TP-Link Auranet EAP220 Support and Manuals
Get Help and Manuals for this TP-Link item
View All Support Options Below
Free TP-Link Auranet EAP220 manuals!
Problems with TP-Link Auranet EAP220?
Ask a Question
Free TP-Link Auranet EAP220 manuals!
Problems with TP-Link Auranet EAP220?
Ask a Question
Popular TP-Link Auranet EAP220 Manual Pages
EAP Controller Software V2 User Guide - Page 2
... 1
1.1
System Requirements...1
1.2
Network Topology ...2
1.2.1 Layer-2 Management...2
1.2.2 Layer-3 Management...3
1.3
Software Installation...3
1.4
Quick Setup...5
Chapter 2 Interface 8
Chapter 3 Monitor 10
3.1
Map Tab ...10
3.1.1 Add Custom Maps...10
3.1.2 Set the Map Scale...11
3.1.3 Place APs onto the Map...12
3.2
Statistics Tab...14
3.2.1 View the Client Distribution...
EAP Controller Software V2 User Guide - Page 5
...a web browser on a business wireless network. Chapter 1 System Setup
The EAP Controller is recommended to deploy the EAP controller on a...all of the EAP series Business Wi-Fi Access Point models.
1.1 System Requirements
The computer that it allows you ...of each EAP in batches. This User Guide is particularly worth mentioning that installs the EAP Controller software has the following ...
EAP Controller Software V2 User Guide - Page 6
... Controller Host, other hosts' convenient login to the EAP Controller interface, it's recommended to set a static IP address to the note of the router is required to assign IP addresses to.... PC 1 and PC 2 do not need to install the EAP Controller software. It's assumed that the IP address of the LAN of Step 6 at Quick Setup.
2 1.2 Network Topology
1.2.1 Layer-2 Management
The typical...
EAP Controller Software V2 User Guide - Page 9
... shown as the following window will automatically open , please click Launch a Browser to Manage Wireless Network. Ensure that you have succeeded in installing the EAP Controller.
1.4 Quick Setup
Perform the following steps to hide this website. NOTE: If your country or region and click Next. You can
click Hide to...
EAP Controller Software V2 User Guide - Page 28
...while Radius stands for Remote Authentication Dial-In User Service.) Settings vary in different modes as the present valid key... other. If the Portal authentication is not supported in the following introduction. Select whether to this...password is necessary for Wi-Fi Protected Access, a security standard compatible with the wireless network without password. If you have to enter password...
EAP Controller Software V2 User Guide - Page 29
... is Auto, which includes AES and TKIP mechanisms. Encryption type TKIP is not supported in the 802.11n mode. Encryption: Select the Encryption type, including Auto,...- The default setting is an implementation of hexadecimal digits (0-9, a-f, A-F) in seconds.
25 Group Key Update Period: Specify the group key update period in the specified length. Radius Password: Set the shared secret...
EAP Controller Software V2 User Guide - Page 32
... allow the clients to access the specific subnets. Up to 16 subnets can be added. Part of network resources can be accessed by providing authentication service to the clients that you can.... NOTE: To apply Access Control on a wireless network, please go to Wireless Settings→Basic Wireless Setting to enable Access Control of a selected SSID.
28 Restricted Subnets：Enter the ...
EAP Controller Software V2 User Guide - Page 40
Check the Status box to add a new authentication policy and configure its parameters.
Assign the service port as the Destination IP Range. Add Free Authentication Policy
Step 1: Click
to enable the policy. Then set either Source IP Range with the destination IP address and subnet mask for free authentication policy. NOTE:
When External...
EAP Controller Software V2 User Guide - Page 45
...) for optimized throughput and better performance when handling differentiated wireless traffic, such as Voice-over-IP (VoIP), other types of service (QoS) on the selected Access Point during the time interval set for the profile. Associated with AP
In the Profile Name column, select a profile name from the drop-down list. Click...
EAP Controller Software V2 User Guide - Page 50
... to back up the settings before you to turn on/off the LED lights of EAPs.
4.3.5 Backup&Restore
You can directly specify a new username and password for them from being ...illegally adopted. If these EAPs have already been adopted, the Controller will change the EAP devices' username and password to each EAP device.
4.3.4 LED
The LED page allows you upgrade...
EAP110 V1 User Guide - Page 22
...enter the AP's SSID manually to connect to this AP... provides authentication service for WEP. Auto: The default setting is applied ...in 11b/g/n mode (in the 2.4GHz frequency band) or 11a/n (in 802.11n mode, the clients may work at a low transmission rate. SSID Isolation: After enabling SSID Isolation, the devices connected in 802.11n mode. If WEP is not supported...
EAP110 V1 User Guide - Page 64
... login. Both values are
Name/Password: case-sensitive, up to get the
Name/Password: permission of modification. System time is mainly used to configure some basic information like user account and time, and realize functions including reboot, reset, backup, restore and upgrade the device.
8.1 User Account
You can manually set the system time, configure the...
EAP Controller V2.2.3 User Guide - Page 32
...must enter the SSID manually to connect to a VLAN. For the network security, you are grouped to the EAP.
Wireless networks with each other.
Portal provides authentication service for the clients who...with the same VLAN ID are suggested to get authenticated before accessing the wireless network.
Set a VLAN ID for this SSID. Enabled by default. Select the security mode of...
EAP Controller V2.2.3 User Guide - Page 59
...Follow the steps below to upgrade the EAP devices in batches according to their model. 1. Visit http://www.tp-link.com/en/support/download/ to
restore the configuration. Then click Restore to download the latest firmware
file of the EAPs as .../Region On the Country/Region page, you back up the settings before upgrading the device. Batch Upgrade
Follow the steps below to System > Batch...
EAP Controller V2.2.3 User Guide - Page 62
... MAC address (or name you set), IP address, model, firmware version, the usage rate of... receiving and transmitting data.
57 4.1 View the Information of the EAP
Overview Click Overview to view the traffic information of the LAN port, including the total number of packets, the total size of data, the total number of packets loss, and the total size of error...
TP-Link Auranet EAP220 Reviews
We have not received any reviews for TP-Link yet.