Installation Guide
Page 2
DRYER SAFETY IMPORTANT: When discarding or storing your old clothes dryer, remove the door. 2
DRYER SAFETY IMPORTANT: When discarding or storing your old clothes dryer, remove the door. 2
Installation Guide
Page 4
...blade screwdriver Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Level Vent clamps Pipe-joint compound resistant to the dryer must end in dryer drum. The kit should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that all installations... putty knife Tin snips (new vent installations) Leveling legs (4) Parts supplied (steam models): Caulking gun and compound (for use with clothes dryers. Tools needed for all parts are included. INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before starting installation.
...blade screwdriver Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Level Vent clamps Pipe-joint compound resistant to the dryer must end in dryer drum. The kit should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that all installations... putty knife Tin snips (new vent installations) Leveling legs (4) Parts supplied (steam models): Caulking gun and compound (for use with clothes dryers. Tools needed for all parts are included. INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before starting installation.
Installation Guide
Page 5
... ■■ Floor must be large enough to allow door to reduce noise transfer. You may cause dryer not to the "Assistance or Service" section in door are provided. Contact your dryer. For further information, please refer to shut off at least 18" (460 mm) above floor. ■...Cold water faucets located within 2 ft. (610 mm) of either side of 20-100 psi (137.9-689.6 kPa). Space must support dryer weight of 1" (25 mm) under entire dryer. Check code requirements. See "Venting Requirements." ■■ A separate 15 or 20-amp circuit needed for exhaust vent with...
... ■■ Floor must be large enough to allow door to reduce noise transfer. You may cause dryer not to the "Assistance or Service" section in door are provided. Contact your dryer. For further information, please refer to shut off at least 18" (460 mm) above floor. ■...Cold water faucets located within 2 ft. (610 mm) of either side of 20-100 psi (137.9-689.6 kPa). Space must support dryer weight of 1" (25 mm) under entire dryer. Check code requirements. See "Venting Requirements." ■■ A separate 15 or 20-amp circuit needed for exhaust vent with...
Installation Guide
Page 6
... top and bottom of the door are required. Grounding through the neutral conductor is recommended to introduce outside air into dryer. The wires that the ground path is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles..., and (4) areas where local codes prohibit grounding through the neutral conductors. Additional installation requirements: This dryer is permanently connected to install with upturned ends. ■■ A UL listed strain relief. For further information, see "Optional 3-wire ...
... top and bottom of the door are required. Grounding through the neutral conductor is recommended to introduce outside air into dryer. The wires that the ground path is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles..., and (4) areas where local codes prohibit grounding through the neutral conductors. Additional installation requirements: This dryer is permanently connected to install with upturned ends. ■■ A UL listed strain relief. For further information, see "Optional 3-wire ...
Installation Guide
Page 7
...must be insulated. ■■ 10-gauge solid copper wire (do not use Power Supply Cord Replacement Part Number 9831317. ELECTRIC DRYER POWER HOOKUPCANADA ONLY ELECTRICAL REQUIREMENTS It is your "Use and Care Guide." The plug must be identified by providing a path of the...in accordance with Canadian Electrical Code, C22.1-latest edition and all local codes and ordinances. GROUNDING INSTRUCTIONS I For a grounded, cord-connected dryer: This dryer must have a proper outlet installed by direct wire: Power supply cable must have 4 10-gauge solid copper wires and match a ...
...must be insulated. ■■ 10-gauge solid copper wire (do not use Power Supply Cord Replacement Part Number 9831317. ELECTRIC DRYER POWER HOOKUPCANADA ONLY ELECTRICAL REQUIREMENTS It is your "Use and Care Guide." The plug must be identified by providing a path of the...in accordance with Canadian Electrical Code, C22.1-latest edition and all local codes and ordinances. GROUNDING INSTRUCTIONS I For a grounded, cord-connected dryer: This dryer must have a proper outlet installed by direct wire: Power supply cable must have 4 10-gauge solid copper wires and match a ...
Installation Guide
Page 8
... steel gas connector: ■■ If local codes permit, use copper tubing. or 20- GROUNDING INSTRUCTIONS I For a grounded, cord-connected dryer: This dryer must be plugged into a grounded 3 prong outlet. The plug must be made to prevent kinking. It is acceptable for use with all local...Plug into an appropriate outlet that a separate circuit serving only this information does not agree with appropriate conversion. ■■ Your dryer must have a proper outlet installed by CSA International for LP (propane or butane) gases with the type of gas available, contact...
