Singer S0100 Serger Support and Manuals
Get Help and Manuals for this Singer item
View All Support Options Below
Free Singer S0100 Serger manuals!
Problems with Singer S0100 Serger?
Ask a Question
Free Singer S0100 Serger manuals!
Problems with Singer S0100 Serger?
Ask a Question
Most Recent Singer S0100 Serger Questions
Singer Serger S0100 Stitch Length Selection
On the manual for the machine it tells you to select stitch length N, but on the machine on the stit...
On the manual for the machine it tells you to select stitch length N, but on the machine on the stit...
(Posted by artandsharon 1 year ago)
Popular Singer S0100 Serger Manual Pages
User Manual - Page 1
INSTRUCTION MANUAL
S0100 / S0105
User Manual - Page 2
..., repair, electrical or mechanical adjustment.
• Never operate the sewing machine with any other user servicing adjustments mentioned in this manual.
...manual.
Always unplug this household sewing machine. WARNING - IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety precautions should always be followed, including the following:
Read all moving parts...
User Manual - Page 3
.... • If the cord connected with the foot control is securely installed. Never place other objects on cord. For Overlock Machines only: • Never operate without cutter cover or coverstitch table is damaged, it must be replaced by the
manufacturer or its service
agent or a similarly qualified person, in order to operate the...
User Manual - Page 4
...the power supply...........6 Replacing the stationary cutter 22 Setting up the telescopic thread stand 7 Storage 22 Opening and closing the front cover 7 Servicing 22 Removing and replacing the flat bed extension 7 Trouble shooting 23 Presser foot lift 8 Stitch table 24 Changing the needles 8 Fabric / Needle / Thread table 28 Changing the presser foot 8 Specifications 28 Disengage the...
User Manual - Page 14
... old thread. Remove the thread spool and place the new thread on the telescopic thread stand.
2.
Guide the fabric slightly with your left . Cut off the thread chain 2-5 cm behind the knot and... knots are any fabric or waste thread stuck between the blades.
3. First note tension dial settings and then turn the tension dials down to change threads:
1. Do not pull on the edge...
User Manual - Page 15
... thread tension becomes tighter. Tighten the thread tension of the lower looper (yellow) or loosen the thread tension of the lower looper (yellow). Thread tension settings
Set the thread tension to suit the type of the fabric. Right side
Wrong side Right side
Wrong side Right side
Wrong side Right side
When...
User Manual - Page 16
... and N. Both feed teeth work independently of each other . For overlock stitching on normal fabric, set the differential feed adjusting lever to the feed by the front feed teeth is changed in front and... back of stretching. N
Result
16 Therefore, test sew with different settings before sewing on your project. Use the differential feed to prevent stretching of knit fabrics...
User Manual - Page 17
... adjustment
The presser foot pressure is 3.5 mm.
B) When only the right needle is used the stitch width is pre-set on "N" for sewing based on your garment.
B) Right needle 3.5 mm
Stitch length settings
The stitch length dial should be increased or decreased by changing needle position
A) When only the left needle is...
User Manual - Page 18
...The rolled edge stitch is approximately 1.5 mm since the cutting width cannot be obtained by setting the stitch finger lever to the stitch table on your fabric
before sewing on pages 23-... rolled edge
3-thread rolled edge / narrow edge 1. The minimum overlock stitch width that can be set to change the degree of your garment. Use the right needle thread and the upper and lower ...
User Manual - Page 19
... adjusted correctly for ornamentation only on pages 23-26.
4. Flatlock sewing
A Flatlock Stitch is sewn with part of the stitch extending off the fabric.
5.
Unfold the fabric and pull on the underside of the fabric... pull into a straight line at the fabric edge.
6.
Set the thread tension according to create a Ladder Stitch.
2-thread flatlock stitch
Standard Flatlock Stitch
1.
User Manual - Page 22
... the following
directions.
If you have any difficulties, consult your
dealer to direct sunlight or humidity.
Replacing the stationary cutter
1
Turn off the main power switch and unplug the machine. Open the front cover and set screw (2) and remove the stationary cutter (3).
3. Storage
When the machine is not in the groove of...
User Manual - Page 23
... Insert needle correctly. - Decrease presser foot pressure for heavy weight fabric. - Tighten needle set screw. - Loosen thread tension. - Shorten stitch length. - Increase presser foot pressure for...for tangled or caught thread. - Replace one or both cutters. - Loosen thread tension. - Check for tangled or caught thread. - Trouble shooting
Problem Fabric does not feed well Needle ...
User Manual - Page 24
Woven heavy denim, canvas, terrycloth, etc.
For best results make tension adjustments in this table are using.
Please note:
The settings shown in small increments of your fabric before sewing on a sample of no greater than half a number at a time. Stretch heavy sweather knits, fleece, etc. ...
User Manual - Page 29
...get into the food chain, damaging your health and well-being. When replacing old appliances with relevant National legislation relating to electrical/electronic products. Such ... information regarding the collection systems available.
INTELLECTUAL PROPERTY SINGER, and the Cameo "S" Design, are disposed of The Singer Company Limited S.à.r.l.
Do not dispose of accessories...
User Manual - Page 32
or its Affiliates. • All rights reserved • Printed on environment friendly paper 471075126 A • English • ©2020 The Singer Company Limited S.à.r.l.
Singer S0100 Serger Reviews
We have not received any reviews for Singer yet.