Ryobi RTS21 Support and Manuals
Get Help and Manuals for this Ryobi item
Most Recent Ryobi RTS21 Questions
Can't Raise/lower Blade
Hello. There are 2 screws that go through a plate involved in raising and lowering the blade. One is...
Hello. There are 2 screws that go through a plate involved in raising and lowering the blade. One is...
(Posted by info10977 7 years ago)
Vibration In My Table Saw
I tried a 8in dia dado stack of 1/4 in, the saw vibrated so bad the blades retracted down in the saw...
I tried a 8in dia dado stack of 1/4 in, the saw vibrated so bad the blades retracted down in the saw...
(Posted by Lbtrail 8 years ago)
Bt3000 Part No. 44
part 44 hex bolt vibrated out. how do i gain access to replace it
part 44 hex bolt vibrated out. how do i gain access to replace it
(Posted by carlsr1581 8 years ago)
Popular Ryobi RTS21 Manual Pages
English Manual - Page 11
... for a cross cut , with optional clamps and accessories. Always keep the kerf open and prevent kickback. MITER GAUGE GROOVEs -
SLIDING TABLE EXTENSIONS - carbide blade. Bevel LOCKING LEVER - HEIGHT/BEVEL ADJUSTING HANDWHEEL - OUTFEED SUPPORT - SPREADER -
BLADE GUARD - MITER GAUGE - RIP FENCE - SCALE -
This saw blade, which the workpiece is secured with the height...
English Manual - Page 32
... the wood as it .
Place a support (the same height as rabbets or dadoes. BLADE GUARD REMOVED
NON-THROUGH CUT
PUSH STICK
WARNING:
When making any non-through cut is made without the blade guard installed.
For example, if your non-through cut such as saw table) behind the saw .
Remove the blade guard assembly.
Turn the bevel lock lever to...
English Manual - Page 33
... washer and the spacer.
Reinstall the inner blade washer.
Mount the dado blade, using the blade and chippers appropriate for the blade to come to make a bevel dado cut.
Unplug the saw.
Remove the blade guard assembly, throat plate, and the saw cannot be used .
Install the dado throat plate and rotate the blade by hand to make sure both the inner...
English Manual - Page 37
Make sure the throat plate is required. DO NOT use only identical Ryobi replacement parts. Therefore, no further lubrication is in good condition and in the blade teeth. If operation is dusty, also wear a dust mask. GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are lubricated with plastic parts.
MAINTENANCE
WARNING:
When servicing, use any ...
User Manual - Page 10
... for through-sawing cuts. MITER GAUGE GROOVES - This table extension at the back of this tool. Located on the front rail, the easy-to help prevent or reduce the possibility of kickback. SLIDING TABLE EXTENSION - SWITCH ASSEMBLY - The teeth on the tool and in this warning could result in personal injury.
BLADE GUARD - MITER GAUGE -
A sturdy metal fence guides the workpiece...
User Manual - Page 34
... Place release lever in locked position. Install the dado throat plate and rotate the blade by hand to manufacturer instructions, using the blade and chippers appropriate for use either the rip fence or miter gauge. Turn the saw on this manual and check with a 6 in a secure location. Mount the dado blade, according to make sure it turns freely then lower...
User Manual - Page 37
... and may be moved.
Place a framing square beside the blade and move the rip fence up to remove dirt, dust, oil, grease, etc. Therefore, no further lubrication is in good condition and in position.
Check the blade guard assembly. To maintain the table surfaces, fence, and rails,
periodically apply paste wax to them and buff...
User Manual - Page 38
...Replace blade. Rip fence does not move smoothly.
Rip fence does not lock at retail stores: 089037011021 Dado Throat Plate
WARNING:
Current attachments and accessories available for use of attachments or accessories not recommended can result in the Assembly section.
Cutting binds or burns work. Blade is warped. Wood is dull. See page 28 on flat surface. Resharpen or set . Blade...
User Manual 4 - Page 4
... 1 Saw Table 1 Outfeed Support Bracket 2 Rip Fence Assembly (See Figure C 1 Front Blade Guard Warning Label (Left 1 Front Blade Guard Warning Label (Right)......... 1 No Hands Warning Label 2 Guard Warning Label (Left 1 Guard Warning Label (Right 1 Warning Label (Upper Barrier 1
Dado Throat Plate (Optional 1 Operator's Manual (089037011908)
4 TABLE SAW - MODEL NUMBER RTS21
The model...
User Manual 5 - Page 11
... and in personal injury.
This table extension at the back of kickback. RIP FENCE - A removable metal piece of the blade guard assembly, slightly thinner than the speed of this operator's manual as well as a knowledge of the information on the saw blade teeth and becomes a riving knife. BLADE GUARD - The miter gauge rides in the non-through sawing, or "up" position, it is...
User Manual 5 - Page 35
... flush against the rip fence or miter gauge and hold firmly against the saw table.
Use a push block or push stick to full speed before you turn the saw . Never push a small piece of this procedure (see the Accessories section of wood into the blade.
Position the workpiece flat on . An optional dado throat plate is fully engaged and...
User Manual 5 - Page 38
... in position.
Check the blade guard assembly. To maintain the table surfaces, fence, and rails,
periodically apply paste wax to them and buff to provide smooth functioning. Protect the blade by their use.
WARNING:
Before performing any aerosol or petroleum solvents. GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. LUBRICATION
All of the...
User Manual 5 - Page 39
... stand.
Adjust clamp screw clockwise. Cutting binds or burns work. Replace or sharpen blade. Blade is out of balance.
Work is damaged. Always cut with this tool. Blade is fed too fast.
Rip fence does not lock at retail stores: 089037008711 Dado Throat Plate with Special Washer
WARNING:
Current attachments and accessories available for use with convex side to table...
User Manual 8 - Page 3
... Outfeed Support 1 089037008908 Warning Label 1 089037008705 Anti-Kickback Pawls 1 089037008061 Throat Plate Assembly 1 089037008704 Blade Guard Assembly 1 089037008703 Spreader/Riving Knife Assembly 1 089037008060 Screw (M6 x 16 mm, Hex. RYOBI 10 in . Always mention the model number in all correspondence regarding your 10 in . PARTS LIST FOR FIGURE A
KEY PART
NO...
User Manual 12 - Page 3
Always mention the model number in ., INTERNAL TOOTH 1
0121010317 DADO THROAT PLATE (NOT SHOWN 1
3 TABLE SAW - MODEL NUMBER BTS16
The model number will be found on a label attached to the motor housing.
x 16 x 1t 2
0121010321
FRONT GUARD 1
410251018 BOLT (M6 x 8 mm 2
412042702 LOCK WASHER (1/4 in., EXTERNAL TOOTH 1
410079021 SCREW (M5 x 6 mm SOC 1
0121010802 WING ...
Ryobi RTS21 Reviews
We have not received any reviews for Ryobi yet.