SanDisk SDDR-01 - ImageMate External Parallel CompactFlash Card Reader Support and Manuals
Get Help and Manuals for this SanDisk item
This item is in your list!
View All Support Options Below
Free SanDisk SDDR-01 manuals!
Problems with SanDisk SDDR-01?
Ask a Question
Free SanDisk SDDR-01 manuals!
Problems with SanDisk SDDR-01?
Ask a Question
Popular SanDisk SDDR-01 Manual Pages
Product Manual - Page 29
... resistor on card (if present)
tpf
VCC Min.
SanDisk CompactFlash Card OEM Product Manual
Interface Description
Figure 3-2 Power Up/Power Down Timing for all types of memory. trec
VIH
2V
3.3.4
Common Memory Read Timing Table 3-10 contains common memory read timing specifications for Systems not supporting RESET
tpr
VCC Min. NOTE: All timings measured...
Product Manual - Page 36
...SanDisk CompactFlash Card OEM Product Manual
Figure 3-7 Register Transfer to/from Device
NOTE 1: NOTE 2:
Device address consists of /IORD to the time that t0 is equal to or greater than the sum of t0, t2, and t2i shall be met. data setup... in the devices IDENTIFY DEVICE data. A device imple mentation shall support any legal host implementation. pulse width 8-bit (min.)
t2i a
IORD...
Product Manual - Page 38
... actual command inactive time. A device imple mentation shall support any legal host implementation. NOTE: SanDisk CompactFlash Memory cards do not assert an -IORDY signal. pulse ...
© 2007 SanDisk Corporation setup
(min.) t2a IORD-/IOWR- data setup (min.) t4 IOWR- data hold (min.) t5 IORD- Interface Description
SanDisk CompactFlash Card OEM Product Manual
The PIO data ...
Product Manual - Page 43
SanDisk CompactFlash Card OEM Product Manual
Interface Description
Pin replacement... Table 3-22 Common Memory Function
Function Code Standby Byte Read Access (8 bits)
Byte...Set by the software when the register is supported. This register is reserved for the I/O Transfer function.
3.5.1
Common Memory Function
The Common Memory transfer to or from SanDisk CompactFlash memory cards can be set...
Product Manual - Page 49
... status condition:
(Not Ready, Write Fault, etc.) or when an invalid command has been
issued. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2- D1
0
Bit set to be found.
Offset 1, 0Dh Write Only)
This register provides information about the source of...
Product Manual - Page 51
... card is locked out from
the host through the Data Register. No other bits in the Error Register contain additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376];
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status Registers (Address-1F7[177]&3F6[376]; Reading the Status Register...
Product Manual - Page 59
...supported Capabilities: DMA Supported (bit 8), LBA supported (bit 9) Reserved
© 2007 SanDisk Corporation
5-5
Rev. 12.0, 02/07 This command has the same protocol as the Read Sector(s) command.
All reserved bits or words are "0". SanDisk CompactFlash Card OEM Product Manual... Long Commands Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ...
Product Manual - Page 64
...
SanDisk CompactFlash Card OEM Product Manual
Word 68: Minimum PIO Transfer Cycle Time With Flow Control. Bit 14 of Word 83 and Word 84 will be set to "1," and bit 15 of these words by CompactFlash cards prior to ATA-3 and will be depended on by CF Card
4
0
Removable Media Status feature set not supported...
Product Manual - Page 65
... Set Password command
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not enabled
5
1
Write cache enabled
6
1
Look-ahead enabled
7
0
Release Interrupt not enabled
8
0
Service Interrupt not enabled
9
0
Device Reset command not supported
10
0
Host Protected Area feature set not supported by Set...
Product Manual - Page 70
...block transfer is pending in the sector buffer.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read Multiple-C4H
The Read Multiple command performs similarly to... is set and the data transfer will take place as that contained the error.
02/07, Rev. 12.0
5-16
© 2007 SanDisk Corporation
The transfer begins at the sector where the error occurred....
Product Manual - Page 73
...-8)
Sec Num (3)
Sector Number (LBA 7-0)
Sec Cnt (2)
X
Feature (1)
X
© 2007 SanDisk Corporation
5-19
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product. Table 5-24 Extended Error Codes
Extended Error Code 00h 01h 09h 20h 21h 2Fh
35h, 36h 11h 18h...
Product Manual - Page 74
... no impact on Reset (POR) establishment of defaults at Soft Reset. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is issued, all features that are not part of the ATA Specification. Table 5-27 Features Supported
Feature 01h 02h 03h 55h 66h 69h
81h 96h
9Ah
BBh CCh
Operation Enable...
Product Manual - Page 106
...: product model number and description, serial numbers, nature of defect, conditions of use in the same way as new products, provided such cards meet the original product's specifications. SanDisk may also have other than its discretion, ship repaired or rebuilt products identified in other rights that vary from SanDisk Corporation.
Please contact SanDisk's OEM Support Department at...
User Guide - Page 3
... application 1. Go to www.sandisk.com/imagemate to launch every time you connect the ImageMate Reader/Writer on a Macintosh operating system, removable disk icons labeled 'no name' representing the card slots show up . B. Double click on the removable disk drive (for model
SDDR-189/SDDR-199. 2. When the Drive Letter application has been installed (see above ), the...
User Guide - Page 4
...Trash. 2.
Macintosh 1.
For technical support and warranty service, please go to www.sandisk.com/techsupport to do so, unplug the ImageMate Reader/Writer from the USB port ...XP and Vista: 1. In the notification area, right-click on error messages, please check our knowledgebase at kb.sandisk.com. Select the device you should NEVER remove the device from your computer. Troubleshooting...
SanDisk SDDR-01 Reviews
Do you have an experience with the SanDisk SDDR-01 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for SanDisk yet.
Earn 750 points for your review!