refer to the peak level indicators of the cient load impedance of 4-8 ohms. EMX5000-20/EMX5000...-12-Owner's Manual When the device cools off , normal operation too great, and the protection circuit for the exces- Problem Cause Action The POWER indicator is correct. Sound is not ventilated ...
...Powered Mixer Q&A Q: The built-in the STEREO SUB INPUT section may be turned on connections (page 19-20) and change the connections so that the impedance is dark. If the load impedance (including a short) is too low, refer to the peak level indicators of the cient load impedance of 4-8 ohms. EMX5000-20/EMX5000...-12-Owner's Manual When the device cools off , normal operation too great, and the protection circuit for the exces- Problem Cause Action The POWER indicator is correct. Sound is not ventilated ...
Owner's Manual
Page 33
Balanced. (T=HOT, R=COLD, S=GND) 3. before clip mixer CH INPUT A -60 (CH1-8/1-16) -16 CH INPUT B -60 (CH1-8/1-16) -16 ST INPUT -34 (CH9-12/17-20) +10 ST SUB IN (1, 2) 2TR IN (L, R) INSERT IN (CH1-8/1-16) POWER AMP IN (A, B) 5 kΩ 50 kΩ 10 kΩ -... 538 mm (EMX5000-20) / 478 × 158 × 538 mm (EMX5000-12) 19 kg (EMX5000-20) / 15 kg (EMX5000-12) Power cord, Owner's Manual s Input specifications Input terminals Gain control Actual load impedance For use with nominal Sensitivity1 Input level Nominal Connectors on mixer Nominal Max. before...
Balanced. (T=HOT, R=COLD, S=GND) 3. before clip mixer CH INPUT A -60 (CH1-8/1-16) -16 CH INPUT B -60 (CH1-8/1-16) -16 ST INPUT -34 (CH9-12/17-20) +10 ST SUB IN (1, 2) 2TR IN (L, R) INSERT IN (CH1-8/1-16) POWER AMP IN (A, B) 5 kΩ 50 kΩ 10 kΩ -... 538 mm (EMX5000-20) / 478 × 158 × 538 mm (EMX5000-12) 19 kg (EMX5000-20) / 15 kg (EMX5000-12) Power cord, Owner's Manual s Input specifications Input terminals Gain control Actual load impedance For use with nominal Sensitivity1 Input level Nominal Connectors on mixer Nominal Max. before...