Singer ProFinish 14CG754 Serger Refurbished Support and Manuals
Get Help and Manuals for this Singer item
View All Support Options Below
Free Singer ProFinish 14CG754 Serger Refurbished manuals!
Problems with Singer ProFinish 14CG754 Serger Refurbished?
Ask a Question
Free Singer ProFinish 14CG754 Serger Refurbished manuals!
Problems with Singer ProFinish 14CG754 Serger Refurbished?
Ask a Question
Popular Singer ProFinish 14CG754 Serger Refurbished Manual Pages
Instruction Manual 15 - Page 2
...guide page by authorized dealer.
®Singer is a registered trademark of this sewing machine when considered necessary without supervision. * Young children should be replace by page. IMPORTANT SAFETY INSTRUCTIONS
Ak
* If the supply cord is damaged, it must be replaced...the most out of your purchase of The Singer Company Limited or its service agent or a similarly qualified person in ...
Instruction Manual 15 - Page 7
...
Needle Positions
Tension Dial: Numbers shown are average settings on this page as well as the dials are suggested guides. For best results make tension adjustments in small ...
2.0
Upper looper
35
The thread tension becomes tighter as throughout the operator's manual are turned to suit the fabric and size of no greater than half a number at a time
6 Adjust thread tensions ...
Instruction Manual 15 - Page 8
... size 90/14 is readjusted, skipping of the stitches may be used. However, unless the suggested tension setting is furnished with the machine.
• In an emergency, standard Singer needle #2020 may occur. Sizes available
Singer needle #2022
80/11 90/14
7 3. ACCESSORIES
I
Accessories are contained in the accessory case in the cloth...
Instruction Manual 15 - Page 9
PRINCIPAL PARTS
1 Thread guides and holder 2 Handle 3 Left needle thread tension dial (blue) 4 Right needle thread tension dial (green) 5 Upper looper thread tension dial (orange) 6 Lower looper thread tension ... Hand wheel 13 Spool stand 14 Spool holder 15 Spool pin 16 Presser bar lifter 17 Differential feed adjusting lever knob 18 Seam width finger support plate
0
8 5.
Instruction Manual 15 - Page 11
...than the other).
Handle the foot controller with the thread guide holder in use. PREPARATION FOR THREADING
Setting Up the Thread Guide Holder
• This machine is the same as the rated... plug (one way. If it on the spool pins. Be sure not to install the proper outlet. SINGER
• Center the thread guides above the spool pins.
• Place thread over the cone adapters on the ...
Instruction Manual 15 - Page 12
...; Remove the needle(s). ii
aserentl-
• Loosen, but do not remove the needle set screw with the flat surface to the back.
• Insert the needle into the needle clamp as far as it difficult to remove and replace the needle.
.2'
-00
Flat surface to the rear ,,:„
7
11 10.
To Insert...
Instruction Manual 15 - Page 14
...; Pull about 10cm (4 inches) of thread through the looper and place to the back of the machine following the orange color coded thread guides ( 4 - 7 ). Note: Use of tweezers provided in the accessory set to aid in the upper looper from front to make certain it is properly located in between the tension discs...
Instruction Manual 15 - Page 16
...set to aid in the end of the looper 10 . SINGER
4
SING
:Or
••
0
7
xl (1'0 C)
co
0
15 Note: Use the tweezers provided in the accessory set... and to the left of threading guide 8.
• Pull the thread up and into thread guide 8.
• Pass the thread behind... the tweezers 4 cm (1-1/2 inches) from thread guide 7.
• Place the thread with the point of the tweezers ...
Instruction Manual 15 - Page 18
Note: Use of tweezers in the accessory set will make needle eye threading easy.
• Draw about 10cm (4 inches) of thread through needle eye to hang free.
• Place the thread to pass the thread through upper thread path of the thread guide 6.
• Thread the eye of the right needle 8 . I
tl 0 7
10cm...
Instruction Manual 15 - Page 20
Important Threading Information
• Always thread the needle(s) last to thread points 4 - 6 . Note: Use of tweezers in the accessory set will make needle eye threading easy.
• Draw about 10cm (4 inches) of thread through lower thread path of the left needle 7 ... free.
• Place the thread to the back, under the presser foot.
I
• Thread the eye of the thread guide 5.
Instruction Manual 15 - Page 21
... • Tie new thread and old thread ends together. • Clip thread tails to previous settings.
20
SINGER HOW TO CHANGE THREADS / TIE ON METHOD
• To change thread type or color, clip thread... near the spool.
• Place new thread on
thread guides or looping under thread stand. • ...
Instruction Manual 15 - Page 25
... "1.0" for sewing decorative collars, sleeves, skirt hems, etc.
Note: * If amount of the presser foot. on loosely knit and woven fabrics. To set the differential feed adjusting lever
• Set differential feed adjusting lever knob above graduation "1.0".
• To sew a seam, apply gentle tension to the fabric by holding the seam lightly...
Instruction Manual 15 - Page 29
... Cn
Note: Be sure to push seam width finger knob as far as it will go in the direction of setting S . STANDARD OVEREDGE AND ROLLED HEM STITCHING
To Sew Standard Overedge
• Set seam width finger knob to S to move seam width finger to retract the seam width finger. S
28
Seam width...
Instruction Manual 15 - Page 37
...be sewn.
• Needle: Singer Needle #2022 size 80/11 or 90/14
• Thread: A variety of thread combinations can sew four types of seam width finger support plate
with R mark on ...throat plate by rolling and overedging the fabric edge.
• Light weight fabrics such as required.
• Set stitch length dial to setting R . (See
...
Instruction Manual 15 - Page 49
...foot pressure. - Balance thread tension. - Loosen thread tension. - Replace one or both knives.
-
TROUBLE SHOOTING CHART
Problem
Solution
Fabric does not feed well Needle breaks Thread breaks
Stitches skip
...for tangled or caught thread. - 26. Do not pull fabric while sewing. - Tighten needle set screw. - Insert new needle, current needle may be bent or have a
blunt point. - ...
Singer ProFinish 14CG754 Serger Refurbished Reviews
We have not received any reviews for Singer yet.