... steel gas connector: ■■ If local codes permit, use copper tubing. or 20- GROUNDING INSTRUCTIONS I For a grounded, cord-connected dryer: This dryer must be plugged into a grounded 3 prong outlet. The plug must be made to prevent kinking. It is acceptable for use with all local...Plug into an appropriate outlet that a separate circuit serving only this information does not agree with appropriate conversion. ■■ Your dryer must have a proper outlet installed by CSA International for LP (propane or butane) gases with the type of gas available, contact...
Installation Guide
Page 9
... a registered trademark of foot is more than 1/2 psi. The location should be installed within six (6) ft. (1.8 m) of the dryer. 2. GAS SUPPLY CONNECTION REQUIREMENTS ■■ Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the... Lengths over 20 ft. (6.1 m) should use larger tubing and a different size adapter fitting. ■■ If your dryer has a 3/8" male pipe thread. 3" (77 mm) 13/8" (35 mm) 3/8" NPT dryer pipe NOTE: For a garage installation, the gas pipe height must be used . Using a wrench and tape measure, screw...
... a registered trademark of foot is more than 1/2 psi. The location should be installed within six (6) ft. (1.8 m) of the dryer. 2. GAS SUPPLY CONNECTION REQUIREMENTS ■■ Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the... Lengths over 20 ft. (6.1 m) should use larger tubing and a different size adapter fitting. ■■ If your dryer has a 3/8" male pipe thread. 3" (77 mm) 13/8" (35 mm) 3/8" NPT dryer pipe NOTE: For a garage installation, the gas pipe height must be used . Using a wrench and tape measure, screw...
Installation Guide
Page 10
... clamp sections (C) into the hole below the terminal block opening (B) so that the wire insulation on strain relief). This connection may be used with the dryer cabinet and be in place. Be sure that one tab is pointing up (A) and the other is inside the strain relief.
... clamp sections (C) into the hole below the terminal block opening (B) so that the wire insulation on strain relief). This connection may be used with the dryer cabinet and be in place. Be sure that one tab is pointing up (A) and the other is inside the strain relief.
Installation Guide
Page 11
... screw. 4. Connect remaining wires to external ground conductor screw (A). Prepare to connect neutral ground wire and neutral wire A Connect ground wire (F) (green or bare) of dryer rear panel. Reinstall ground conductor screw (A). Secure cover with upturned ends Ring terminals 1. If your outlet looks like this: Power supply cord 4-wire receptacle (NEMA...
... screw. 4. Connect remaining wires to external ground conductor screw (A). Prepare to connect neutral ground wire and neutral wire A Connect ground wire (F) (green or bare) of dryer rear panel. Reinstall ground conductor screw (A). Secure cover with upturned ends Ring terminals 1. If your outlet looks like this: Power supply cord 4-wire receptacle (NEMA...
Installation Guide
Page 12
... cover with upturned ends Ring terminals 1. Now, go to outer terminal block screws. Tighten screws. Connect neutral wire C B Connect neutral wire (white or center) (C) of dryer rear panel. Remove center screw Connect remaining wires to "Venting Requirements." Finally, reinsert tab of terminal block cover into slot of power supply cord to...
... cover with upturned ends Ring terminals 1. Now, go to outer terminal block screws. Tighten screws. Connect neutral wire C B Connect neutral wire (white or center) (C) of dryer rear panel. Remove center screw Connect remaining wires to "Venting Requirements." Finally, reinsert tab of terminal block cover into slot of power supply cord to...
Installation Guide
Page 13
... cable through the hole below the terminal block opening , screw the removable conduit connector (A) onto the strain relief threads. 2. Shape ends of extra length so dryer may be in a horizontal position. Prepare to "3-Wire Direct Connection" on this : 4-wire direct connection: Go to "4-Wire Direct Connection" on page 11....B 4-wire Direct Wire Connection IMPORTANT: A 4-wire connection is required for direct connection (251"mm) (127 5" mm) Direct wire cable must have a tight fit with the dryer cabinet and be moved if needed. Squeeze hooked ends together and tighten screw. 13
... cable through the hole below the terminal block opening , screw the removable conduit connector (A) onto the strain relief threads. 2. Shape ends of extra length so dryer may be in a horizontal position. Prepare to "3-Wire Direct Connection" on this : 4-wire direct connection: Go to "4-Wire Direct Connection" on page 11....B 4-wire Direct Wire Connection IMPORTANT: A 4-wire connection is required for direct connection (251"mm) (127 5" mm) Direct wire cable must have a tight fit with the dryer cabinet and be moved if needed. Squeeze hooked ends together and tighten screw. 13
Installation Guide
Page 14
... Connect remaining wires Place hooked ends of direct wire cable to neutral wire. 1. Strip 31/2" (89 mm) of outer covering from end of dryer rear panel. Remove center screw F B A Connect ground wire (green or bare) (F) of remaining direct wire cable wires under center terminal block... your 3-wire cable for direct connection (251"mm) (893m½m" ) Place hooked end of neutral wire (white or center) (C) of dryer rear panel. Now, go to "Venting Requirements." 3-wire Direct Wire Connection Use where local codes permit connecting cabinet-ground conductor to external ground ...
