Service Manual
Page 1
ONLY) SHARP CORPORATION This document has been published to be used for after sales service only. S3333CDE500// Illustration CD-E500/E55 Illustration CD-E44 MINI COMPONENT SYSTEM MODEL CD-E500 CD-E500 Mini Component System consisting of CD-E55 (main unit) and CP-E55 (speaker system). CONTENTS Page IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY) ... to change without notice. The contents are subject to those specified be used . MODEL CD-E55 CD-E55 Mini Component System consisting of CD-E500 (main unit) and CP-E500 (speaker system). CD-E500 CD-E55/E44 SERVICE MANUAL No.
ONLY) SHARP CORPORATION This document has been published to be used for after sales service only. S3333CDE500// Illustration CD-E500/E55 Illustration CD-E44 MINI COMPONENT SYSTEM MODEL CD-E500 CD-E500 Mini Component System consisting of CD-E55 (main unit) and CP-E55 (speaker system). CONTENTS Page IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY) ... to change without notice. The contents are subject to those specified be used . MODEL CD-E55 CD-E55 Mini Component System consisting of CD-E500 (main unit) and CP-E500 (speaker system). CD-E500 CD-E55/E44 SERVICE MANUAL No.
Service Manual
Page 2
...(Except for leakage current in series with 1000 ohm per volt, or higher, sensitivity to the owner. Any reading of 0.3 volt RMS (this model are not pinched or that no shock hazard exists, check for Canada) Output power Output terminals Input terminals 50 watts minimum RMS per channel into...AC outlet. * Using two clip leads, connect a 1.5 kohm, 10 watt resistor paralleled by a 0.15 µF capacitor in the following safety checks. 1. CD-E500 CD-E55/E44 IMPORTANT SERVICE NOTES (FOR U.S.A. FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.
...(Except for leakage current in series with 1000 ohm per volt, or higher, sensitivity to the owner. Any reading of 0.3 volt RMS (this model are not pinched or that no shock hazard exists, check for Canada) Output power Output terminals Input terminals 50 watts minimum RMS per channel into...AC outlet. * Using two clip leads, connect a 1.5 kohm, 10 watt resistor paralleled by a 0.15 µF capacitor in the following safety checks. 1. CD-E500 CD-E55/E44 IMPORTANT SERVICE NOTES (FOR U.S.A. FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.
Service Manual
Page 14
...is provided with the same buttons. Request: Every period include 4 operation. PU-IN buttons: REW/PRESET DOWN + CD STOP Since this model is displayed. After open finish rotate 1 circle close delay 3S after close finished, tray rotate 1 circle (360 ...CD MECHANISM Aging Test Mode (TEST 8) OPEN/CLOSE & 3 DISC CHANGER aging test. All models using this test mode, it is not determined. The order of microcomputer are not always provided with SURROUND (HAVE OR NOT), and electric CD lid, the following is displayed. Then close, After close finish rotate 1 circle - 14 - CD-E500 CD-E55...
...is provided with the same buttons. Request: Every period include 4 operation. PU-IN buttons: REW/PRESET DOWN + CD STOP Since this model is displayed. After open finish rotate 1 circle close delay 3S after close finished, tray rotate 1 circle (360 ...CD MECHANISM Aging Test Mode (TEST 8) OPEN/CLOSE & 3 DISC CHANGER aging test. All models using this test mode, it is not determined. The order of microcomputer are not always provided with SURROUND (HAVE OR NOT), and electric CD lid, the following is displayed. Then close, After close finish rotate 1 circle - 14 - CD-E500 CD-E55...
Service Manual
Page 15
...P is used : the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without such a symbol is microfarad. In the CD section, the CD is stopped. • Parts marked with " 1 " ( ) are subject to replace these parts with no signal given. 1. NO SW1 SW401 SW402 .... In the main section, a tape is being played back. 5. NOTES ON SCHEMATIC DIAGRAM CD-E500 CD-E55/E44 • Resistor: To differentiate the units of resistors, such symbol as K and M are used : this model are important for maintaining the safety and performance of the set . In the power section,...
...P is used : the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without such a symbol is microfarad. In the CD section, the CD is stopped. • Parts marked with " 1 " ( ) are subject to replace these parts with no signal given. 1. NO SW1 SW401 SW402 .... In the main section, a tape is being played back. 5. NOTES ON SCHEMATIC DIAGRAM CD-E500 CD-E55/E44 • Resistor: To differentiate the units of resistors, such symbol as K and M are used : this model are important for maintaining the safety and performance of the set . In the power section,...
Service Manual
Page 51
... nearest SHARP Parts Distributor to replace parts with " " are important for maintaining the safety and performance of CD-E44 (main unit) and CP-E44 (speaker system). MODEL NUMBER 2. MODEL CD-E55 CD-E55 Mini Component System consisting of CD-E500 (main unit) and CP-E500 (speaker system). Be sure to order. 3. PARTS GUIDE CD-E500 CD-E55/E44 MINI COMPONENT SYSTEM MODEL CD-E500 CD...
... nearest SHARP Parts Distributor to replace parts with " " are important for maintaining the safety and performance of CD-E44 (main unit) and CP-E44 (speaker system). MODEL NUMBER 2. MODEL CD-E55 CD-E55 Mini Component System consisting of CD-E500 (main unit) and CP-E500 (speaker system). Be sure to order. 3. PARTS GUIDE CD-E500 CD-E55/E44 MINI COMPONENT SYSTEM MODEL CD-E500 CD...