English Manual
Page 9
Pilot Hole (drill presses) A small hole drilled in a workpiece that serves as a spreader or splitter. Resaw A cutting operation to ... front of the saw blade tooth is bent (or set) outward from a block so the end (or part of the end) is angled rather than 90° to the table surface. Compound Cut A cross cut ... operation made with the workpiece at any angle other aids. Worktable Surface where the workpiece rests while performing a cutting, drilling, planing, or sanding operation. 9 Bevel Cut A cutting operation made with the blade at any ripping operation. Dado ...
Pilot Hole (drill presses) A small hole drilled in a workpiece that serves as a spreader or splitter. Resaw A cutting operation to ... front of the saw blade tooth is bent (or set) outward from a block so the end (or part of the end) is angled rather than 90° to the table surface. Compound Cut A cross cut ... operation made with the workpiece at any angle other aids. Worktable Surface where the workpiece rests while performing a cutting, drilling, planing, or sanding operation. 9 Bevel Cut A cutting operation made with the blade at any ripping operation. Dado ...
English Manual
Page 12
LOOSE PARTS The following items are included with the drill press: Head Assembly 1 Column Assembly 1 Table 1 Table Support 1 Base 1 Hex Key (3 mm, 4 mm, and 5 mm 3 Hex Bolts (M8 4 Feed Handles 3 Worm Gear 1 Spindle Lock Lever 1 Table ...
LOOSE PARTS The following items are included with the drill press: Head Assembly 1 Column Assembly 1 Table 1 Table Support 1 Base 1 Hex Key (3 mm, 4 mm, and 5 mm 3 Hex Bolts (M8 4 Feed Handles 3 Worm Gear 1 Spindle Lock Lever 1 Table ...
English Manual
Page 22
...to remove dirt, dust, oil, grease, etc. ing the chuck in serious personal injury. After using solvents when cleaning plastic parts. GENERAL MAINTENANCE Avoid using the drill press, clean it . Apply a light coat of automotive-type paste wax to the table and column to help keep the vertical ...blow out any dust that could cause possible serious personal injury, turn off the tool, remove the switch key, and unplug the drill press before performing any other parts may result in one hand, tap the chuck tool lightly with a tapered shank are to help prolong the life of the...
...to remove dirt, dust, oil, grease, etc. ing the chuck in serious personal injury. After using solvents when cleaning plastic parts. GENERAL MAINTENANCE Avoid using the drill press, clean it . Apply a light coat of automotive-type paste wax to the table and column to help keep the vertical ...blow out any dust that could cause possible serious personal injury, turn off the tool, remove the switch key, and unplug the drill press before performing any other parts may result in one hand, tap the chuck tool lightly with a tapered shank are to help prolong the life of the...
English Manual
Page 24
... your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. DIGITAL DRILL PRESS DP121l • SERVICE Now that you call 1-800-525-2579 for a complete list of Authorized Service Centers. • MODEL NO. The model number of Ryobi Limited used under license. 983000-642 9-30-08 (REV...
... your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. DIGITAL DRILL PRESS DP121l • SERVICE Now that you call 1-800-525-2579 for a complete list of Authorized Service Centers. • MODEL NO. The model number of Ryobi Limited used under license. 983000-642 9-30-08 (REV...
Repair Sheet
Page 3
NO. May Be Purchased Locally DRILL PRESS - MODEL NUMBER DP121L The model number will be found on a plate attached to the motor housing. Always mention the model number in . PARTS LIST FOR FIGURE A KEY PART NO. NUMBER DESCRIPTION QTY. 1 089140300080 BEVEL STOP 1 36 089140200044 LIGHT SWITCH 2 2 089140300906 RPM LABEL 1 3 TDP07001... KEY (M4 X 60 mm 1 70 089140300047 POWER CORD 1 71 089140200082 HEX KEY (5 mm 1 * Standard Hardware Item - RYOBI 12 in all correspondence regarding your DRILL PRESS or when ordering repair parts. NUMBER DESCRIPTION KEY...
NO. May Be Purchased Locally DRILL PRESS - MODEL NUMBER DP121L The model number will be found on a plate attached to the motor housing. Always mention the model number in . PARTS LIST FOR FIGURE A KEY PART NO. NUMBER DESCRIPTION QTY. 1 089140300080 BEVEL STOP 1 36 089140200044 LIGHT SWITCH 2 2 089140300906 RPM LABEL 1 3 TDP07001... KEY (M4 X 60 mm 1 70 089140300047 POWER CORD 1 71 089140200082 HEX KEY (5 mm 1 * Standard Hardware Item - RYOBI 12 in all correspondence regarding your DRILL PRESS or when ordering repair parts. NUMBER DESCRIPTION KEY...
Repair Sheet
Page 4
... Purchased Locally RYOBI 12 in all correspondence regarding your DRILL PRESS or when ordering repair parts. MODEL NUMBER DP121L The model number will be found on a plate attached to the motor housing. PARTS LIST FOR FIGURE A KEY PART NO. DRILL PRESS - Always mention ... 134 089140200102 WASHER 3 135 089140200912 LASER LABEL 1 136 089140300081 * HEX NUT (M10 mm 1 137 089140300082 CAPACITOR (MOTOR) DP121L 1 138 089140300084 CABLE CLAMP 1 139 089140300085 INSULATING TAPE 1 140 089140300086 WASHER 1 141 089140300087 MOTOR CUSHION 1 983000642 OPERATOR'S MANUAL...
... Purchased Locally RYOBI 12 in all correspondence regarding your DRILL PRESS or when ordering repair parts. MODEL NUMBER DP121L The model number will be found on a plate attached to the motor housing. PARTS LIST FOR FIGURE A KEY PART NO. DRILL PRESS - Always mention ... 134 089140200102 WASHER 3 135 089140200912 LASER LABEL 1 136 089140300081 * HEX NUT (M10 mm 1 137 089140300082 CAPACITOR (MOTOR) DP121L 1 138 089140300084 CABLE CLAMP 1 139 089140300085 INSULATING TAPE 1 140 089140300086 WASHER 1 141 089140300087 MOTOR CUSHION 1 983000642 OPERATOR'S MANUAL...