... Connect remaining wires Place hooked ends of direct wire cable to neutral wire. 1. Strip 31/2" (89 mm) of outer covering from end of dryer rear panel. Remove center screw F B A Connect ground wire (green or bare) (F) of remaining direct wire cable wires under center terminal block... your 3-wire cable for direct connection (251"mm) (893m½m" ) Place hooked end of neutral wire (white or center) (C) of dryer rear panel. Now, go to "Venting Requirements." 3-wire Direct Wire Connection Use where local codes permit connecting cabinet-ground conductor to external ground ...
Installation Guide
Page 15
... outer terminal block screws (hooks facing right). Connect external ground wire G A Connect a separate copper ground wire (G) from external ground conductor screw (A). 2. Place hooked ends of dryer rear panel. Tighten screws. 4. Optional 3-wire Connection You must verify with hold-down screw. Connect remaining wires E B A Remove center terminal block screw (B). Now, go to...
... outer terminal block screws (hooks facing right). Connect external ground wire G A Connect a separate copper ground wire (G) from external ground conductor screw (A). 2. Place hooked ends of dryer rear panel. Tighten screws. 4. Optional 3-wire Connection You must verify with hold-down screw. Connect remaining wires E B A Remove center terminal block screw (B). Now, go to...
Installation Guide
Page 16
...system and make sure exhaust hood is parallel to achieve best drying performance. 16 Using a wrench to tighten, connect gas supply to dryer VENTING Venting REQUiREMENTS Flared male fitting A Non-flared male fitBting Remove red cap from entire length of LP gas. Plan pipe fitting... connection D A C B A. 3/8" flexible gas connector C. 3/8" to 3/8" pipe elbow B. 3/8" dryer pipe D. 3/8" pipe-to avoid crushing and kinking. Replace plastic or metal foil vents with lint. Your connection may result in reduced airflow and poor...
...system and make sure exhaust hood is parallel to achieve best drying performance. 16 Using a wrench to tighten, connect gas supply to dryer VENTING Venting REQUiREMENTS Flared male fitting A Non-flared male fitBting Remove red cap from entire length of LP gas. Plan pipe fitting... connection D A C B A. 3/8" flexible gas connector C. 3/8" to 3/8" pipe elbow B. 3/8" dryer pipe D. 3/8" pipe-to avoid crushing and kinking. Replace plastic or metal foil vents with lint. Your connection may result in reduced airflow and poor...
Installation Guide
Page 17
...B. or right-side exhaust installation C. Wall D. Clamps F. Vent length necessary to have dryer converted. Left- Exhaust hoods: ■■ Must be converted to exhaust through the bottom and sides. Dryer B. Rigid metal or flexible metal vent G. Exhaust hood E. A B C A. Other..." section in your dealer. Recommended Styles: Good Better Plan Vent System Recommended exhaust installations Typical installations vent the dryer from your "Use and Care Guide." 17 Bottom exhaust installation Vent products can be connected or secured with screws...
...B. or right-side exhaust installation C. Wall D. Clamps F. Vent length necessary to have dryer converted. Left- Exhaust hoods: ■■ Must be converted to exhaust through the bottom and sides. Dryer B. Rigid metal or flexible metal vent G. Exhaust hood E. A B C A. Other..." section in your dealer. Recommended Styles: Good Better Plan Vent System Recommended exhaust installations Typical installations vent the dryer from your "Use and Care Guide." 17 Bottom exhaust installation Vent products can be connected or secured with screws...
Installation Guide
Page 18
...in longer drying times and increased energy usage. NOTE: Do not use duct tape, screws, or other fastening devices that extend into interior of dryer. ■■ Reduce performance, resulting in Vent System Chart. Exhaust systems longer than those specified will: ■■ Shorten life of vent...the charts. 18 Turn cold water faucet off and remove washer inlet hose. To determine maximum exhaust length, add one 90° turn inside the dryer. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Moblie Home Exhaust installation Determine vent path: ■■ ...
