SanDisk SDCFB-64-455 - CompactFlash Flash Memory Card Support and Manuals
Get Help and Manuals for this SanDisk item
View All Support Options Below
Free SanDisk SDCFB-64-455 manuals!
Problems with SanDisk SDCFB-64-455?
Ask a Question
Free SanDisk SDCFB-64-455 manuals!
Problems with SanDisk SDCFB-64-455?
Ask a Question
Popular SanDisk SDCFB-64-455 Manual Pages
Product Manual - Page 28
Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in Table 3-9 was defined to permit peripheral cards to perform powerup initialization.
Table 3-9 Power Up/Power Down Timing
Item
Value
CE Signal Levela
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width...
Product Manual - Page 29
... Enable Time from -CE Output Enable Time from -OE Data Valid from the system driver/receiver to the card must be accounted for by pull-up resistor on card (if present)
tpf
VCC Min.
SanDisk CompactFlash Card OEM Product Manual
Interface Description
Figure 3-2 Power Up/Power Down Timing for all types of memory...
Product Manual - Page 35
... host. Transfer Timing. Min. (ns) 60 30 165 70 20 5 20 5 0 ---------
SanDisk CompactFlash Card OEM Product Manual
Interface Description
Table 3-14 contains the specification information related to the asserted condi tion.
The minimum cycle time supported by the associated mode (e.g., a device supporting PIO Mode 4 timing will be greater than or equal to the minimum...
Product Manual - Page 36
... that t0 is the minimum command recovery time or command inactive time.
data setup (min.)
t6
IORD- This parameter specifies the time from Device
PIO Timing ... support any legal host implementation. pulse width 8-bit (min.)
t2i a
IORD-/IOWR- Table 3-15 Register Transfer to/from the negation edge of t2 and t2i. Interface Description
SanDisk CompactFlash Card OEM Product Manual...
Product Manual - Page 38
...the value reported in Table 3-16. A device imple mentation shall support any legal host implementation. b. data setup (min.) t4 IOWR- pulse width 16-bit (min.) t2ia IORD-/IOWR-...setup
(min.) t2a IORD-/IOWR- The three timing requirements of cards that t0 is the minimum command recovery time or command inactive time. Interface Description
SanDisk CompactFlash Card OEM Product Manual...
Product Manual - Page 42
...Interface Description
SanDisk CompactFlash Card OEM Product Manual
Card Configuration and Status Register (con't)
Bit
Name
Description
D7
Changed Indicates that caused the interrupt request has been
serviced. If...becomes BUSY when this bit is a "0".
3.4.4
Pin Replacement Register (Address 204h in the Device Control
Register, this bit is set , -STSCHG Pin 46
is held high while the
...
Product Manual - Page 49
... Address (LBA) for any CompactFlash Memory Card data access for the subsequent command.
© 2007 SanDisk Corporation
4-5
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2-
This register is encountered. Offset 1, 0Dh Read Only)
This register contains...
Product Manual - Page 51
...
X
1
SW Rst
-IEn
0
© 2007 SanDisk Corporation
4-7
Rev. 12.0, 02/07
The meaning of performing card operations.
D2
CORR
Set when a correctable data error has been encountered and the data has
been corrected. ... until card is ready. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status Registers (Address-1F7[177]&3F6[...
Product Manual - Page 59
...byte increments Number of Sectors on Read/Write Long Commands Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) Big Endian Byte ... not supported Capabilities: DMA Supported (bit 8), LBA supported (bit 9) Reserved
© 2007 SanDisk Corporation
5-5
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
ATA Command...
Product Manual - Page 64
...
Write cache supported
6
1
Look-ahead supported
7
0
Release Interrupt not supported
8
0
Service Interrupt not supported
9
0
Device Reset command not supported
10
0
Host Protected Area feature set not supported by CF Card
15
--- Words 85, 86, and 87 indicates features/ command sets enabled.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
Word...
Product Manual - Page 65
....
SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Bits 0-13 of Advanced PIO timing modes and Advanced Multiword DMA timing modes. Table 5-11 Word 85 Description
Bit
Setting
Indication
0
0
SMART feature set not enabled
1
1
Security Mode feature set enabled via the Security Set Password command
2
0
Removable Media feature set not supported
3
1
Power...
Product Manual - Page 70
... the Read Multiple command. If an error occurs, the read . The Command Block registers contain the cylinder, head and sector number of 0 requests 256 sectors. Subsequent blocks or partial blocks are posted at the beginning of each sector. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read Multiple-C4H
The Read...
Product Manual - Page 73
... (LBA 27-24)
Cylinder High (LBA 23-16)
Cyl Low (4)
Cylinder Low (LBA 15-8)
Sec Num (3)
Sector Number (LBA 7-0)
Sec Cnt (2)
X
Feature (1)
X
© 2007 SanDisk Corporation
5-19
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product.
Product Manual - Page 74
...occur on Reset (POR) establishment of the ATA Specification. The 9AH feature is unique to CompactFlash Memory cards and are not part of defaults at Soft Reset Accepted for backward ...select certain features. Features 01H and 81H are supported. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is used to enable and clear 8-bit ...
Product Manual - Page 106
...failure.
RECEIVING WARRANTY SERVICE
According to SanDisk's warranty procedure, ...specifications.
Upon confirmation of this limited warranty shall be returned. SanDisk reserves the right to repair or replace, at its normal and customary manner, misuse, accident or neglect; or improper alterations or repairs. Please contact SanDisk's OEM Support Department at its discretion, ship repaired...
SanDisk SDCFB-64-455 Reviews
We have not received any reviews for SanDisk yet.