SanDisk SDCFB-32-455 - CompactFlash Flash Memory Card Support and Manuals
Get Help and Manuals for this SanDisk item
View All Support Options Below
Free SanDisk SDCFB-32-455 manuals!
Problems with SanDisk SDCFB-32-455?
Ask a Question
Free SanDisk SDCFB-32-455 manuals!
Problems with SanDisk SDCFB-32-455?
Ask a Question
Popular SanDisk SDCFB-32-455 Manual Pages
Product Manual - Page 28
...
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width
Symbol Vi (CE)
TSU (VCC) TSU (RESET) TREC (VCC)
tpr tpf TW (RESET) Th (Hi-z Reset) TS (Hi-z Reset)
Condition 0V Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in...
Product Manual - Page 29
...specifications for Systems not supporting RESET
tpr
VCC Min.
Table 3-10 Common Memory Read Timing Specification...driver/receiver to the card must be accounted for by pull-up resistor on card (if present)
tpf
VCC Min. Skews and delays from Add Changea Address Setup... 2007 SanDisk Corporation
3-11
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
Interface Description
Figure 3-2 Power...
Product Manual - Page 35
... the interface signals for the True IDE mode. SanDisk CompactFlash Card OEM Product Manual
Interface Description
Table 3-14 contains the specification information related to the I /O Write Timing Specification
Item Data Setup before -IOWR Data Hold following -IOWR -IOWR Width Time Address Setup before -IOWR Address Hold following -IOWR -CE Setup before -IOWR -CE Hold following -IOWR -REG...
Product Manual - Page 36
...5 30 10
a. setup (min.)
t2 a
IORD-/IOWR- data hold (min.)
t6z b
IORD- to or greater than the sum of DD(7:0). A device imple mentation shall support any legal host implementation... command active time and the actual command inactive time. Interface Description
SanDisk CompactFlash Card OEM Product Manual
Figure 3-7 Register Transfer to/from Device
PIO Timing Parameters
t0 a...
Product Manual - Page 38
...- A device imple mentation shall support any legal host implementation. data setup (min.) t4 IOWR- The actual cycle time equals the sum of t2 and t2i. The three timing requirements of cards that are located in the Card Information Structure (CIS).
Interface Description
SanDisk CompactFlash Card OEM Product Manual
The PIO data transfer parameters...
Product Manual - Page 42
...card. Interface Description
SanDisk CompactFlash Card OEM Product Manual
Card Configuration and Status Register (con't)
Bit
Name
Description
D7
Changed Indicates that caused the interrupt request has been
serviced. When the Changed... Pin Replacement Register CRdy, or
CWProt bits are disabled by the host to enable and disable a state-change signal is desired, this bit should
be set to...
Product Manual - Page 49
... CompactFlash Memory Card data access for the subsequent command.
© 2007 SanDisk Corporation
4-5
Rev. 12.0, 02/07 D6
UNC
Set when an uncorrectable error is detected. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2-
If the value in this register is specified. If...
Product Manual - Page 51
... Register contain additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376];
Offsets 7 & Eh)
These registers return the card status when read
operation. D3
DRQ
Set when the card requires that information be transferred either to a 1. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status...
Product Manual - Page 59
...Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) Big Endian Byte Order in Word Maximum No. of ECC bytes passed on Read/Write Multiple command Double-word not supported Capabilities: DMA Supported (bit 8), LBA supported (bit 9) Reserved
© 2007 SanDisk... Table 5-8. SanDisk CompactFlash Card OEM Product Manual
ATA Command...
Product Manual - Page 64
... are reserved.
02/07, Rev. 12.0
5-10
© 2007 SanDisk Corporation
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
Word 68: Minimum PIO Transfer Cycle Time With Flow Control. Words 82, 83, and 84 indicate the features and command sets supported.
Bits 1 through 13 of these words by CompactFlash cards prior to "1," and bit...
Product Manual - Page 65
... enabled
5
1
Write cache enabled
6
1
Look-ahead enabled
7
0
Release Interrupt not enabled
8
0
Service Interrupt not enabled
9
0
Device Reset command not supported
10
0
Host Protected Area feature set not supported by host implementers. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Bits 0-13 of word 87 are reported in these words should not be cleared...
Product Manual - Page 70
... programmed by the Set Multiple Mode command, which contains the number of the block that contained the error.
02/07, Rev. 12.0
5-16
© 2007 SanDisk Corporation This command ...A sector count of blocks or the block count) requested. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read Multiple-C4H
The Read Multiple command performs similarly to the Read ...
Product Manual - Page 73
SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product.
This command must be the next command issued to the host in the Error Register. Table 5-25 Seek
Bit
7
6
5
4
3
2
1
0
Command (7)
7XH
C/D/H (6) Cyl High (5)
1
LBA
1
Drive
Head (LBA 27-24)
Cylinder High (...
Product Manual - Page 74
... to establish or select certain features.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is unique to CompactFlash Memory cards and are not part of the ATA Specification. If the 01H feature command is issued, all features that are supported. The 9AH feature is used to enable and clear...
Product Manual - Page 106
..., whether new, repaired, or rebuilt, under no obligation to do not meet or exceed the same published specifications as new products, provided such cards meet the original product's specifications. RECEIVING WARRANTY SERVICE
According to SanDisk's warranty procedure, defective product should be returned. Limited Warranty
SanDisk CompactFlash Card OEM Product Manual
All failing products...
SanDisk SDCFB-32-455 Reviews
We have not received any reviews for SanDisk yet.