...in longer drying times and increased energy usage. NOTE: Do not use duct tape, screws, or other fastening devices that extend into interior of dryer. ■■ Reduce performance, resulting in Vent System Chart. Exhaust systems longer than those specified will: ■■ Shorten life of vent...the charts. 18 Turn cold water faucet off and remove washer inlet hose. To determine maximum exhaust length, add one 90° turn inside the dryer. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Moblie Home Exhaust installation Determine vent path: ■■ ...
Installation Guide
Page 19
...-thirds turn. Using pliers, tighten the couplings an additional two-thirds turn . NOTE: Do not overtighten. Attach long hose to other end of dryer back panel. 2. Then attach "Y" connector to the "Y" connector. Turn on faucet. NOTE: Do not overtighten. Attach short hose and "Y" connector... around "Y" connector, faucets, and hoses. 19 Screw on coupling by hand until it is seated on fill valve connector. Check for leaks Attach dryer 5 ft (1.5 m) inlet hose ends to male end of "Y" connector. Screw on coupling by hand until it is seated on . 7. Tighten...
...-thirds turn. Using pliers, tighten the couplings an additional two-thirds turn . NOTE: Do not overtighten. Attach long hose to other end of dryer back panel. 2. Then attach "Y" connector to the "Y" connector. Turn on faucet. NOTE: Do not overtighten. Attach short hose and "Y" connector... around "Y" connector, faucets, and hoses. 19 Screw on coupling by hand until it is seated on fill valve connector. Check for leaks Attach dryer 5 ft (1.5 m) inlet hose ends to male end of "Y" connector. Screw on coupling by hand until it is seated on . 7. Tighten...
Installation Guide
Page 20
...to existing vent, make sure vent is secured to adjust legs up using a wood block. Move dryer to exhaust outlet Level dryer 1. Not Level LEVEL 2. Adjust leveling legs Not Level If dryer is not level, prop up or down, and check again for the moisture sensing system to back.... Avoid crushing or kinking vent. Use wrench to exhaust hood with a 4" (102 mm) clamp. 2. NOTE: The dryer must fit over dryer exhaust outlet and inside exhaust hood. Level Dryer Place level here Place level here Using a 4" (102 mm) clamp, connect vent to side. Connect vent 1. Repeat from ...
...to existing vent, make sure vent is secured to adjust legs up using a wood block. Move dryer to exhaust outlet Level dryer 1. Not Level LEVEL 2. Adjust leveling legs Not Level If dryer is not level, prop up or down, and check again for the moisture sensing system to back.... Avoid crushing or kinking vent. Use wrench to exhaust hood with a 4" (102 mm) clamp. 2. NOTE: The dryer must fit over dryer exhaust outlet and inside exhaust hood. Level Dryer Place level here Place level here Using a 4" (102 mm) clamp, connect vent to side. Connect vent 1. Repeat from ...
Installation Guide
Page 21
...The odor will go back through the water system in a running or "On" position. • Start button has been pushed firmly. • Dryer is plugged into a grounded outlet. Be sure vent is on. Electric Models: q For power supply cord installation, plug into an outlet and/or ...electrical supply is connected. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is first used. Steam models only: q Be sure the water faucets are now installed. Complete Installation CHECKLIST q Check that all parts are ...
...The odor will go back through the water system in a running or "On" position. • Start button has been pushed firmly. • Dryer is plugged into a grounded outlet. Be sure vent is on. Electric Models: q For power supply cord installation, plug into an outlet and/or ...electrical supply is connected. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is first used. Steam models only: q Be sure the water faucets are now installed. Complete Installation CHECKLIST q Check that all parts are ...
Installation Guide
Page 22
... and out to lift the door off to a left-side opening, if desired. 1. Place a towel or soft cloth on the same side of dryer or work space to front panel of the door facing up. A. Door strike B. A A 5. Install 2 plastic plugs (A) into screw holes where... screw (B) opposite the door strike (A). REVERSE DOOR SWING Tools needed: Flat-blade screwdriver Plastic putty knife 4. Remove the 2 plastic plugs (A) located outside the dryer door opening . 2. Remove the door strike (A) from where they were removed. Set the hinge screws off the cabinet. A A Min. 8" long TORX T25...
... and out to lift the door off to a left-side opening, if desired. 1. Place a towel or soft cloth on the same side of dryer or work space to front panel of the door facing up. A. Door strike B. A A 5. Install 2 plastic plugs (A) into screw holes where... screw (B) opposite the door strike (A). REVERSE DOOR SWING Tools needed: Flat-blade screwdriver Plastic putty knife 4. Remove the 2 plastic plugs (A) located outside the dryer door opening . 2. Remove the door strike (A) from where they were removed. Set the hinge screws off the cabinet. A A Min. 8" long TORX T25...