Owners Manual
Page 5
... WARNING Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Items containing foam, rubber, or plastic must not exceed 3 feet. Do not dry anything that has ever had anything that has ever had any ...Do not dry anything flammable on it (including cooking oils). Failure to follow these instructions can result in death, explosion, or fire. Fire Hazard No washer can result in death or fire. 5 Failure to follow these instructions can completely remove oil. In the State of Massachusetts, the following installation instructions apply...
... WARNING Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Items containing foam, rubber, or plastic must not exceed 3 feet. Do not dry anything that has ever had anything that has ever had any ...Do not dry anything flammable on it (including cooking oils). Failure to follow these instructions can result in death, explosion, or fire. Fire Hazard No washer can result in death or fire. 5 Failure to follow these instructions can completely remove oil. In the State of Massachusetts, the following installation instructions apply...
Installation Instructions
Page 2
...dryer. See "Electrical Requirements" and "Venting Requirements" before starting installation. Mobile home installations require metal exhaust system hardware available for installing new exhaust vent) ■ Tin snips (new vent installations) ■ ¼" nut driver (recommended) ■ Tape measure ■ Pliers Parts supplied Non-Steam Models Steam... electrical supply and venting. Short inlet hose D. Inlet hose with any tools listed here. ■ Flat-blade screwdriver ■ #2 Phillips screwdriver ■ Adjustable wrench that all parts are included. Rubber washer ...
...dryer. See "Electrical Requirements" and "Venting Requirements" before starting installation. Mobile home installations require metal exhaust system hardware available for installing new exhaust vent) ■ Tin snips (new vent installations) ■ ¼" nut driver (recommended) ■ Tape measure ■ Pliers Parts supplied Non-Steam Models Steam... electrical supply and venting. Short inlet hose D. Inlet hose with any tools listed here. ■ Flat-blade screwdriver ■ #2 Phillips screwdriver ■ Adjustable wrench that all parts are included. Rubber washer ...
Installation Instructions
Page 3
...will need ■ A location that allows for your dryer. Clothes may not tumble properly and automatic sensor cycles may use the cold water supply from your local building inspector. Contact your washer using the "Y" connector provided. Installation clearances The location must... dryer. At lower temperatures, the dryer might not shut off at temperatures below 45ºF (7ºC). Check code requirements. Steam (Electric or Gas) A 38" (965 mm) B 32 9/16" (827 mm) C 27" (686 mm) D 52 9/16" (1335 mm) Non-Steam (Electric or Gas) 38" (965 mm) 31 1/2" (800 mm) 27"...
...will need ■ A location that allows for your dryer. Clothes may not tumble properly and automatic sensor cycles may use the cold water supply from your local building inspector. Contact your washer using the "Y" connector provided. Installation clearances The location must... dryer. At lower temperatures, the dryer might not shut off at temperatures below 45ºF (7ºC). Check code requirements. Steam (Electric or Gas) A 38" (965 mm) B 32 9/16" (827 mm) C 27" (686 mm) D 52 9/16" (1335 mm) Non-Steam (Electric or Gas) 38" (965 mm) 31 1/2" (800 mm) 27"...
Installation Instructions
Page 5
...Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH. Recommended installation spacing for recessed or closet installation, with stacked washer and dryer The dimensions shown are for the recommended spacing. 48 in.2 * (310 cm2) 3"* (76 mm) 24 in remodeling ... and all local codes and ordinances. The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in .2 * (155 cm2) 3"* (76 mm) 1"* (25 mm) A* 1" 27" 1" (25 mm) (686 mm) (25 mm) Steam (Electric or Gas) Non-Steam (Electric or Gas) A 5 ½" (140 mm...
...Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH. Recommended installation spacing for recessed or closet installation, with stacked washer and dryer The dimensions shown are for the recommended spacing. 48 in.2 * (310 cm2) 3"* (76 mm) 24 in remodeling ... and all local codes and ordinances. The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in .2 * (155 cm2) 3"* (76 mm) 1"* (25 mm) A* 1" 27" 1" (25 mm) (686 mm) (25 mm) Steam (Electric or Gas) Non-Steam (Electric or Gas) A 5 ½" (140 mm...
Installation Instructions
Page 14
...that the water faucets are on faucet. 10. A. CONNECT INLET HOSE (STEAM MODELS) The dryer must be attached directly to cold water faucet, go to other end of the dryer (not the console panel). Gently lay the dryer on connector. 6. Use a wrench to exhaust hood with Step 3. ...connector. NOTE: If "Y" connector can result. 9. NOTE: Do not overtighten. Using pliers, tighten the couplings with new rubber washer provided. See illustration. 4. Slide the dryer on the corner posts until it is seated on the cardboard. Attach "Y" connector to the cold water faucet, the short ...
...that the water faucets are on faucet. 10. A. CONNECT INLET HOSE (STEAM MODELS) The dryer must be attached directly to cold water faucet, go to other end of the dryer (not the console panel). Gently lay the dryer on connector. 6. Use a wrench to exhaust hood with Step 3. ...connector. NOTE: If "Y" connector can result. 9. NOTE: Do not overtighten. Using pliers, tighten the couplings with new rubber washer provided. See illustration. 4. Slide the dryer on the corner posts until it is seated on the cardboard. Attach "Y" connector to the cold water faucet, the short ...