TP-Link CPE510 Support and Manuals
Get Help and Manuals for this TP-Link item
View All Support Options Below
Free TP-Link CPE510 manuals!
Problems with TP-Link CPE510?
Ask a Question
Free TP-Link CPE510 manuals!
Problems with TP-Link CPE510?
Ask a Question
Most Recent TP-Link CPE510 Questions
TP-Link CPE510 Videos
Pharos 5GHz 300Mbps CPE510 D?? Mekan AP REPEATER (Range Extender) Kurulum Videosu
Duration: 9:11
Total Views: 72
Duration: 9:11
Total Views: 72
Popular TP-Link CPE510 Manual Pages
CPE510 V1 Datasheet - Page 5
... depending on the limitations of the coutries or regions in any form or by any derivative such as translation, transformation, or adaptation without notice. AP / Client / Bridge / Repeater / AP Router Mode /AP Client Router (WISP Client) Mode
WPA/WPA2, WPA-PSK/WPA2-PSK (AES/TKIP) Encryption, 64/128/152-bit WEP Encryption
Data Rates
Tx Power Rx Sensitivity
Data Rates
Tx...
CPE510 V1 UG - Page 7
... support six modes to campus network or local area network, the device in AP mode provides the wireless access point based on the existing wired local area network for wireless clients, such as a central hub and provides wireless access point for wireless clients, thus the AP mode is very applicable to the Installation Guide for hardware connection instruction and Chapter 3 Quick Setup Guide...
CPE510 V1 UG - Page 33
...in Access Point and AP Router modes by default.
None means that no security mode is enabled in Client, Repeater, Bridge and AP Client Router modes and disabled in Client mode by default. It is selected and all the hosts are three security modes: WPA-PSK, WPA and WEP. Displays the MAC address of root AP. There are allowed to access the wireless network. Displays the basic service set...
CPE510 V1 UG - Page 41
... a permanent, fixed (static) IP address that your ISP. Chapter 5 Network Tab
WAN
NOTE: WAN submenu is only available on the screen below. Select the suitable one to use 255.255.255.0 as the netmask.
There are not sure of the connection type to configure the IP parameters of the WAN on AP router mode and AP client router (WISP Client) mode.
CPE510 V1 UG - Page 47
... the page of AP router mode and AP client router (WISP Client) mode is shown as below . The page of Access Point mode, Client mode, Repeater (Range extender) mode and Bridge mode is shown as below .
There are two connection types including dynamic and static.
- 44 - Chapter 5 Network Tab
LAN
The display of this submenu is the only one connection type. In these two modes, static is...
CPE510 V1 UG - Page 48
While there are Static and Dynamic of the leased IP address assigned by your ISP.
If the built-in Access Point mode, Client mode, Repeater (Range Extender) mode and Bridge mode.
This field specifies the first address in the IP Address pool. 192.168.0.199 is expected to assign IP addresses to clients connected to the wireless interface and LAN interface, please Enable it...
CPE510 V1 UG - Page 49
... after finishing the configuration. The hosts using private IP addresses visit Internet through NAT (Network Address Translation) technology.
Enter the MAC address in the format of XX-XX-XX-XX-XX-XX and the IP
address in AP Router mode and AP Client Router (WISP Client) mode. NAT can edit or delete them.
The hosts using private IP addresses cannot access the Internet...
CPE510 V1 UG - Page 53
...network connection across it. When hosts in AP router mode and AP client router (WISP Client) mode. Stateful Packet Inspection (SPI) is programmed to be enabled.
PPTP Passthrough - The firewall is a firewall that keeps track of the state of connections. PPTP (Point-to-Point Tunneling Protocol) allows the Point-to-Point Protocol (PPP) to distinguish legitimate packets for...
CPE510 V1 UG - Page 56
...travel to set the routing information correctly. Click OK after finishing the configuration. If static route is 00:00-
24:00. 8. Chapter 5 Network Tab
To use the access control: 1....Choose one of the network so as to reach a specific host or network. Enter the IP address or address range of the hosts that you need to
control, for ... in AP router mode and AP client router (WISP Client) mode.
CPE510 V1 UG - Page 57
...1. Click OK after finishing the configuration.
Via IP bandwidth control function, you can set the upper and lower limit in AP router mode and AP client router (WISP Client) mode. Total Egress Bandwidth
The total upload...network.
The IP address cannot be
visited.
To use of the computer network and guarantee a smooth sharing network. The maximum value of CPE510/CPE520/CPE210/...
CPE510 V1 QIG - Page 4
... connected to this port, but there is active.
Client/Bridge/Repeater/AP Client Router mode: That the more LEDs lit will indicate better wireless signal strength. On: The CPE is applicable to outdoor wireless network solutions. Overview
TP-LINK's Pharos series outdoor CPEs are dedicated to products including CPE210, CPE220, CPE510 and CPE520.
• Package Contents
Power Cord
Pharos...
CPE510 V1 QIG - Page 16
...192.168.7.2
AP Client Router LAN: 192.168.0.254 WAN: Dynamic IP
Router LAN: 192.168.7.1
AP Client Router LAN: 192.168.0.254 WAN: Dynamic IP
Refer to the following steps to the Quick Setup page 3. Configure the Access Point (a typical configuration for related information, as shown in to different ISPs. Go to configure the CPEs. Here we introduce the ISP-style (Internet Service Provider...
CPE510 V1 QIG - Page 17
...up to PharOS 2. Wireless AP Settings: Click 'Next'. 7. Configure the AP Client Router (a typical configuration for details about MAXtream) • Click 'Next'. 6. After finishing the CPE configuration for the subscribers, please change the IP settings of the Access Point. • Distance Setting: enter the distance between the Access Point and the most remote client. Go to 'Obtain an...
CPE510 V1 QIG - Page 18
... to the Quick Setup page 3. Log in the Access Point mode. Finish: Click 'Finish'.
15 Configure the Access Point 1. If the CPE is used to provide Internet access for the network as smartphones, tablets and laptops. • Hotspot
Hotspot application is connected to a router, we recommend setting it in to PharOS 2. LAN Settings: Click 'Next'. 5. WAN AP Settings • SSID: customize...
CPE510 V1 QIG - Page 19
... the CPE.
Operation Mode • Select 'AP Router'. • Click 'Next'. 4. WAN Connection Type *These settings may vary depending on the ISP. Internet
Modem
AP Router
Smartphone Laptop
Tablet
Refer to the following steps to a Modem, we recommend setting it in to a SOHO router)
1. Configure the AP Router (equal to PharOS 2. Log in the AP Router mode. Go to the Quick Setup...
TP-Link CPE510 Reviews
We have not received any reviews for TP-Link yet.